Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.01
RM3270E _51 Engine / Hybrid System _048947 1GR-FE ENGINE MECHANICAL _0243429 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 83530 1.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 2.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 11415 3.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Remove the cylinder block water drain cock sub-assembly.


b.

Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.


Hide 11301M 4.REMOVE VVT SENSOR (for Bank 1)

Hide 11301M 5.REMOVE VVT SENSOR (for Bank 2)

Hide 11401G 6.REMOVE CRANKSHAFT POSITION SENSOR

Hide 15330B 7.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)

Hide 15340 8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)

Hide 15678A 9.REMOVE OIL CONTROL VALVE FILTER

a.
A326603C02
0.052,0.063 0.344,0.271 0.292,0.208 10 false *A 1.646,0.052 1.927,0.24 0.281,0.188 10 false *B
*A for Bank 1
*B for Bank 2


Remove the 2 unions, 2 oil control valve filters and 2 gaskets.


Hide 15601 10.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 15710 11.REMOVE OIL COOLER ASSEMBLY

Hide 15609 12.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

Hide 16323 13.REMOVE WATER INLET ASSEMBLY

Hide 16356 14.REMOVE REAR WATER BY-PASS JOINT

a.
A076534

Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.


b.

Remove the O-ring from the No. 1 water outlet pipe.


Hide 12108 15.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly.


b.

Remove the gasket from the oil filler cap sub-assembly.


Hide 12185 16.REMOVE OIL FILLER CAP HOUSING

a.

Remove the 2 nuts, oil filler cap housing and gasket.


Hide 11201 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12204 19.REMOVE PCV VALVE SUB-ASSEMBLY

Hide 11202 20.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 21.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13471 22.REMOVE CRANKSHAFT PULLEY

Hide 12101A 23.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket.


Hide 12102A 24.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 25.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 12101 26.REMOVE OIL PAN SUB-ASSEMBLY

Hide 11381 27.REMOVE ENGINE REAR OIL SEAL RETAINER

a.
A326608C01
0.344,1.146 0.344,0.927 0.344,0.927 0.615,0.635 true 0.781,0.26 0.99,0.448 0.208,0.188 10 true *a 0.292,1.188 0.5,1.375 0.208,0.188 10 true *b
*a Pry
*b Protective Tape


Remove the 5 bolts and 2 nuts.


b.

Using a screwdriver, remove the engine rear oil seal retainer by prying between the engine rear oil seal retainer and crankshaft bearing cap.

HINT:

Tape the screwdriver tip before use.



Hide 11381A 28.REMOVE REAR CRANKSHAFT OIL SEAL

a.
A326609

Using a screwdriver and hammer, tap out the rear crankshaft oil seal.

NOTICE:

Be careful not to damage the engine rear oil seal retainer.



Hide 11302 29.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16100 30.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A179596

Remove the 8 bolts, engine water pump assembly and gasket.


Hide 11324 31.REMOVE TIMING CHAIN COVER PLATE

Hide 11303A 32.REMOVE FRONT CRANKSHAFT OIL SEAL

Hide 13540 33.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

Never rotate the crankshaft with the No. 1 chain tensioner assembly removed.

·

When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from TDC first.



a.
A158627C01
0.906,1.26 0.906,1.771 false 2.531,1.281 2.531,1.802 false 0.833,1.792 1.042,1.979 0.208,0.188 10 false *b 2.448,1.833 2.677,2.031 0.229,0.198 10 false *b 1.469,0.771 1.667,0.958 0.198,0.188 10 true *a
*a Push
*b Stopper Plate


While turning the stopper plate of the No. 1 chain tensioner assembly clockwise, push in the plunger of the No. 1 chain tensioner assembly as shown in the illustration.


b.

While turning the stopper plate of the No. 1 chain tensioner assembly counterclockwise, insert a bar with a diameter of 3.5 mm (0.138 in.) into the holes in the stopper plate and No. 1 chain tensioner assembly to fix the stopper plate in place.


c.

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 34.REMOVE CHAIN TENSIONER SLIPPER

Hide 13530 35.REMOVE IDLE SPROCKET ASSEMBLY

a.
A326611

Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.


Hide 13562 36.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A326612

Remove the 2 No. 2 chain vibration dampers.


Hide 13506 37.REMOVE CHAIN SUB-ASSEMBLY

Hide 13521 38.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A326613

Remove the crankshaft timing sprocket.


Hide 13561 39.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A326614

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 40.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A316657C01
2.135,1.156 2.365,1.344 0.229,0.188 10 true *a
*a Raise


While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 2 chain tensioner assembly in place.


b.
A326615

Hold the hexagonal portion of the No. 2 camshaft with a wrench and remove the 2 bolts, camshaft timing gear sub-assembly, camshaft timing sprocket and No. 2 chain sub-assembly.

NOTICE:
·

Do not damage the surrounding parts.

·

Do not disassemble the camshaft timing gear sub-assembly.




Hide 13550 41.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A326616

Remove the bolt and No. 2 chain tensioner assembly.


Hide 42.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

a.
A316671C01
1.99,0.177 2.302,0.333 0.313,0.156 10 false *a
*a Push


While raising the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 3 chain tensioner assembly in place.


b.
A218533

Hold the hexagonal portion of the No. 4 camshaft sub-assembly with a wrench and remove the 2 bolts, camshaft timing gear sub-assembly, camshaft timing sprocket and No. 2 chain sub-assembly.

NOTICE:
·

Do not damage the surrounding parts.

·

Do not disassemble the camshaft timing gear sub-assembly.




Hide 13560A 43.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A326617

Remove the bolt and No. 3 chain tensioner assembly.


Hide 44.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, make sure the following steps are carried out.


a.
A326618

Rotate the camshaft and No. 2 camshaft counterclockwise and set the camshaft and No. 2 camshaft as shown in the illustration.


b.
A346195N01
1.063,1.938 1.198,2.125 0.135,0.188 10 false 1 0.563,1.115 0.677,1.292 0.115,0.177 10 true 2 0.573,0.427 0.688,0.604 0.115,0.177 10 true 3 1.063,1.24 1.177,1.417 0.115,0.177 10 true 4 1.833,1.917 1.948,2.094 0.115,0.177 10 true 5 1.323,1.115 1.438,1.292 0.115,0.177 10 true 6 1.333,0.417 1.448,0.594 0.115,0.177 10 true 7 1.823,1.229 1.938,1.406 0.115,0.177 10 true 8 3.135,1.833 3.25,2.01 0.115,0.177 10 true 9 3.177,1.25 3.396,1.438 0.219,0.188 10 true 10 3.115,0.354 3.333,0.542 0.219,0.188 10 true 11 3.167,1 3.385,1.188 0.219,0.188 10 true 12 2.49,1.927 2.708,2.115 0.219,0.188 10 true 13 2.021,1.125 2.198,1.302 0.177,0.177 10 true 14 2.021,0.448 2.198,0.625 0.177,0.177 10 true 15 2.531,1.24 2.708,1.417 0.177,0.177 10 true 16

Uniformly loosen the 16 bolts in the sequence shown in the illustration and remove the bolts and 8 camshaft bearing caps.


Hide 13511 45.REMOVE CAMSHAFT

Hide 13512 46.REMOVE NO. 2 CAMSHAFT

Hide 11811 47.REMOVE NO. 1 CAMSHAFT BEARING

A158703

Hide 11821 48.REMOVE NO. 2 CAMSHAFT BEARING

A158539

Hide 49.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
A346196N01
2.417,1.938 2.552,2.104 0.135,0.167 10 true 1 2.865,1.188 3,1.354 0.135,0.167 10 true 2 2.813,0.344 2.958,0.49 0.146,0.146 10 true 3 2.396,1.25 2.51,1.438 0.115,0.188 10 true 4 1.656,1.927 1.771,2.115 0.115,0.188 10 true 5 2.115,1.083 2.229,1.271 0.115,0.188 10 true 6 2.115,0.479 2.229,0.667 0.115,0.188 10 true 7 1.615,1.24 1.729,1.427 0.115,0.188 10 true 8 0.177,1.688 0.292,1.875 0.115,0.188 10 true 9 0.115,1.271 0.281,1.458 0.167,0.188 10 true 10 0.115,0.583 0.281,0.771 0.167,0.188 10 true 11 0.094,1.021 0.26,1.208 0.167,0.188 10 true 12 0.906,1.948 1.073,2.135 0.167,0.188 10 true 13 1.354,0.979 1.521,1.167 0.167,0.188 10 true 14 1.344,0.302 1.51,0.49 0.167,0.188 10 true 15 0.865,1.24 1.031,1.427 0.167,0.188 10 true 16

Uniformly loosen the 16 bolts in the sequence shown in the illustration and remove the bolts and 8 camshaft bearing caps.


Hide 13053 50.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

Hide 13054 51.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

Hide 11101 52.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 53.REMOVE CYLINDER HEAD GASKET

Hide 11116 55.REMOVE NO. 2 CYLINDER HEAD GASKET

Hide 16332 56.REMOVE NO. 1 WATER OUTLET PIPE

a.
A076246

Remove the knock sensor wire.


b.

for Type A:

Remove the 3 bolts and No. 1 water outlet pipe.


c.

for Type B:

Remove the bolt, 2 nuts and No. 1 water outlet pipe.


Hide 13751 58.REMOVE VALVE LIFTER

a.

Remove the 24 valve lifters.

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.



Hide 59.REMOVE TAPER SCREW PLUG

NOTICE:

It is not necessary to remove a taper screw plug unless it is being replaced.


Hide 60.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.