1.INSTALL CRANKSHAFT PULLEY SET KEY
Install the 2 pulley set keys to the crankshaft.
2.INSTALL NO. 4 CHAIN VIBRATION DAMPER
Install the vibration damper with the 2 bolts.
3.INSTALL NO. 2 CHAIN SUB-ASSEMBLY
Install the No. 2 crankshaft timing sprocket as shown in the illustration.
Check that the No. 1 cylinder is at TDC and that the weights of the No. 1 and No. 2 balance shafts are at the bottom.
Install the timing sprocket with the front mark facing forward.
| *1 | Mark Plate (Yellow) |
| *2 | Timing Mark |
As shown in the illustration, install the chain to the sprocket and gear with the mark plates aligned with the timing marks on the sprocket and gear.
| *1 | Mark Plate (Yellow) |
| *2 | Large Timing Mark |
Fit the other mark plate of the chain behind the large timing mark of the balance shaft drive gear.
Insert the balance shaft drive gear shaft through the balance shaft drive gear so that it fits into the thrust plate hole.
| *1 | Large Timing Mark |
| *2 | Small Timing Mark |
| *3 | Mark Plate (Yellow) |
Align the small timing mark of the balance shaft drive gear with the large timing mark of the balance shaft timing gear.
Install the bolt to the balance shaft drive gear.
| *1 | Large Timing Mark |
| *2 | Small Timing Mark |
| *3 | Mark Plate (Yellow) |
| *4 | Timing Mark |
Check that each timing mark is aligned with the corresponding mark plate.
Check that the No. 1 cylinder is at TDC and that the weights of the No. 1 and No. 2 balance shafts are at the bottom.
4.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY
Install the chain tensioner assembly with the nut.
Install the chain tensioner with the pin installed, and then remove the pin after installation. When performing this step, do not push the vibration damper against the chain.
| *1 | Plunger |
| *2 | Stopper Plate |
Move the stopper plate downward to release the lock and push the plunger deep into the tensioner.
Move the stopper plate upward to set the lock and insert a hexagon wrench into the stopper plate hole.
5.INSTALL NO. 3 CHAIN VIBRATION DAMPER
Install the chain vibration damper with the 2 bolts.
6.INSTALL NO. 2 CHAIN VIBRATION DAMPER
Install the chain vibration damper with the bolt.
Remove the pin from the chain tensioner assembly to release the plunger.
7.INSTALL NO. 1 TAPER SCREW PLUG
Install the screw plug to the cylinder block.
8.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY
Using a hexagon wrench, install the oil filter bracket union.
| *1 | New O-Ring |
| *2 | New Oil Filter Bracket Gasket |
Install a new oil filter bracket gasket to the oil filter bracket.
Install a new O-ring to the oil filter bracket union.
Apply a light coat of engine oil to the O-ring and oil filter bracket.
Install 2 new gaskets and the 2 screw plugs to the oil filter bracket.
Install the oil filter bracket with the 2 bolts and nut.
Using a 27 mm socket wrench, install the oil filter union.
9.INSTALL OIL FILTER SUB-ASSEMBLY
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.
Using SST, tighten the oil filter.
10.INSTALL REAR CRANKSHAFT OIL SEAL
| *1 | Wooden Block |
Place the oil seal retainer on wooden blocks.
Apply a light coat of MP grease to the lip of a new oil seal.
Do not allow foreign matter to contact the lip of the oil seal.
Do not allow MP grease to contact the dust seal.
Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.
Wipe off any extra grease from the crankshaft.
Do not tap in the oil seal at an angle.
11.INSTALL REAR ENGINE OIL SEAL RETAINER
| *1 | Seal Packing |
Apply seal packing in a continuous bead as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.0 to 3.0 mm (0.0787 to 0.118 in.)
Remove any oil from the contact surface.
Install the rear oil seal retainer within 3 minutes after applying seal packing.
Do not start the engine for at least 4 hours after installation.
Install the oil seal retainer with the 6 bolts.
12.INSTALL OIL CONTROL VALVE FILTER
Check that no foreign matter is on the mesh part of the filter.
If foreign matter is present, clean the part thoroughly.
Using an 8 mm hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.
13.INSTALL CYLINDER HEAD GASKET
14.INSTALL CYLINDER HEAD SUB-ASSEMBLY
15.INSTALL CAMSHAFT TIMING SPROCKET
Mount the camshaft in a vise and install the camshaft timing sprocket to the camshaft with the sprocket bolt.
Do not damage the camshaft in the vise.
16.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
17.INSTALL VALVE LASH ADJUSTER ASSEMBLY
18.INSTALL VALVE STEM CAP
19.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
20.INSTALL CAMSHAFT
21.INSTALL CAMSHAFT BEARING CAP
22.INSTALL CRANKSHAFT TIMING SPROCKET
Install the timing sprocket as shown in the illustration.
23.INSTALL NO. 1 CHAIN VIBRATION DAMPER
24.INSTALL CHAIN SUB-ASSEMBLY
25.INSTALL CHAIN TENSIONER SLIPPER
26.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
27.INSTALL TIMING CHAIN GUIDE
28.INSTALL ENGINE WATER PUMP ASSEMBLY
29.INSTALL OIL PUMP RELIEF VALVE
30.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
31.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
32.INSTALL FRONT CRANKSHAFT OIL SEAL
33.INSTALL OIL PAN STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
Using E5 and E7 "TORX" socket wrenches, install the stud bolts.
34.INSTALL OIL PAN SUB-ASSEMBLY
35.INSTALL OIL STRAINER SUB-ASSEMBLY
36.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
37.INSTALL CRANKSHAFT PULLEY
38.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
39.INSTALL THERMOSTAT
40.INSTALL WATER INLET
41.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
42.INSTALL CRANKSHAFT POSITION SENSOR
43.INSTALL CAMSHAFT POSITION SENSOR
44.INSTALL PCV VALVE SUB-ASSEMBLY
45.INSTALL OIL FILLER CAP SUB-ASSEMBLY
Install the gasket to the oil filler cap.
Install the oil filler cap.
46.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
47.INSTALL KNOCK SENSOR
48.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
49.INSTALL SPARK PLUG