The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front air conditioning unit removal/installation are shown below.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.DRAIN ENGINE COOLANT
88710E
3.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
Remove the bolt and disconnect the air conditioner tube and accessory assembly.
Remove the 2 O-rings from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
4.DISCONNECT HEATER WATER OUTLET HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose.
Do not apply excessive force to the heater water outlet hose.
Prepare a drain pan or cloth in case the coolant leaks.
5.DISCONNECT HEATER WATER INLET HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose.
Do not apply excessive force to the heater water inlet hose.
Prepare a drain pan or cloth in case the coolant leaks.
87128
6.REMOVE HEATER GROMMET
Detach the claw and remove the heater grommet.
7.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL
8.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure described for the LH side.
55303B
9.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
87211A
10.REMOVE NO. 2 AIR DUCT
Remove the bolt.
Detach the claw and remove the No. 2 air duct.
When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.
If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.
87211
11.REMOVE NO. 1 AIR DUCT
Detach the claw and remove the No. 1 air duct.
When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.
If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.
12.REMOVE STEERING COLUMN ASSEMBLY
67914B
13.REMOVE FRONT DOOR SCUFF PLATE LH
62112
14.REMOVE COWL SIDE TRIM BOARD LH
67913B
15.REMOVE FRONT DOOR SCUFF PLATE RH
62111C
16.REMOVE COWL SIDE TRIM BOARD RH
67918E
17.REMOVE REAR DOOR SCUFF PLATE LH
67917C
18.REMOVE REAR DOOR SCUFF PLATE RH
62414A
19.REMOVE LOWER CENTER PILLAR GARNISH LH
62413A
20.REMOVE LOWER CENTER PILLAR GARNISH RH
21.REMOVE FRONT FLOOR CARPET ASSEMBLY
Remove the 5 clips.
|
Fastener |
|
Remove in this Direction |
Detach each fastener.
Detach the guide and fold back the front floor carpet assembly as shown in the illustration.
55215D
22.REMOVE NO. 3 DASH PANEL INSULATOR PAD
|
Remove in this Direction |
Remove the No. 3 dash panel insulator pad as shown in the illustration.
55214C
23.REMOVE NO. 2 DASH PANEL INSULATOR PAD
|
Remove in this Direction |
Remove the No. 2 dash panel insulator pad as shown in the illustration.
87216B
24.REMOVE NO. 4 REAR AIR DUCT
Detach the claw and remove the No. 4 rear air duct.
87216A
25.REMOVE NO. 5 REAR AIR DUCT
Detach the claw and remove the No. 5 rear air duct.
87213
26.REMOVE NO. 2 REAR AIR DUCT
Detach the claw and remove the No. 2 rear air duct.
87212G
27.REMOVE NO. 3 REAR AIR DUCT
Detach the claw and remove the No. 3 rear air duct.
87212
28.REMOVE NO. 1 REAR AIR DUCT
Remove the 2 clips and remove the No. 1 rear air duct.
55306A
29.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Nut |
|
Bolt |
|
Screw |
Detach the clamp.
Remove the nut, bolt, 4 screws and No. 1 instrument panel brace sub-assembly.
55307C
30.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Nut |
|
Bolt |
|
Screw |
Remove the nut, bolt, 3 screws and No. 2 instrument panel brace sub-assembly.
82141
31.DISCONNECT INSTRUMENT PANEL WIRE
for Automatic Air Conditioning System:
Disconnect the connector.
Detach the clamp.
for Manual Air Conditioning System:
Disconnect the connector.
Detach the clamp.
Remove each bolt and each ground wire.
| *A | for Manual Air Conditioning System | *B | for Automatic Air Conditioning System |
| *C | w/ PTC Heater | - | - |
| *1 | Ground Wire | - | - |
Disconnect each connector and detach each clamp.
Remove each bolt, nut and screw, and then disconnect the instrument panel wire.
55330B
32.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When removing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
| *A | for Driver Side |
|
Protective Tape |
Put protective tape around the hole plug.
Using a screwdriver with its tip wrapped with protective tape, remove the 2 hole plugs.
for Automatic Transmission:
Remove the 11 bolts.
| *A | for Manual Transmission | - | - |
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
for Manual Transmission:
Remove the 12 bolts.
55950G
33.REMOVE DEFROSTER NOZZLE ASSEMBLY
Detach the claw and remove the defroster nozzle assembly.
34.REMOVE AIR CONDITIONING UNIT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Disconnect the drain cooler hose.
Remove the nut and air conditioning unit assembly and instrument panel reinforcement assembly.
87211B
35.REMOVE NO. 3 AIR DUCT
Detach the claw and remove the No. 3 air duct.