Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041708 METER / GAUGE / DISPLAY _0203147 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the brake actuator assembly (skid control ECU) which uses this information to create the vehicle speed signal*. The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the brake actuator assembly (skid control ECU). The pulse signal is created by switching the transistor in the brake actuator assembly (skid control ECU) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the brake actuator assembly (skid control ECU). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*: This vehicle speed signal is created by the brake actuator assembly (skid control ECU). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E326471E01
0.354,1.188 0.667,1.385 0.313,0.198 10 false A4 0.354,1.354 3.146,1.583 2.792,0.229 10 false Brake Actuator Assembly (Skid Control ECU) 1.5,0.469 1.813,0.667 0.313,0.198 10 false SP1 5.115,0.458 5.427,0.656 0.313,0.198 10 false 18 1.844,0.458 2.156,0.656 0.313,0.198 10 false 14 5.354,0.479 5.667,0.677 0.313,0.198 10 false SI 5.031,2.917 5.344,3.115 0.313,0.198 10 false G8 5.031,3.073 6.844,3.313 1.813,0.24 10 false Combination Meter Assembly 5.125,2.479 5.438,2.677 0.313,0.198 10 false 19 5.365,2.49 5.677,2.688 0.313,0.198 10 false +S 6.375,2.26 6.688,2.458 0.313,0.198 10 false CPU 1.469,2.5 1.781,2.698 0.313,0.198 10 false SPD 0.729,2.979 1.042,3.177 0.313,0.198 10 false G49 0.708,3.125 3.5,3.354 2.792,0.229 10 false ECM 1.854,2.479 2.167,2.677 0.313,0.198 10 false 10 0.302,4.313 0.615,4.51 0.313,0.198 10 false G16 0.313,4.458 3.146,4.76 2.833,0.302 10 false Certification ECU (Smart Key ECU Assembly) 1.479,3.927 1.792,4.125 0.313,0.198 10 false SPD 1.865,3.885 2.177,4.083 0.313,0.198 10 false 7 5.375,3.906 5.688,4.104 0.313,0.198 10 false SPD 5.177,3.906 5.49,4.104 0.313,0.198 10 false 5 5.313,4.427 5.625,4.625 0.313,0.198 10 false G33 5.333,4.594 6.146,4.885 0.813,0.292 10 false Body ECU 4.385,5.854 4.792,6.031 0.406,0.177 10 false G100 4.396,6.021 6.854,6.365 2.458,0.344 10 false Radio and Display Receiver Assembly*2 5.365,5.479 5.677,5.677 0.313,0.198 10 false SPD 5.115,5.479 5.427,5.677 0.313,0.198 10 false 17 1.469,5.479 1.781,5.677 0.313,0.198 10 false SPD 1.854,5.469 2.167,5.667 0.313,0.198 10 false 17 0.344,5.865 0.75,6.042 0.406,0.177 10 false G41 0.354,6.031 2.813,6.375 2.458,0.344 10 false Navigation Receiver Assembly*1 0.156,6.302 2.615,6.646 2.458,0.344 10 false *1: w/ Navigation System 0.146,6.531 2.615,6.792 2.469,0.26 10 false *2: w/ Audio and Visual System

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

·

w/ Smart Entry and Start System:

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

w/ Navigation System:

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

w/ Audio and Visual System (for Radio and Display Type):

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION



PROCEDURE

1.CHECK ECM

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)


a.
C240157C38
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.271 1.938,0.427 0.313,0.156 10 false G8 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G41 navigation receiver assembly connector.*1


c.

Disconnect the G100 radio and display receiver assembly connector.*2


d.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the G33 body ECU connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)


a.
C240157C38
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.271 1.938,0.427 0.313,0.156 10 false G8 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G41 navigation receiver assembly connector.*1


c.

Disconnect the G100 radio and display receiver assembly connector.*2


d.

Disconnect the G33 body ECU connector.


e.

Disconnect the G49 ECM connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK BODY ECU

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
3.CHECK BODY ECU

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)


a.
C240157C38
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.271 1.938,0.427 0.313,0.156 10 false G8 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G41 navigation receiver assembly connector.*1


c.

Disconnect the G100 radio and display receiver assembly connector.*2


d.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the G49 ECM connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Result Proceed to
OK (w/ Navigation System) A
OK (w/ Audio and Visual System [for Radio and Display Type]) B
NG C



A

4.CHECK NAVIGATION RECEIVER ASSEMBLY

B

9.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

C

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)
4.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
C240157C38
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.271 1.938,0.427 0.313,0.156 10 false G8 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the G49 ECM connector.


d.

Disconnect the G33 body ECU connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
5.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-14 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
6.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E200403C10
1.521,0.26 1.917,0.479 0.396,0.219 1.052,1.125 0.771,0.865 0.771,0.865 0.615,0.865 true 0.406,0.76 0.708,1.073 0.302,0.313 10 false SI 1.625,0.281 1.99,0.469 0.365,0.188 10 false G8 1.333,4.094 1.458,4.24 0.125,0.146 10 false A 2.969,3.51 3.427,3.885 0.458,0.375 10 false GND 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.094,2.448 0.406,2.604 0.313,0.156 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.


b.

Connect an oscilloscope to terminal G8-18 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G8-18 (SI) - Body ground
Tool Setting 5 V/DIV, 20 ms./DIV
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)


a.

Disconnect the G8 combination meter assembly connector.


b.

Disconnect the G41 navigation receiver assembly connector.*1


c.

Disconnect the G100 radio and display receiver assembly connector.*2


d.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the G33 body ECU connector.


f.

Disconnect the G49 ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-19 (+S) - G49-10 (SPD) Always Below 1 Ω
G8-19 (+S) or G49-10 (SPD) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)


a.

Disconnect the G8 combination meter assembly connector.


b.

Disconnect the G41 navigation receiver assembly connector.*1


c.

Disconnect the G100 radio and display receiver assembly connector.*2


d.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the G33 body ECU connector.


f.

Disconnect the G49 ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-19 (+S) - G16-7 (SPD) Always Below 1 Ω
G8-19 (+S) or G16-7 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
C240157C38
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.271 1.938,0.427 0.313,0.156 10 false G8 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the G49 ECM connector.


d.

Disconnect the G33 body ECU connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the G8 combination meter assembly connector.


b.

Disconnect the G41 navigation receiver assembly connector.


c.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G33 body ECU connector.


e.

Disconnect the G49 ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-19 (+S) - G41-17 (SPD) Always Below 1 Ω
G8-19 (+S) or G41-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the N34 combination meter assembly connector.


b.

Disconnect the A4 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-18 (SI) - A4-14 (SP1) Always Below 1 Ω
G8-18 (SI) or A4-14 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G8 combination meter assembly connector.


b.

Disconnect the G100 radio and display receiver assembly connector.


c.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G33 body ECU connector.


e.

Disconnect the G49 ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-19 (+S) - G100-17 (SPD) Always Below 1 Ω
G8-19 (+S) or G100-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)


a.

Disconnect the G8 combination meter assembly connector.


b.

Disconnect the G41 navigation receiver assembly connector.*1


c.

Disconnect the G100 radio and display receiver assembly connector.*2


d.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the G33 body ECU connector.


f.

Disconnect the G49 ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-19 (+S) - G33-5 (SPD) Always Below 1 Ω
G8-19 (+S) or G33-5 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR