Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET
RM1880E _51 Engine / Hybrid System _013210 2TR-FE ENGINE MECHANICAL _0068467 CYLINDER HEAD GASKET A

2TR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 3.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A302540C01
1.385,3.823 1.563,3.26 1.563,3.26 1.74,3.26 true 0.969,2.083 0.76,1.875 0.76,1.875 0.583,1.875 true 1.167,3.906 1.344,3.323 1.344,3.323 1.156,3.323 true 2.01,2.302 1.927,1.802 1.927,1.802 1.76,1.802 true 0.948,0.854 1.052,1.448 1.052,1.448 1.375,1.448 true 1.073,0.656 1.208,1.448 true 2.75,0.917 3.083,0.302 true 2.74,0.656 2.948,0.313 2.948,0.313 3.146,0.313 true 1.823,3.156 2.135,3.313 0.313,0.156 10 false *1 0.969,3.229 1.281,3.385 0.313,0.156 10 false *2 0.396,1.771 0.708,1.927 0.313,0.156 10 false *1 1.573,1.698 1.885,1.854 0.313,0.156 10 false *1 1.427,1.333 1.74,1.49 0.313,0.156 10 false *1 0.844,0.125 1.333,0.302 0.49,0.177 10 false 13°47' 2.625,0.125 3.063,0.333 0.438,0.208 10 false 6°37' 3.146,0.198 3.385,0.354 0.24,0.156 10 false *1
*1 Timing Mark
*2 Key


Temporarily install the crankshaft pulley bolt.


b.

Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



c.

Remove the crankshaft pulley bolt.


Hide 5.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
A101303C07
1.854,1.531 2.104,1.708 2.104,1.708 2.24,1.708 true 2.323,0.781 2.552,0.344 2.552,0.344 2.677,0.344 true 0.563,1.854 0.563,1.521 false 2.26,1.615 2.49,1.792 0.229,0.177 10 false *2 0.479,1.875 0.656,2.042 0.177,0.167 10 false *3 2.729,0.25 2.906,0.417 0.177,0.167 10 false *1
*1 Plunger
*2 Stopper Plate
*3 Hexagon Wrench


·

When the chain tensioner is removed, do not rotate the crankshaft.

·

When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.



a.

Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.


c.
A101305

Remove the bolt, nut, chain tensioner and gasket.


Hide 6.REMOVE CHAIN TENSIONER SLIPPER

a.
A302541

Remove the bolt and tensioner slipper.


Hide 7.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A302542

Remove the 2 bolts and vibration damper.


Hide 8.REMOVE CHAIN SUB-ASSEMBLY

Hide 9.REMOVE CAMSHAFT BEARING CAP

a.
A170574N04
2.563,1.5 2.656,1.635 0.094,0.135 1.573,0.188 1.771,0.344 0.198,0.156 10 false 20 0.948,1.823 1.146,1.979 0.198,0.156 10 false 10 1.573,1.823 1.771,1.979 0.198,0.156 10 false 18 2.167,1.823 2.365,1.979 0.198,0.156 10 false 14 2.823,1.823 3.021,1.979 0.198,0.156 10 false 6 2.146,0.188 2.354,0.354 0.208,0.167 10 false 16 0.938,0.188 1.146,0.354 0.208,0.167 10 true 12 0.667,1.448 0.875,1.615 0.208,0.167 10 true 11 1.24,1.448 1.448,1.615 0.208,0.167 10 true 19 1.854,1.448 2.063,1.615 0.208,0.167 10 true 15 1.25,1.063 1.458,1.229 0.208,0.167 10 true 13 1.854,1.063 2.063,1.229 0.208,0.167 10 true 21 2.479,1.063 2.688,1.229 0.208,0.167 10 true 17 0.479,0.188 0.594,0.354 0.115,0.167 10 false 3 0.177,0.646 0.292,0.813 0.115,0.167 10 false 5 0.25,1.01 0.365,1.177 0.115,0.167 10 false 1 2.51,1.448 2.646,1.604 0.135,0.156 10 true 7 3.094,1.073 3.208,1.24 0.115,0.167 10 true 9 0.219,1.354 0.333,1.521 0.115,0.167 10 true 4 0.479,1.875 0.594,2.042 0.115,0.167 10 false 2 2.802,0.188 2.917,0.365 0.115,0.177 10 false 8

Uniformly loosen and remove the 21 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshafts level.



b.
A101310

Remove the oil delivery pipe and O-ring from the bearing caps.


c.
A302543

Remove the 9 bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 10.REMOVE CAMSHAFT

A101312

Hide 11.REMOVE NO. 2 CAMSHAFT

A101313

Hide 12.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 14.REMOVE VALVE STEM CAP

a.
A101315

Remove the 16 valve stem caps from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 15.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A302544N01
0.531,1.792 0.688,1.99 0.156,0.198 10 true 1 2.99,0.25 3.146,0.448 0.156,0.198 10 true 2 0.531,0.26 0.688,0.458 0.156,0.198 10 true 3 3,1.802 3.156,2 0.156,0.198 10 true 4 1.156,0.26 1.313,0.458 0.156,0.198 10 false 5 2.385,1.802 2.542,2 0.156,0.198 10 false 6 1.125,1.792 1.281,1.99 0.156,0.198 10 false 7 2.385,0.271 2.542,0.469 0.156,0.198 10 false 8 1.76,1.813 1.917,2.01 0.156,0.198 10 false 9 1.708,0.26 1.927,0.438 0.219,0.177 10 false 10

Uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

NOTICE:
·

Be careful not to drop the washers into the cylinder head.

·

Head warpage or cracking could result from removing the bolts in the wrong order.




Hide 16.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block.