Home › Drivetrain › RC61F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › from 2016.01
RM3270E _52 Drivetrain _041683 RC61F MANUAL TRANSMISSION / TRANSAXLE _0201477 MANUAL TRANSMISSION ASSEMBLY A

RC61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C03
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 33504F 3.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

a.

Remove the shift lever knob sub-assembly from the shift lever.


Hide 58810J 4.REMOVE CONSOLE BOX ASSEMBLY

Hide 58280A 5.REMOVE SHIFT LEVER BOOT ASSEMBLY

a.
C324629

Remove the 6 screws, 4 clips and shift lever boot assembly.


Hide 33530F 6.REMOVE SHIFT LEVER ASSEMBLY

a.
C332406

Detach the shift lever cap boot from the manual transmission.


b.

Cover the shift lever cap with a cloth.


c.
C353574C01
1.865,0.99 2,1.24 2,1.24 2.458,1.24 true 2.521,1.156 2.833,1.354 0.313,0.198 10 false *1
*1 Shift Lever Cap
V113147

Press Down
V113148

Counterclockwise
V113149

Pull Out


While pressing down on the shift lever cap, turn it counterclockwise, and then pull to remove the shift lever.


Hide 33548F 7.REMOVE NO. 1 FLOOR SHIFT BUSH

a.
C329824

Remove the No. 1 floor shift bush from the shift lever assembly.


Hide 51410 9.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 10.REMOVE NO. 2 ENGINE UNDER COVER

Hide 51561D 11.REMOVE PROPELLER SHAFT GUARD

a.
C324638

Remove the propeller shaft guard with the 2 bolts.


Hide 17410 12.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 28100 13.REMOVE STARTER ASSEMBLY (for 1KD-FTV)

Hide 12584 15.REMOVE NO. 4 CYLINDER BROCK INSULATOR

a.

Remove the No. 4 cylinder block insulator.


Hide 33119 16.REMOVE STIFFENER PLATE LH

a.
C324648

Remove the 4 bolts and stiffener plate LH.


Hide 33118 17.REMOVE STIFFENER PLATE RH

a.
C325402

Remove the 4 bolts and stiffener plate RH.


Hide 37100 18.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 41110F 19.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

Hide 20.DISCONNECT GROUND CABLE

a.
C335926

Remove the bolt and disconnect the ground cable.


Hide 21.SUPPORT MANUAL TRANSMISSION ASSEMBLY

a.
C324639

Support the manual transmission with a transmission jack.

NOTICE:
·

Make sure the high transmission jack attachment is centered on the safety stand.

·

Secure the part with a rope, attachment, etc.




Hide 51204 22.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C338961

Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.


b.
C325680

Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.


Hide 12371A 23.REMOVE REAR ENGINE MOUNTING INSULATOR

a.
C324651

Remove the 4 bolts and rear engine mounting insulator from the manual transmission assembly.


Hide 24.DISCONNECT WIRE HARNESS

a.

w/ Downhill Assist Control:

i.
C344347

Disconnect the neutral position switch conector.



b.
C328313

w/ Intelligent Manual Transmission Switch:

i.

Detach the 7 wire harness clamps.


ii.

Remove the bolt.


iii.

Disconnect the 3 connectors and wire harness.



c.
C328312

w/o Intelligent Manual Transmission Switch:

i.

Detach the 5 wire harness clamps.


ii.

Remove the bolt.


iii.

Disconnect the 2 connectors and wire harness.



Hide 25.REMOVE MANUAL TRANSMISSION ASSEMBLY

a.
C324649

Remove the 5 bolts and manual transmission assembly.

NOTICE:

As the manual transmission assembly is very heavy, be sure to support it securely.



Hide 33019C 26.REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY

a.
C324643

Detach the 4 breather hose clamps and bracket.


b.

Remove the transmission breather sub-assembly from the control shift lever retainer assembly.


c.
C324647

Remove the 2 bolts and 2 brackets.


Hide 27.REMOVE WIRING HARNESS CLAMP BRACKET

a.
C324646

w/ Intelligent Manual Transmission Switch:

i.

Remove the 8 bolts and 7 wiring harness clamp brackets.



b.
C329814

w/o Intelligent Manual Transmission Switch:

i.

Remove the 7 bolts and 6 wiring harness clamp brackets.