The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
No. 3 injection pipe sub-assembly ·
No. 4 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing Gear Case Assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
51410
3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
51442
4.REMOVE NO. 2 ENGINE UNDER COVER
5.DRAIN ENGINE OIL
6.DRAIN ENGINE COOLANT
7.DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)
8.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
9.DRAIN POWER STEERING FLUID
53301
10.REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose from the hood sub-assembly.
Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.
16400
11.REMOVE RADIATOR ASSEMBLY
17940D
12.REMOVE INTERCOOLER ASSEMBLY
55550
13.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
82121
14.DISCONNECT ENGINE WIRE
Remove the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| *A | for LHD |
| *B | for RHD |
Disconnect the 3 connectors from the injector driver.
| *A | for LHD |
| *B | for RHD |
Detach the grommet and pull out the engine wire from the cabin.
15.REMOVE AIR CLEANER CAP AND HOSE
17801
16.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
18.DISCONNECT WATER HOSE SUB-ASSEMBLY
Slide the 2 clamps and disconnect the water hose sub-assembly from the water outlet and heater pipe.
19.DISCONNECT FUEL HOSE
Slide the 2 clamps and disconnect the No. 1 fuel hose and No. 2 fuel hose from the No. 2 nozzle leakage pipe assembly and fuel supply pump assembly.
44774
20.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Slide the clamp and disconnect the union to connector tube hose from the No. 1 hose to hose tube.
21.DISCONNECT WIRE HARNESS
Detach the 3 clips and remove the No. 1 relay block cover upper from the engine room relay block sub-assembly.
Detach the 2 clips and remove the No. 1 relay block cover side from the engine room relay block sub-assembly.
Remove the nut and disconnect the wire to wire from the engine room relay block sub-assembly.
Disconnect the 2 connectors from the engine room relay block sub-assembly.
Detach the clamp and remove the 2 bolts and disconnect the No. 2 engine wire.
Remove the nut and disconnect the engine room main wire from the battery positive cable.
74404B
22.REMOVE BATTERY CLAMP SUB-ASSEMBLY
Loosen the 2 nuts and remove the battery clamp sub-assembly from the body.
28800
23.REMOVE BATTERY
74431
24.REMOVE BATTERY TRAY
44410
25.DISCONNECT PRESSURE FEED TUBE ASSEMBLY
Slide the clamp and disconnect the oil reservoir to pump hose from the vane pump assembly.
Disconnect the pressure feed tube assembly from the vane pump assembly.
88320
26.DISCONNECT COOLER COMPRESSOR ASSEMBLY
Remove the 4 bolts and disconnect the cooler compressor assembly from the No. 1 compressor mounting bracket.
It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.
17410
27.REMOVE FRONT EXHAUST PIPE ASSEMBLY
37140
28.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TSAM Made)>REMOVAL
except TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(except TSAM Made)>REMOVAL
37100
29.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TSAM Made)>REMOVAL
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>REMOVAL
33030
30.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
32101A
31.REMOVE DRIVE PLATE AND TORQUECONVERTER SETTING BOLT (for Automatic Transmission)
35000
32.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
31210
33.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
31250
34.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
13405
35.REMOVE FLYWHEEL SUB-ASSEMBLY
Using SST, hold the crankshaft pulley sub-assembly.
for Manual Transmission:
Remove the 8 bolts and flywheel sub-assembly from the crankshaft.
for Automatic Transmission:
Remove the 8 bolts, the rear drive plate spacer, the pump impeller drive plate and the flywheel sub-assembly from the crankshaft.
11355
36.REMOVE REAR END PLATE
Remove the bolt and rear end plate from the cylinder block sub-assembly.
37.INSTALL ENGINE HANGER
| *1 | No. 1 Engine Hanger Upper |
| *2 | No. 2 Engine Hanger |
Install the No. 1 engine hanger upper and No. 2 engine hanger with 2 bolts as shown in the illustration.
Part No.
| No. 1 engine hanger upper | 12284-30020 |
| No. 2 engine hanger | 12282-67030 |
| Bolt | 90105-T0164 and 90119-T0065 |
Install the engine hangers with new bolts.
38.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine assembly with a chain block.
Remove the 4 bolts and 4 nuts from the body.
Remove the engine assembly by operating the engine sling device and chain block.
Make sure that the engine assembly is clear of all wiring and hoses.
While lowering the engine assembly from the vehicle, do not allow it to contact the vehicle.
39.INSTALL ENGINE TO ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.
Install the engine assembly to an engine stand with the bolts.
Remove the 2 bolts and No. 1 engine hanger upper and No. 2 engine hanger.
82121
40.REMOVE ENGINE WIRE
Remove the engine wire from the engine assembly.
12361
41.REMOVE FRONT ENGINE MOUNTING INSULATOR
| *a | RH Side |
| *b | LH Side |
Remove the 2 nuts and 2 front engine mounting insulators from the 2 front engine mounting brackets.