Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM3270E _59 Vehicle Exterior _041716 WINDOW / GLASS _0206024 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 62704A 1.INSTALL REAR QUARTER WINDOW GLASS RETAINER SUB-ASSEMBLY LH

a.
B409253

Attach the clip.


b.

Install the rear quarter window glass retainer sub-assembly LH with the screw.


Hide 62720A 2.CLEAN QUARTER WINDOW ASSEMBLY LH

a.

Clean the outer edges of a new quarter window assembly LH with non-residue solvent.


Hide 62763J 3.INSTALL UPPER QUARTER WINDOW GLASS RETAINER

a.

Apply Primer G to the upper quarter window glass retainer installation area on the quarter window glass LH.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new upper quarter window glass retainer.


c.
B409240C01
2.146,1.031 2.302,1.229 false 2.01,0.542 1.708,0.521 1.708,0.521 1.594,0.969 false 2.323,1.281 2.635,1.438 0.313,0.156 10 false *1 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 1.573,0.344 1.885,0.5 0.313,0.156 10 false *b
*1 Upper Quarter Window Glass Retainer
*a Back Side of Quarter Window Glass LH
*b Ceramic Notch


Install the upper quarter window glass retainer to the quarter window glass LH in the location shown in the illustration.

NOTICE:

Install the upper quarter window glass retainer after Primer G has been allowed to dry (approximately 3 minuts).



Hide 62761H 4.INSTALL FRONT QUARTER WINDOW GLASS RETAINER

a.

Apply Primer G to the front quarter window glass retainer installation area on the quarter window glass LH.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new front quarter window glass retainer.


c.
B409241C01
2.146,2.667 2.24,2.885 false 2.094,2.083 1.615,2.146 1.615,2.146 1.542,2.667 false 2.188,2.927 2.5,3.083 0.313,0.156 10 false *1 0.063,0.073 0.375,0.229 0.313,0.156 10 false *a 1.438,1.979 1.75,2.135 0.313,0.156 10 false *b
*1 Front Quarter Window Glass Retainer
*a Back Side of Quarter Window Glass LH
*b Ceramic Notch


Install the front quarter window glass retainer to the quarter window glass LH in the location shown in the illustration.

NOTICE:

Install the front quarter window glass retainer after Primer G has been allowed to dry (approximately 3 minuts).



Hide 69998B 5.INSTALL NO. 2 QUARTER WINDOW GUIDE PIECE PIN

a.

Apply Primer G to the No. 2 quarter window guide piece pin installation area on the quarter window glass LH.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new No. 2 quarter window guide piece pin.


c.
B409242C01
1.729,2.333 1.458,2.25 false 2.333,2.521 2.198,2.906 2.198,2.906 1.771,2.906 false 1.26,2.177 1.573,2.333 0.313,0.156 10 false *1 0.063,0.031 0.375,0.188 0.313,0.156 10 false *a 2.188,2.906 2.5,3.063 0.313,0.156 10 false *b
*1 No. 2 Quarter Window Guide Piece Pin
*a Back Side of Quarter Window Glass LH
*b Ceramic Notch


Install the No. 2 quarter window guide piece pin to the quarter window glass LH in the location shown in the illustration.

NOTICE:

Install the No. 2 quarter window guide piece pin after Primer G has been allowed to dry (approximately 3 minuts).



Hide 62767B 6.INSTALL REAR QUARTER WINDOW GLASS RETAINER

a.

Apply Primer G to the rear quarter window glass retainer installation area on the quarter window glass LH.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new rear quarter window glass retainer.


c.
B409243C01
1.469,0.823 1.281,0.667 false 2.021,0.75 2.01,1.188 2.01,1.188 1.635,1.375 false 1.083,0.542 1.396,0.698 0.313,0.156 10 false *1 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 2.063,1.167 2.375,1.323 0.313,0.156 10 false *b
*1 Rear Quarter Window Glass Retainer
*a Back Side of Quarter Window Glass LH
*b Ceramic Notch


Install the rear quarter window glass retainer to the quarter window glass LH in the location shown in the illustration.

NOTICE:

Install the rear quarter window glass retainer after Primer G has been allowed to dry (approximately 3 minuts).



Hide 62765H 7.INSTALL LOWER QUARTER WINDOW GLASS RETAINER

a.

Apply Primer G to the lower quarter window glass retainer installation area on the quarter window glass LH.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new lower quarter window glass retainer.


c.
B409244C01
1.344,2.167 1.094,2.031 false 1.969,2.125 1.927,2.49 1.927,2.49 1.583,2.573 false 0.885,1.927 1.198,2.083 0.313,0.156 10 false *1 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.938,2.5 2.25,2.656 0.313,0.156 10 false *b
*1 Lower Quarter Window Glass Retainer
*a Back Side of Quarter Window Glass LH
*b Ceramic Notch


Install the lower quarter window glass retainer to the quarter window glass LH in the location shown in the illustration.

NOTICE:

Install the lower quarter window glass retainer after Primer G has been allowed to dry (approximately 3 minuts).



Hide 56117C 8.INSTALL REAR SIDE WINDOW GLASS ADHESIVE DAM

a.

Apply Primer G to the rear side window glass adhesive dam installation area of the quarter window glass.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new rear side window glass adhesive dam.


c.

Install the rear side window glass adhesive dam to the quarter window glass in the location shown in the illustration.

B409245C01
6.01,2.552 5.719,2.917 false 1.417,1.417 1.656,0.99 true 1.219,1.688 1.583,1.75 false 5.073,1.229 4.823,0.938 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.573,1.875 3.729,2.073 0.156,0.198 10 false A 3.594,2.396 3.75,2.594 0.156,0.198 10 true A 5.531,1.656 6.302,1.854 0.771,0.198 10 false A - A 1.698,0.917 2.01,1.115 0.313,0.198 10 false *b 5.625,2.958 5.938,3.156 0.313,0.198 10 false *b 1.615,1.688 1.927,1.885 0.313,0.198 10 false *c 4.656,0.792 4.969,0.99 0.313,0.198 10 false *b 5.833,1.906 5.99,2.104 0.156,0.198 10 false a
*a Back Side of Quarter Window Glass LH *b Rear Side Window Glass Adhesive Dam Center Line
*c Ceramic Notch - -


NOTICE:

Install the rear side window glass adhesive dam after Primer G has been allowed to dry (approximately 3 minuts).


Standard:
Area Measurement
a 3.1 mm (0.122 in.)



Hide 9.INSTALL QUARTER WINDOW MOULDING LH

a.
B415226C01
0.792,1.417 0.49,1.24 false 2.896,0.854 3.083,1.073 false 2.385,1.344 2.542,1.542 0.156,0.198 10 false a 0.833,1.396 1.146,1.594 0.313,0.198 10 false *1 3.115,1.073 3.427,1.271 0.313,0.198 10 false *2
*1 Quarter Window Moulding LH
*2 Quarter Window Glass LH
V100155

Primer G


Apply Primer G to the quarter window moulding LH installation area of the quarter window glass LH and new quarter window moulding LH.

NOTICE:

Do not apply too much Primer G.


Standard:
Area Specified Condition
a 11.8 mm (0.465 in.)



b.
B409246C01
0,0 0,0 false
V100155

Adhesive


Apply adhesive to the quarter window moulding LH.

i.

Cut off the tip of a cartridge nozzle.


ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the quarter window moulding LH as shown in the illustration.

NOTICE:

Apply the adhesive after Primer G has been allowed to dry (approximately 3 minuts).




c.

Remove the peeling paper and install the quarter window moulding LH.


d.

Install the quarter window moulding LH as shown in the illustration.

B409247C01
5.844,0.573 5.938,0.344 true 4.542,2.177 4.427,2.396 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 6.031,0.26 6.344,0.458 0.313,0.198 10 false *b 4.281,2.417 4.594,2.615 0.313,0.198 10 false *b
*a Back Side of Quarter Window Glass LH *b R End



e.

Apply non-residue solvent to a clean cloth and wipe off any excess or protruding adhesive.


Hide 62785A 10.INSTALL QUARTER WINDOW GLASS SPACER

a.

Apply Primer G to the quarter window glass spacer installation area on the quarter window glass LH.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new quarter window glass spacer.


c.
B409248C01
1.271,2.99 1.354,2.677 false 0.771,2.542 0.854,2.24 false 1.854,2.531 1.698,2.167 false 1.198,3.01 1.51,3.167 0.313,0.156 10 false *1 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.875,2.083 1.188,2.24 0.313,0.156 10 false *b 1.521,2.073 1.833,2.271 0.313,0.198 10 false *b
*1 Quarter Window Glass Spacer
*a Back Side of Quarter Window Glass LH
*b Ceramic Notch


Install the quarter window glass spacer to the quarter window glass LH in the location shown in the illustration.

NOTICE:

Install the quarter window glass spacer after Primer G has been allowed to dry (approximately 3 minuts).



Hide 62775C 11.INSTALL QUARTER WINDOW CLIP

a.

Apply Primer G to the quarter window clip installation area of the quarter window glass LH.

NOTICE:

Do not apply too much Primer G.


B414249C01
1.688,2.198 1.896,2.458 false 2.854,2.156 2.604,2 false 3.719,2.125 3.979,2.469 false 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 1.938,2.417 2.25,2.615 0.313,0.198 10 false *b 2.438,1.896 2.75,2.094 0.313,0.198 10 false *b 4.01,2.448 4.323,2.646 0.313,0.198 10 false *b 4.76,0.906 4.917,1.104 0.156,0.198 10 true A 4.74,1.448 4.896,1.646 0.156,0.198 10 true A 5.885,1.448 6.656,1.646 0.771,0.198 10 false A - A
*a Back Side of Quarter Window Glass LH *b Ceramic Line
V100155

Primer G - -



b.

Apply adhesive to the location shown in the illustration and install the 8 quarter window clips (for Type A) and quarter window clip (for Type B) to the quarter window glass LH in the location shown in the illustration.

B409249C01
1.531,2.385 1.177,2.51 false 3.448,2.385 3.115,2.542 false 5.271,2.375 5.021,2.5 false 2.146,2.073 2.281,1.969 false 4.021,2.083 4.26,1.927 false 3.063,2.083 2.844,2.073 false 4.969,2.083 4.802,2.063 false 5.958,2.083 6.094,2.01 false 0.854,1.781 1.167,1.938 0.313,0.156 10 false *A 4.667,1.781 4.979,1.938 0.313,0.156 10 false *B 0.969,2.438 1.281,2.594 0.313,0.156 10 false *1 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 2.635,1.792 2.948,1.99 0.313,0.198 10 false *A 2.906,2.458 3.219,2.656 0.313,0.198 10 false *1 4.833,2.438 5.146,2.635 0.313,0.198 10 false *1 1.927,2.792 2.698,2.99 0.771,0.198 10 false A - A 2.167,0.99 2.323,1.188 0.156,0.198 10 true A 2.146,1.469 2.302,1.667 0.156,0.198 10 true A 2.323,1.875 2.635,2.073 0.313,0.198 10 false *b 4.313,1.844 4.625,2.042 0.313,0.198 10 false *b 2.656,1.969 2.969,2.167 0.313,0.198 10 false *b 4.646,1.979 4.958,2.177 0.313,0.198 10 false *b 6.115,1.906 6.427,2.104 0.313,0.198 10 false *b
*A for Type A *B for Type B
*1 Quarter Window Clip - -
*a Back Side of Quarter Window Glass LH *b Ceramic Line
V100155

Adhesive - -



c.

Using a scraper, remove any excess adhesive or apply as necessary.

NOTICE:

Apply adhesive up to the edge of the windshield glass.



Hide 75646 12.INSTALL REAR OUTSIDE QUARTER WINDOW MOULDING LH

a.

After the adhesive hardens, attach the claw to install the rear outside quarter window moulding LH as shown in the illustration.

B409250C01
2.917,2.708 3.333,2.542 false 3.219,3.125 2.896,2.969 false 2.719,2.615 3.031,2.813 0.313,0.198 10 false *1 2.708,2.875 3.021,3.073 0.313,0.198 10 false *2
*1 Quarter Window Clip (for Type B) *2 Rear Outside Quarter Window Moulding LH
V113147

Install in this Direction
V113148

Install in this Order



Hide 62720A 13.INSTALL QUARTER WINDOW ASSEMBLY LH

a.
B388038C01
0.906,0.656 0.563,0.458 false 2.729,0.646 2.406,0.479 false 2.229,0.385 2.542,0.542 0.313,0.156 10 false *1 0.354,0.396 0.667,0.552 0.313,0.156 10 false *1
*1 Vehicle Body
V100155

Adhesive


Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.




b.

Clean the outer edges of the quarter window assembly LH with non-residue solvent.


c.

Quarter window assembly LH preliminary installation procedures.

i.

Install the suction cups to a new quarter window assembly LH.


ii.

Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Do not apply too much Primer M.

·

Do not apply Primer M to the adhesive.

·

Be careful when applying primer to the panel joints and spot welds.

·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.





d.

Apply Primer G to the quarter window glass assembly LH in the locations shown in the illustration.

B409251C01
1.156,2.042 3.354,2.833 2.198,0.792 1.156,2.927 3.354,3.698 2.198,0.771 3.521,2.031 5.875,2.844 2.354,0.813 3.521,2.938 5.875,3.708 2.354,0.771 2.188,2.5 2.542,2.656 true 4.552,2.51 4.948,2.708 4.948,2.708 4.771,2.51 true 2.188,3.396 1.76,3.563 true 4.302,3.385 4.792,3.594 true 2.063,2.063 2.219,2.26 0.156,0.198 10 false a 2.052,2.938 2.208,3.135 0.156,0.198 10 false a 4.438,2.073 4.594,2.271 0.156,0.198 10 false a 4.229,2.979 4.385,3.177 0.156,0.198 10 false b 4.333,0.063 4.49,0.26 0.156,0.198 10 false A 4.344,0.708 4.5,0.906 0.156,0.198 10 true A 5.229,0.26 5.385,0.458 0.156,0.198 10 true B 5.708,0.844 5.865,1.042 0.156,0.198 10 false B 3.51,1.104 3.667,1.302 0.156,0.198 10 false C 3.542,1.771 3.698,1.969 0.156,0.198 10 false C 1.813,0.51 1.969,0.708 0.156,0.198 10 false D 2.448,0.927 2.604,1.125 0.156,0.198 10 true D 1.25,2.083 2.021,2.281 0.771,0.198 10 false A - A 3.583,2.063 4.354,2.26 0.771,0.198 10 false B - B 1.229,2.969 2,3.167 0.771,0.198 10 false C - C 3.594,2.969 4.365,3.167 0.771,0.198 10 false D - D 2.615,2.625 2.927,2.823 0.313,0.198 10 false *b 5.021,2.677 5.333,2.875 0.313,0.198 10 false *b 1.552,3.469 1.865,3.667 0.313,0.198 10 false *b 4.875,3.542 5.146,3.729 0.271,0.188 10 false *b 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a
*a Back Side of Quarter Window Assembly LH *b Adhesive Application Center Line
V100155

Primer G Application Area - -


Standard:
Area Measurement
a 7.0 mm (0.276 in.)
b 20.0 mm (0.787 in.)


HINT:

If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




e.

Apply adhesive to the quarter window assembly LH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800C94
1.198,0.448 1.406,0.521 true 2.521,0.563 2.917,0.385 true 1.292,1.448 1.385,1.604 0.094,0.156 10 false a 2.948,0.292 3.135,0.49 0.188,0.198 10 false *1 0.583,0.615 0.677,0.771 0.094,0.156 10 false a 1.115,0.875 1.208,1.031 0.094,0.156 10 false b 0.781,1.01 0.875,1.167 0.094,0.156 10 false b 1.458,0.479 1.646,0.677 0.188,0.198 10 false *2
*1 Sealer Gun
*2 Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours




f.

Load the sealer gun with the cartridge.


g.

Apply a bead of adhesive to the quarter window assembly LH in the locations shown in the illustration.

B409252C01
1.469,2.042 3.313,2.792 1.844,0.75 3.542,2.052 5.823,2.802 2.281,0.75 1.469,2.927 3.302,3.677 1.833,0.75 3.552,2.927 5.833,3.667 2.281,0.74 2.188,2.51 2.698,2.667 true 2.208,3.365 2.615,3.177 true 4.563,2.5 4.333,2.698 4.333,2.698 4.771,2.51 false 4.333,3.365 4.708,3.188 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 4.302,0.052 4.458,0.25 0.156,0.198 10 false A 4.323,0.688 4.479,0.885 0.156,0.198 10 true A 5.188,0.25 5.344,0.448 0.156,0.198 10 true B 5.698,0.865 5.854,1.063 0.156,0.198 10 false B 3.51,1.115 3.667,1.313 0.156,0.198 10 false C 3.51,1.781 3.667,1.979 0.156,0.198 10 false C 1.729,0.573 1.885,0.771 0.156,0.198 10 false D 2.427,0.969 2.583,1.167 0.156,0.198 10 true D 0.521,2.781 0.677,2.979 0.156,0.198 10 false a 1.063,3.302 1.219,3.5 0.156,0.198 10 false b 1.521,2.094 2.292,2.292 0.771,0.198 10 false A - A 3.594,2.094 4.365,2.292 0.771,0.198 10 false B - B 1.531,2.99 2.302,3.188 0.771,0.198 10 false C - C 3.615,2.979 4.385,3.177 0.771,0.198 10 false D - D 4.76,3.104 5.052,3.313 0.292,0.208 10 false *b 4.125,2.625 4.438,2.823 0.313,0.198 10 false *b 2.729,2.615 3.042,2.813 0.313,0.198 10 false *b 2.635,3.073 2.948,3.271 0.313,0.198 10 false *b
*a Back Side of Quarter Window Glass Assembly LH *b Adhesive Application Center Line
V100155

Adhesive - -


Area:
Area Measurement
a 8.0 mm (0.315 in.)
b 12.0 mm (0.472 in.)


NOTICE:

Apply the adhesive after Primer G has been allowed to dry (approximately 3 minuts).



h.

Using suction cups, attach the 4 clips to install the quarter window assembly LH.

NOTICE:
·

Install the quarter window assembly LH after Primer M on the vehicle body has been allowed to dry (approximately 3 minuts).

·

From the interior, check that the quarter window assembly LH is securely attached.




i.

Lightly press the quarter window assembly LH from outside the vehicle so that it is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.



j.

Using a scraper, remove any excess adhesive or apply as necessary.


k.

Remove any excess adhesive before it hardens.


l.

Hold the quarter window assembly LH in place securely with protective tape or equivalent until the adhesive hardens.

HINT:

Follow the instructions for each adhesive manufacturer or the corresponding owner's manual for the minimum amount of time necessary prior to driving the vehicle.



Hide 14.CHECK FOR QUARTER WINDOW ASSEMBLY LH

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


c.

Remove any protective tape.


Hide 62792V 15.INSTALL UPPER QUARTER WINDOW MOULDING LH

Hide 62472D 16.INSTALL UPPER REAR PILLAR GARNISH LH

Hide 73178B 17.INSTALL SEAT BELT ANCHOR COVER CAP

Hide 62639A 18.INSTALL QUARTER PILLAR GARNISH LH

Hide 73178B 19.INSTALL SEAT BELT ANCHOR COVER CAP

Hide 62512 20.INSTALL QUARTER INSIDE TRIM BOARD LH

Hide 73233B 21.INSTALL REAR NO. 2 SEAT OUTER LAP BELT ANCHOR COVER

Hide 73233A 22.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

Hide 67935 23.INSTALL BACK DOOR SCUFF PLATE

Hide 67918E 24.INSTALL REAR DOOR SCUFF PLATE LH

Hide 25.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 26.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION