Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › from 2016.08
RM3270E _58 Vehicle Interior _041713 HEATING / AIR CONDITIONING _0205065 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turns the magnet clutch on based on this signal.

WIRING DIAGRAM

except 5L-E:
E315708E48
5.208,3.385 5.667,3.583 0.458,0.198 10 false G131 5.219,3.552 6.792,4.01 1.573,0.458 10 false Air Conditioning Amplifier Assembly 5.417,1.604 5.875,1.802 0.458,0.198 10 false AC1 5.427,0.885 5.885,1.083 0.458,0.198 10 false ACT 5.427,2.542 5.885,2.74 0.458,0.198 10 false MGC 0.813,1.708 1.271,1.906 0.458,0.198 10 false AC1 0.813,0.979 1.271,1.177 0.458,0.198 10 false ACT 5.125,1.604 5.583,1.802 0.458,0.198 10 false 12 5.115,0.885 5.573,1.083 0.458,0.198 10 false 18 1.208,0.885 2.719,1.094 1.51,0.208 10 false 24*1, 14*2, 19*3 1.208,1.594 2.719,1.802 1.51,0.208 10 false 30*1, 15*2, 18*3 5.125,2.542 5.583,2.74 0.458,0.198 10 false 16 4.51,2.542 4.969,2.74 0.458,0.198 10 false 1 3.313,2.542 3.771,2.74 0.458,0.198 10 false 2 3.302,2.948 3.76,3.146 0.458,0.198 10 false 5 4.521,2.948 4.979,3.146 0.458,0.198 10 false 3 3.635,3.385 5.083,3.635 1.448,0.25 10 false A/C COMP 4.802,3.99 5.26,4.188 0.458,0.198 10 false 1 3.781,4.25 4.688,4.635 0.906,0.385 10 false Magnet Clutch Assembly*4 2.813,4.979 4.448,5.229 1.635,0.25 10 false C3 2.813,5.125 5.479,5.375 2.667,0.25 10 false Compressor Assembly with Magnet Clutch 0.354,2.229 2.26,2.438 1.906,0.208 10 false G143*1, G50*2, G140*3 0.365,2.385 0.823,2.583 0.458,0.198 10 false ECM 0.583,2.646 2.406,2.875 1.823,0.229 10 false from HTR Relay 4.375,3.99 4.833,4.188 0.458,0.198 10 false MG+ 2.313,2.813 3.198,3.031 0.885,0.219 10 false A/C 5.958,0.74 6.417,0.938 0.458,0.198 10 false 5 V 6.229,1.406 6.688,1.604 0.458,0.198 10 false IC 0.083,4.948 2.333,5.198 2.25,0.25 10 false *2: for 1GD-FTV, 2GD-FTV 0.083,5.229 2.333,5.479 2.25,0.25 10 false *3: for 1KD-FTV, 2KD-FTV 0.083,4.656 2.333,4.906 2.25,0.25 10 false *1: for 2TR-FE 0.094,5.521 2.344,5.771 2.25,0.25 10 false *4: w/ Magnet Clutch Assembly

for 5L-E:
E342777E06
5.938,0.719 6.396,0.917 0.458,0.198 10 false 5 V 5.406,0.885 5.865,1.083 0.458,0.198 10 false ACT 5.417,1.604 5.875,1.802 0.458,0.198 10 false AC1 5.427,2.542 5.885,2.74 0.458,0.198 10 false MGC 5.104,0.885 5.563,1.083 0.458,0.198 10 false 18 5.125,1.604 5.583,1.802 0.458,0.198 10 false 12 5.115,2.542 5.573,2.74 0.458,0.198 10 false 16 5.188,3.344 5.646,3.542 0.458,0.198 10 false G131 5.188,3.51 6.781,3.948 1.594,0.438 10 false Air Conditioning Amplifier Assembly 3.646,3.406 4.896,3.615 1.25,0.208 10 false A/C COMP 4.521,2.542 4.979,2.74 0.458,0.198 10 false 1 3.302,2.542 3.76,2.74 0.458,0.198 10 false 2 3.302,2.948 3.76,3.146 0.458,0.198 10 false 5 4.531,2.948 4.99,3.146 0.458,0.198 10 false 3 2.302,2.813 3.552,3.021 1.25,0.208 10 false A/C 0.583,2.646 1.833,2.854 1.25,0.208 10 false from HTR Relay 0.594,2.25 1.844,2.458 1.25,0.208 10 false ECM 0.802,0.979 1.26,1.177 0.458,0.198 10 false ACT 0.813,1.729 1.271,1.927 0.458,0.198 10 false AC1 4.385,4 4.844,4.198 0.458,0.198 10 false MG+ 4.833,3.99 5.292,4.188 0.458,0.198 10 false 1 2.813,4.948 4.063,5.156 1.25,0.208 10 false C3 2.823,5.125 5.729,5.385 2.906,0.26 10 false Compressor Assembly with Magnet Clutch 1.208,1 1.667,1.198 0.458,0.198 10 false G161 1.323,0.76 1.781,0.958 0.458,0.198 10 false 9 1.219,1.719 1.677,1.917 0.458,0.198 10 false G160 1.302,1.49 1.76,1.688 0.458,0.198 10 false 34 6.229,1.396 6.688,1.615 0.458,0.219 10 false IC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (A/C SIGNAL)
a.

Use the Data List to check if the magnet clutch on request signal is functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/C Signal Magnet clutch on request signal ON or OFF ON: "A/C" switch on
OFF: "A/C" switch off
Operates with the engine idling and the blower switch on (LO level).
Powertrain > Engine and ECT > Data List
Tester Display
A/C Signal
50003 234 152
OK:

Display is as specified in normal condition.



Result:
Proceed to
OK
NG



OK

2.INSPECT MAGNET CLUTCH RELAY (A/C COMP)

NG

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
2.INSPECT MAGNET CLUTCH RELAY (A/C COMP)
a.

Remove the A/C COMP relay from the No. 4 instrument panel relay block assembly.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

REPLACE MAGNET CLUTCH RELAY (A/C COMP RELAY)

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
a.

Disconnect the air conditioning amplifier assembly connector.


b.
B409698C06
0.167,1.063 0.667,1.313 0.5,0.25 2.573,1.896 2.24,1.896 2.24,1.896 1.875,1.292 true 0.24,1.104 0.698,1.302 0.458,0.198 10 false G131 0.063,0.031 0.521,0.229 0.458,0.198 10 false *a 2.625,1.802 3.083,2 0.458,0.198 10 false MGC
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G131-16 (MGC) - Body ground Ignition switch off Below 1 V
G131-16 (MGC) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.
E322922C07
1.438,0.354 1.938,0.604 0.5,0.25 1.875,1.313 2.104,2.031 2.104,2.031 2.354,2.031 true 1.521,0.396 2.135,0.594 0.615,0.198 10 false G131 2.406,1.948 3.021,2.146 0.615,0.198 10 true MGC
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G131-16 (MGC) - Body ground
·

Engine running

·

Blower switch: LO or higher

·

"A/C" switch: Off or on (magnet clutch off)


Below 1 V
G131-16 (MGC) - Body ground
·

Engine running

·

Blower switch: LO or higher

·

"A/C" switch: On (magnet clutch on)


11 to 14 V



Result:
Result Proceed to
OK (w/ Magnet Clutch Assembly) A
OK (w/o Magnet Clutch Assembly) B
NG C



A

5.INSPECT MAGNET CLUTCH ASSEMBLY

B

6.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY - COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH AND BATTERY)

C

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY - COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH AND BATTERY)
a.

Remove the magnet A/C COMP relay assembly from the No. 4 instrument panel junction block assembly.


b.

Disconnect the C3 compressor assembly with magnet clutch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - C3-1 (MG+) Always Below 1 Ω
Relay terminal 3 or C3-1 (MG+) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Relay terminal 5 - Body ground Ignition switch off Below 1 V
Relay terminal 5 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
a.

Disconnect the G131 air conditioning amplifier assembly connector.


b.

except 5L-E:

i.

Disconnect the G143*1, G50*2 or G140*3 ECM connector.

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1KD-FTV, 2KD-FTV




c.

for 5L-E:

i.

Disconnect the G160 and G161 ECM connectors.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE:
Tester Connection Condition Specified Condition
G131-12 (AC1) - G143-30 (AC1) Always Below 1 Ω
G131-18 (ACT) - G143-24 (ACT) Always Below 1 Ω
G131-12 (AC1) or G143-30 (AC1) - Body ground Always 10 kΩ or higher
G131-18 (ACT) or G143-24 (ACT) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV:
Tester Connection Condition Specified Condition
G131-12 (AC1) - G50-15 (AC1) Always Below 1 Ω
G131-18 (ACT) - G50-14 (ACT) Always Below 1 Ω
G131-12 (AC1) or G50-15 (AC1) - Body ground Always 10 kΩ or higher
G131-18 (ACT) or G50-14 (ACT) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV:
Tester Connection Condition Specified Condition
G131-12 (AC1) - G140-18 (AC1) Always Below 1 Ω
G131-18 (ACT) - G140-19 (ACT) Always Below 1 Ω
G131-12 (AC1) or G140-18 (AC1) - Body ground Always 10 kΩ or higher
G131-18 (ACT) or G140-19 (ACT) - Body ground Always 10 kΩ or higher

for 5L-E:
Tester Connection Condition Specified Condition
G131-12 (AC1) - G160-34 (AC1) Always Below 1 Ω
G131-18 (ACT) - G161-9 (ACT) Always Below 1 Ω
G131-12 (AC1) or G160-34 (AC1) - Body ground Always 10 kΩ or higher
G131-18 (ACT) or G161-9 (ACT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.
E322922C08
1.49,0.365 1.99,0.615 0.5,0.25 2.406,1.313 2.656,1.729 2.656,1.729 2.906,1.729 true 1.552,0.417 2.167,0.615 0.615,0.198 10 false G131 2.948,1.646 3.406,2 0.458,0.354 10 true AC1
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G131-12 (AC1) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: On


Below 1 V
G131-12 (AC1) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: Off


11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
a.

Disconnect the G131 air conditioning amplifier assembly connector.


b.

Disconnect the G143*1, G50*2, G140*3 or G161*4 ECM connector.

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1KD-FTV, 2KD-FTV

*4: for 5L-E



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE:
Tester Connection Condition Specified Condition
G131-18 (ACT) - G143-24 (ACT) Always Below 1 Ω
G131-18 (ACT) or G143-24 (ACT) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV:
Tester Connection Condition Specified Condition
G131-18 (ACT) - G50-14 (ACT) Always Below 1 Ω
G131-18 (ACT) or G50-14 (ACT) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV:
Tester Connection Condition Specified Condition
G131-18 (ACT) - G140-19 (ACT) Always Below 1 Ω
G131-18 (ACT) or G140-19 (ACT) - Body ground Always 10 kΩ or higher

for 5L-E:
Tester Connection Condition Specified Condition
G131-18 (ACT) - G161-9 (ACT) Always Below 1 Ω
G131-18 (ACT) or G161-9 (ACT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK ECM
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.
E322922C09
1.49,0.365 1.99,0.615 0.5,0.25 1.688,1.302 2.073,2.031 2.073,2.031 2.323,2.031 true 1.563,0.417 2.177,0.615 0.615,0.198 10 false G131 2.385,1.938 2.833,2.146 0.448,0.208 10 true ACT
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G131-18 (ACT) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: Off or on (magnet clutch off)


Below 1 V
G131-18 (ACT) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: On (magnet clutch on)


4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG