Home › Engine / Hybrid System › 1GR-FE LUBRICATION › OIL PUMP › from 2016.01
RM3270E _51 Engine / Hybrid System _048952 1GR-FE LUBRICATION _0243451 OIL PUMP A

1GR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11302 1.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the timing chain cover sub-assembly, cylinder head LH, cylinder head sub-assembly and cylinder block sub-assembly.


b.
A134563

Install a new O-ring to the cylinder head LH as shown in the illustration.


c.
A302593C02
0.656,1.563 1.448,1.563 1.448,1.563 1.448,1.021 true 2.313,1.563 1.74,1.563 1.74,1.563 1.74,1.021 true 0.656,1.979 0.656,1.479 true 2.313,1.948 2.313,1.375 true 0.583,2 0.896,2.198 0.313,0.198 10 true *a 2.26,1.979 2.573,2.177 0.313,0.198 10 true *a
*a Seal Packing Application Area


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)



d.

Apply seal packing as shown in the illustration.

A302594C02
5.76,1.365 5.698,1.281 5.698,1.281 5.521,1.281 false 6.396,1.375 6.479,1.281 6.479,1.281 6.688,1.281 false 3.854,1.031 3.948,0.354 3.948,0.354 2.552,0.521 true 2.26,2.115 1.063,2.375 1.063,2.375 2.354,1.719 true 1.51,2.615 1.073,2.375 1.073,2.375 1.854,2.104 true 3.917,1.917 3.688,1.917 3.688,1.917 3.438,1.917 true 1.073,1.813 0.844,1.813 0.844,1.813 0.594,1.813 true 0.875,2.302 1.188,2.458 0.313,0.156 10 false *a 3.021,3.323 3.333,3.479 0.313,0.156 10 false *d 5.031,2.917 5.344,3.073 0.313,0.156 10 false *b 5.031,3.094 5.344,3.25 0.313,0.156 10 false *c 5.896,0.844 6.354,1.01 0.458,0.167 10 false B - B 6.792,1.698 7.042,1.938 0.25,0.24 10 false *d 5.344,1.198 5.656,1.354 0.313,0.156 10 false *a 6.74,1.198 7.052,1.354 0.313,0.156 10 false *a 6.021,2.167 6.333,2.469 0.313,0.302 10 false *e 3.948,0.188 4.26,0.344 0.313,0.156 10 false *a 0.99,0.865 1.146,1.063 0.156,0.198 10 false A 1.354,1.344 1.51,1.542 0.156,0.198 10 false B 1.01,1.49 1.167,1.688 0.156,0.198 10 false B 3.969,1.833 4.281,1.99 0.313,0.156 10 false *a 0.417,1.719 0.729,1.875 0.313,0.156 10 false *a 5.271,1.677 5.521,1.917 0.25,0.24 10 false *d
*a Seal Packing *b Continuous line area
*c Dashed line area *d 3.0 to 4.0 mm (0.118 to 0.157 in.)
*e 16.7 mm (0.657 in.) - -


Seal packing:
Continuous line area:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Dashed line area:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)


NOTICE:
·

Install the timing chain cover sub-assembly within 3 minutes after applying seal packing. After installing it, the bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

·

Do not apply seal packing to "A" shown in the illustration.




e.
A343641C01
0.615,0.51 0.615,0.177 0.615,0.177 1.031,0.177 true 1.073,0.104 1.385,0.302 0.313,0.198 10 false *a
*a 15°


Align the width of the joint portion of the oil pump drive rotor and the crankshaft timing gear, and then install the timing chain cover sub-assembly.


f.
A251902C01
0.323,1.177 0.396,1.156 false
V100135

Bolt A
V100136

Bolt B
V100137

Nut


Install the timing chain cover sub-assembly with the 24 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
for bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for nut : 23 N*m (235 kgf*cm, 17 ft.*lbf)

Standard Bolt:
Item Length
Bolt A 25 mm (0.984 in.)
Bolt B 55 mm (2.17 in.)


NOTICE:
·

Make sure not to wrap the chain and slipper over the timing chain cover seal line.

·

Make sure that there is no oil on the bolt threads.




Hide 15609 3.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

a.

Install a new gasket and the oil filter bracket sub-assembly with the 3 bolts and 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 15601 4.INSTALL OIL FILTER SUB-ASSEMBLY

Hide 11202 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.

Clean and degrease the contact surfaces of the timing chain cover sub-assembly and cylinder head LH.


b.
A343642C01
0.75,1.833 1.333,2 1.333,2 1.583,2 true 0.729,0.521 0.729,0.271 0.729,0.271 0.563,0.271 true 1.615,1.917 1.927,2.115 0.313,0.198 10 false *a 0.385,0.177 0.698,0.375 0.313,0.198 10 false *a
*a Seal Packing Application Area


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:

Install the cylinder head cover sub-assembly LH within 3 minutes after applying seal packing. After installing it, the bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.



c.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly LH.


d.

Install new seal washers to the bolts.


e.
A343643C01
2.188,1.802 2.344,2 0.156,0.198 10 false .
V100135

Bolt A
V100136

Bolt B
V100137

Nut


Temporarily install the cylinder head cover sub-assembly LH with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B and nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)

Standard Bolt:
Item Length
Bolt A 25 mm (0.984 in.)
Bolt B 60 mm (2.36 in.)



Hide 11201 6.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the timing chain cover sub-assembly and cylinder head sub-assembly.


b.
A343644C01
2.74,0.51 2.74,0.177 2.74,0.177 2.99,0.177 true 2.74,1.854 2.417,2 2.417,2 2.25,2 true 3.042,0.094 3.354,0.292 0.313,0.198 10 false *a 2.021,1.906 2.219,2.083 0.198,0.177 10 true *a
*a Seal Packing Application Area


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:

Install the cylinder head cover sub-assembly within 3 minutes after applying seal packing. After installing it, bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.



c.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.


d.

Install new seal washers to the bolts.


e.
A343645C01
1.24,1.76 1.396,1.958 0.156,0.198 10 false .
V100135

Bolt A
V100136

Bolt B
V100137

Nut


Temporarily install the cylinder head cover sub-assembly with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B and nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)

Standard Bolt Length:
Item Specified Condition
Bolt A 25 mm (0.984 in.)
Bolt B 60 mm (2.36 in.)



Hide 23801P 7.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY AND NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 12101 8.INSTALL OIL PAN SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the cylinder block, rear oil seal retainer and oil pan sub-assembly.


b.

Install a new O-ring to the timing chain cover sub-assembly.


c.
A343646C01
2.76,2.01 2.51,2.01 2.51,2.01 2.51,1.594 true 2.802,1.938 3.115,2.135 0.313,0.198 10 false *a
*a Seal Packing Application Area


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes after applying seal packing. After installing the oil pan sub-assembly, the bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

·

Do not start the engine for at least 2 hours after installing.




d.
A354823C01
2.25,1.083 2.583,0.667 true 2.25,1.083 2.583,0.948 true 2.25,1.083 2.583,1.26 true 2.25,1.083 2.583,1.583 true 2.25,1.083 2.094,1.667 true 2.083,1.083 2.25,1.083 false 1.917,1 2.073,1.198 0.156,0.198 10 true ★
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Nut


Install the oil pan sub-assembly with the 17 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
except bolt C : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt C : 10 N*m (102 kgf*cm, 7 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Standard Bolt:
Item Length
Bolt A 25 mm (0.984 in.)
Bolt B 45 mm (1.77 in.)
Bolt C 16 mm (0.630 in.)


NOTICE:

The bolts indicated by stars in the illustration are precoated parts. When reusing these bolts, apply adhesive to 2 or 3 threads before installation.



Hide 15104 9.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer sub-assembly with the bolt and 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 12102A 10.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.


b.
A251904C02
2.417,1.448 2.875,1.448 true 2.875,1.365 3.104,1.552 0.229,0.188 10 false *a
*a Seal Packing Application Area


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan sub-assembly within 3 minutes after applying seal packing. After installing the No. 2 oil pan, the bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

·

Do not start the engine for at least 4 hours after the installation.




c.

Install the No. 2 oil pan sub-assembly with the 14 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
for bolt : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
for nut : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13471 11.INSTALL CRANKSHAFT PULLEY

a.

Align the key groove of the crankshaft pulley with the pulley set key and slide on the crankshaft pulley.


b.
A343647C01
0.333,0.417 0.583,0.417 0.583,0.417 1.25,1.083 true 1.167,0.75 0.583,0.417 false 0.052,0.344 0.51,0.542 0.458,0.198 10 false SST 2.792,1.052 3.25,1.25 0.458,0.198 10 false *a 1.948,1.969 2.406,2.167 0.458,0.198 10 false *b
*a Hold
*b Turn


Using SST, install the crankshaft pulley with the crankshaft pulley set bolt.

SST
09213-54015  (91651-60855)
09330-00021  

Torque:
250 N*m (2549 kgf*cm, 184 ft.*lbf)


Hide 16603 12.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16604 13.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 14.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16031 15.INSTALL WATER INLET ASSEMBLY

Hide 11452 16.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15340 18.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)

Hide 15330B 19.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)