Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE
RM1880E _54 Brake _013230 PARKING BRAKE _0068575 PARKING BRAKE CABLE A

PARKING BRAKE  PARKING BRAKE CABLE  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE REAR WHEEL

Hide 4.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

Hide 6.REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY

a.

Disconnect the No. 1 parking brake cable from the parking brake lever (See page Brake>PARKING BRAKE>PARKING BRAKE LEVER>REMOVAL).


b.

Remove the 2 bolts and No. 1 heat insulator.


c.

Remove the No. 1 clip and pin from the No. 3 parking brake cable.

C237697
3.063,3.104 2.479,1.75 2.479,1.75 1.833,1.75 true 3.75,0.51 1.854,0.51 true 5.615,2.583 5.615,2.333 5.615,2.333 5.302,2.333 false 3.792,1.833 2.854,0.917 2.854,0.917 1.885,0.917 true 1.635,1.677 1.844,1.875 0.208,0.198 10 false *1 1.677,0.813 1.896,1 0.219,0.188 10 false *2 1.677,0.417 1.875,0.594 0.198,0.177 10 false *3 5.104,2.25 5.313,2.438 0.208,0.188 10 false *4
*1 No. 1 Parking Brake Cable *2 No. 3 Parking Brake Cable
*3 Parking Brake Equalizer *4 Cable Support Bracket



d.

Disconnect the No. 1 parking brake cable from the No. 3 parking brake cable.


e.

Disconnect the No. 1 parking brake cable from the parking brake equalizer.


f.

Remove the bolt holding the No. 1 parking brake cable.


g.

Remove the No. 1 parking brake cable clamp from the No. 1 parking brake cable.


h.

Disconnect the No. 1 parking brake cable from the cable support bracket.


i.

Disconnect the No. 1 parking brake cable from the cable support bracket.


Hide 7.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.

Disconnect the No. 2 parking brake cable from the parking brake shoe lever RH and backing plate RH.

i.

Disconnect the No. 2 parking brake cable from the parking brake shoe lever (See page Brake>BRAKE (REAR)>REAR BRAKE>DISASSEMBLY).

HINT:

Use the same procedure described for the LH side.



ii.

Remove the 2 bolts and disconnect the No. 2 parking brake cable from the backing plate.



b.

Remove the 2 bolts and No. 2 heat insulator.


c.

Disconnect the No. 2 parking brake cable from the parking brake equalizer.

C237698
4.583,2.323 4.583,3.01 4.583,3.01 3.969,3.01 true 1.052,2.5 1.052,3.375 true 3.771,2.906 3.979,3.094 0.208,0.188 10 false *1 0.99,3.375 1.198,3.594 0.208,0.219 10 false *2
*1 No. 2 Parking Brake Cable *2 Parking Brake Equalizer



d.

Remove the 4 bolts and No. 2 parking brake cable.


Hide 8.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Disconnect the No. 3 parking brake cable from the parking brake shoe lever LH and backing plate LH.

i.

Disconnect the No. 3 parking brake cable from the parking brake shoe lever (See page Brake>BRAKE (REAR)>REAR BRAKE>DISASSEMBLY).


ii.

Remove the 2 bolts and disconnect the No. 3 parking brake cable from the backing plate.



b.

Remove the No. 3 clip.

C237699
3.406,5.313 3.406,6.135 false 2.719,0.49 2.719,0.281 2.719,0.281 2.448,0.281 true 3.344,6.167 3.635,6.438 0.292,0.271 10 false *1 2.281,0.208 2.531,0.469 0.25,0.26 10 false *2
*1 No. 3 Parking Brake Cable *2 No. 3 Clip



c.

Remove the 4 bolts, nut and No. 3 parking brake cable.