Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2111  Throttle Actuator Control System - Stuck Open  P2112  Throttle Actuator Control System - Stuck Closed  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body. The throttle position sensor provides feedback to the ECM so that the ECM can control the throttle actuator (throttle valve) appropriately in response to driver inputs.

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2111 Throttle Actuator Control System - Stuck Open Throttle actuator does not close even when the ECM commands it to close (1 trip detection logic).
·

Throttle actuator

·

Throttle valve

·

Throttle body with motor assembly

·

Wire harness or connector


Comes on DTC stored
P2112 Throttle Actuator Control System - Stuck Closed Throttle actuator does not open even when the ECM commands it to open (1 trip detection logic).
·

Throttle actuator

·

Throttle valve

·

Throttle body with motor assembly

·

Wire harness or connector


Comes on DTC stored

MONITOR DESCRIPTION

The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored when the accelerator pedal is fully depressed and released quickly (to fully open and close the throttle valve) after the engine is next started.

MONITOR STRATEGY

Required Sensors/Components Throttle actuator
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

All
Throttle actuator ON
Throttle actuator duty calculation Executing
Throttle position sensor failure Not detected
Throttle actuator current-cut operation Not executing
Throttle actuator power supply 4 V or higher
Throttle actuator failure Not detected

P2111 (Throttle Actuator Stuck Open)
All of following conditions met -
Throttle actuator current 2 A or higher
Duty cycle to close throttle 80% or more

P2112 (Throttle Actuator Stuck Closed)
All of following conditions met -
Throttle actuator current 2 A or higher
Duty cycle to open throttle 80% or more

TYPICAL MALFUNCTION THRESHOLDS

Throttle position sensor voltage No change

CONFIRMATION DRIVING PATTERN

A199314
0.104,0.052 1.615,0.229 1.51,0.177 10 false Accelerator Pedal State 0.927,0.385 1.656,0.531 0.729,0.146 10 false Depressed 0.938,0.875 1.583,1.031 0.646,0.156 10 false Released 1.208,2.323 1.594,2.51 0.385,0.188 10 false Idling 0.406,2.604 1.615,2.771 1.208,0.167 10 false Ignition Switch ON 2.073,2.698 2.375,2.969 0.302,0.271 10 false [A] 4.396,3.427 4.667,3.656 0.271,0.229 10 false [B]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).

7.

Enter the following menus: Powertrain / Engine and ECT / DTC [B].

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P2111 or P2112.

11.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



12.

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again and, if necessary, drive the vehicle for a period of time.


Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

FAIL-SAFE

When either of these DTCs or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)] (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P2111 or P2112 is output A
P2111 or P2112 and other DTCs are output B


HINT:

If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.




A

2.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

B

2.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for contamination between the throttle valve and housing. If necessary, clean the throttle body. Also, check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)

NG

5.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
3.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

Powertrain > Engine > Data List
Tester Display
Throttle Position No.1
Throttle Position No.2
Throttle Position Command
50003 61 112,113,125

h.

Check the values displayed on the intelligent tester while wiggling the ECM wire harness.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Check for DTCs.

Result:
Result Proceed to
Value in Data List changes when wire harness is wiggled, or DTC is output A
Other than above B




A

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY WITH MOTOR)

B

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY WITH MOTOR)
a.

As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


Result:
Proceed to
NEXT



NEXT

END

5.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Replace the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

e.

Start the engine, and then fully depress and release the accelerator pedal quickly to fully open and close the throttle valve.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
P2111 or P2112 is output B




A

END

B