Home › Engine / Hybrid System › 1KD-FTV LUBRICATION › OIL PUMP › from 2016.01
RM3270E _51 Engine / Hybrid System _048920 1KD-FTV LUBRICATION _0242496 OIL PUMP A

1KD-FTV LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the oil pump removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of ECM
·

Learning values save

·

Learning values write

·

Vehicle Identification Number (VIN) registration


·

Engine starting

·

DTC P0630 is output


(Click here)
Code registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.
Replacement of engine assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)
Replacement of fuel supply pump assembly Supply Pump Initialization Engine startability (Click here)
·

Replacement of diesel throttle body assembly

·

Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor


Perform initialization - (Click here)
Replacement of timing belt Mode reset operation
·

Does not illuminate when replacement is necessary

·

Illuminates when replacement is not necessary


(Click here)
for A750F:
·

Automatic transmission assembly

·

Transmission valve body assembly

·

Any of the shift solenoid valves


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for A750F:

Automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
w/ Automatic Headlight Beam Level Control System:

The vehicle height changes due to replacement of suspension components or after performing such operations as removal and reinstallation


Headlight leveling ECU assembly initialization Headlight leveling function (Click here)
for 4WD:

Front wheel alignment adjustment


·

Clearing zero point calibration data

·

Yaw rate and acceleration sensor zero point calibration


VSC malfunctioning (Click here)

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 11322A 6.REMOVE NO. 1 TIMING BELT COVER

Hide 13505 8.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 9.REMOVE NO. 2 IDLE PULLEY ASSEMBLY

Hide 27020 10.REMOVE GENERATOR ASSEMBLY

Hide 12511C 11.REMOVE GENERATOR BRACKET

Hide 16620 12.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 88431 13.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 23701 15.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 23704 16.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 15301 17.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23804C 18.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 11201 19.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 13523P 20.REMOVE CAMSHAFT TIMING PULLEY

Hide 11322B 21.REMOVE NO. 2 TIMING BELT COVER

Hide 16100 22.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 29300 23.REMOVE VACUUM PUMP ASSEMBLY

Hide 44320 24.REMOVE VANE PUMP ASSEMBLY

Hide 13522P 27.REMOVE PUMP DRIVE SHAFT PULLEY

a.
A352007

Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley from the timing gear cover.


b.
A352008N01
1.781,1.188 2.448,1.656 2.448,1.656 2.656,1.656 true 0.635,1.625 0.792,1.625 0.792,1.625 1.104,1.365 true 0.302,1.531 0.625,1.729 0.323,0.198 10 true SST 2.688,1.573 3.01,1.771 0.323,0.198 10 true SST

Using SST, hold the crankshaft pulley and remove the nut and O-ring.

SST
09213-58014  (91551-80840)
09330-00021  


Hide 13408 28.REMOVE CRANKSHAFT PULLEY SUB-ASSEMBLY

Hide 19315 31.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 13521 32.REMOVE CRANKSHAFT TIMING GEAR

Hide 13572 33.REMOVE IDLE GEAR THRUST PLATE

Hide 13581 35.REMOVE NO. 1 IDLE GEAR SHAFT

Hide 22100 36.REMOVE FUEL SUPPLY PUMP ASSEMBLY

Hide 12101 37.REMOVE OIL PAN SUB-ASSEMBLY

Hide 15104 38.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 11320 39.REMOVE TIMING GEAR CASE ASSEMBLY