In some cases, wireless door lock control functions are normal but the hazard warning light and wireless door lock buzzer answer-back function does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the body ECU may be malfunctioning.
When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
The wireless door lock buzzer answer-back function can be customized. Make sure that this function is ON before performing this.
Before performing the inspection, check that DTC B27B0 (Smart Entry and Start System) is not output.
If the body ECU has been replaced, it is necessary to initialize the body ECU.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Check the wireless door lock control function using the electrical key transmitter sub-assembly.
| Result | Proceed to |
|---|---|
| Wireless door lock/unlock operates properly | A |
| Wireless door lock/unlock does not operate properly | B |
A
B
for Front Side:
Remove the front door lock assembly.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock assembly.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
for Rear Side:
Remove the rear door lock assembly.
Inspect the rear door lock assembly.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Front Side) | B |
| NG (for Rear Side) | C |
A
B
C
for Driver Side:
Disconnect the J1 front door lock assembly RH connector.
Disconnect the G33 body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-7 (LSSR) - G33-15 (LSWD) | Always | Below 1 Ω |
| J1-8 (E) - Body ground | Always | Below 1 Ω |
| J1-7 (LSSR) or G33-15 (LSWD) - Body ground | Always | 10 kΩ or higher |
except Driver Side:
Disconnect the K1 front door lock assembly LH connector.
Disconnect the L1 rear door lock assembly RH connector.
Disconnect the M1 rear door lock assembly LH connector.
Disconnect the G33 body ECU connector.
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-8 (LSSR) - G33-2 (LSWP) | Always | Below 1 Ω |
| K1-8 (LSSR) - G16-9 (LSWP) | Always | Below 1 Ω |
| K1-7 (E) - Body ground | Always | Below 1 Ω |
| K1-8 (LSSR) or G33-2 (LSWP) - Body ground | Always | 10 kΩ or higher |
| K1-8 (LSSR) or G16-9 (LSWP) - Body ground | Always | 10 kΩ or higher |
| L1-6 (LSSR) - G33-2 (LSWP) | Always | Below 1 Ω |
| L1-6 (LSSR) - G16-9 (LSWP) | Always | Below 1 Ω |
| L1-9 (E) - Body ground | Always | Below 1 Ω |
| L1-6 (LSSR) - G33-2 (LSWP) - Body ground | Always | 10 kΩ or higher |
| L1-6 (LSSR) - G16-9 (LSWP) - Body ground | Always | 10 kΩ or higher |
| M1-6 (LSSR) - G33-2 (LSWP) | Always | Below 1 Ω |
| M1-6 (LSSR) - G16-9 (LSWP) | Always | Below 1 Ω |
| M1-9 (E) - Body ground | Always | Below 1 Ω |
| M1-6 (LSSR) - G33-2 (LSWP) - Body ground | Always | 10 kΩ or higher |
| M1-6 (LSSR) - G16-9 (LSWP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the wireless answer-back operation using the electrical key transmitter sub-assembly.
| Result | Proceed to |
|---|---|
| Only wireless door lock buzzer answer-back does not occur | A |
| Only hazard warning light answer-back does not occur | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer Operation | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer Operation |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not turn on/off | A |
| Wireless door lock buzzer turns on/off | B |
A
B
Disconnect the A41 wireless door lock buzzer connector.
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-1 - G16-2 (BZR) | Always | Below 1 Ω |
| A41-2 - Body ground | Always | Below 1 Ω |
| A41-1 or G16-2 (BZR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the wireless door lock buzzer with a new or known good one.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer Operation | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer Operation |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not turn on/off | A |
| Wireless door lock buzzer turns on/off | B |
A
B
Check that the hazard warning lights blink when the hazard warning signal switch is pressed.
Hazard warning lights blink.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G10 combination meter assembly connector.
Disconnect the G33 body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G10-2 (HAZ) - G33-6 (HAZ) | Always | Below 1 Ω |
| G10-2 (HAZ) or G33-6 (HAZ) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG