Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1880E _58 Vehicle Interior _013242 SUPPLEMENTAL RESTRAINT SYSTEMS _0068641 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Passenger Side Pretensioner Squib Circuit  B1906/74  Open in Front Passenger Side Pretensioner Squib Circuit  B1907/74  Short to GND in Front Passenger Side Pretensioner Squib Circuit  B1908/74  Short to B+ in Front Passenger Side Pretensioner Squib Circuit  


DESCRIPTION

The front pretensioner squib circuit consists of the center airbag sensor and front seat outer belt.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the front pretensioner squib circuit during the primary check.

·

A front pretensioner squib malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly (Front pretensioner squib)

·

Center airbag sensor assembly


DTC is output in check mode.
B1906/74 Open in Front Passenger Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the front pretensioner squib circuit for 2 seconds.

·

A front pretensioner squib malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly (Front pretensioner squib)

·

Center airbag sensor assembly


DTC is output in check mode.
B1907/74 Short to GND in Front Passenger Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the front pretensioner squib circuit for 0.5 seconds.

·

A front pretensioner squib malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly (Front pretensioner squib)

·

Center airbag sensor assembly


DTC is output in check mode.
B1908/74 Short to B+ in Front Passenger Side Pretensioner Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the front pretensioner squib circuit for 0.5 seconds.

·

A front pretensioner squib malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly (Front pretensioner squib)

·

Center airbag sensor assembly


DTC is output in check mode.

WIRING DIAGRAM

C247622
3.396,2.594 2.458,2.594 false 0.74,3.198 3.146,3.365 2.406,0.167 10 false Front Pretensioner Squib 1.688,1.573 2.448,1.76 0.76,0.188 10 false R+*1, L+*2 1.729,2.417 2.49,2.604 0.76,0.188 10 false R-*1, L-*2 4.771,1.688 5.177,1.875 0.406,0.188 10 false PP+ 4.781,2.531 5.177,2.719 0.396,0.188 10 false PP- 2.458,1.563 2.604,1.729 0.146,0.167 10 false 1 2.479,2.406 2.635,2.563 0.156,0.156 10 false 2 4.583,1.594 4.698,1.76 0.115,0.167 10 false 4 4.583,2.427 4.708,2.594 0.125,0.167 10 false 5 4.76,4.177 5.083,4.365 0.323,0.188 10 false K39 4.75,4.323 6.198,4.531 1.448,0.208 10 false Center Airbag Sensor 0.74,3.031 1.792,3.188 1.052,0.156 10 false K40*1, K41*2 0.167,4.24 1.219,4.396 1.052,0.156 10 false *1: for LHD 0.167,4.51 1.219,4.667 1.052,0.156 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT (FRONT PRETENSIONER SQUIB)
C205411
0.333,2.25 0.75,2.5 0.417,0.25 0.333,2.74 0.75,2.99 0.417,0.25 2.073,2.5 2.458,2.719 false 0.438,2.292 0.958,2.594 0.521,0.302 10 false K40 1.021,1.073 1.271,1.375 0.25,0.302 10 false D 1.24,1.073 1.49,1.365 0.25,0.292 10 false C 1.552,1.708 2,2.031 0.448,0.323 10 false *a 2.354,2.188 2.677,2.427 0.323,0.24 10 false *3 2.063,1.417 2.479,1.792 0.417,0.375 10 false *2 0.771,0.458 1.083,0.76 0.313,0.302 10 false *1 2.51,2.646 3.042,2.979 0.531,0.333 10 false SST 0.438,2.792 0.958,3.094 0.521,0.302 10 false K41 0.833,2.302 1.281,2.625 0.448,0.323 10 false *A 0.844,2.781 1.292,3.104 0.448,0.323 10 false *B
*A for LHD
*B for RHD
*1 Front Pretensioner Squib
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Pretensioner Squib)


a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt (front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
C208251
0.604,0.76 0.99,1 0.385,0.24 10 false *1 1.25,0.75 1.531,0.979 0.281,0.229 10 false *2 1.719,1.656 2.042,1.906 0.323,0.25 10 false *3 1.896,1.021 2.229,1.302 0.333,0.281 10 false A 1.5,1.281 1.802,1.521 0.302,0.24 10 false B 1.104,1.281 1.417,1.552 0.313,0.271 10 false C 0.865,1.281 1.115,1.521 0.25,0.24 10 false D
*1 Front Pretensioner Squib
*2 Floor Wire
*3 Center Airbag Sensor


a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Check that the connectors (on the center airbag sensor side and front seat outer belt side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB CIRCUIT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB CIRCUIT)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


C205412
0.125,2.75 0.542,3 0.417,0.25 0.146,2.344 0.563,2.594 0.417,0.25 1.656,2.365 1.302,2.823 true 1.792,2.354 2.167,2.833 true 0.229,2.396 0.667,2.698 0.438,0.302 10 false K40 0.948,1.042 1.271,1.292 0.323,0.25 10 false D 1.958,0.813 2.25,1.104 0.292,0.292 10 false A 1.552,1.042 1.844,1.302 0.292,0.26 10 false B 1.177,1.042 1.438,1.271 0.26,0.229 10 false C 2.563,2.302 2.948,2.594 0.385,0.292 10 false *4 1.656,1.823 1.917,2 0.26,0.177 10 false *a 2.24,1.396 2.594,1.719 0.354,0.323 10 false *3 1.271,0.479 1.531,0.656 0.26,0.177 10 false *2 0.615,0.49 0.948,0.719 0.333,0.229 10 false *1 1.135,2.833 1.563,3.135 0.427,0.302 10 false R+*A 2.198,2.854 2.615,3.208 0.417,0.354 10 false R-*A 0.219,2.792 0.656,3.094 0.438,0.302 10 false K41 1.146,3.094 1.573,3.396 0.427,0.302 10 false L+*B 2.208,3.063 2.625,3.417 0.417,0.354 10 false L-*B 0.615,2.385 0.875,2.563 0.26,0.177 10 false *A 0.625,2.781 0.885,2.958 0.26,0.177 10 false *B
*A for LHD
*B for RHD
*1 Front Pretensioner Squib
*2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Front Pretensioner Squib)


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
K40-1 (R+) - Body ground Ignition switch ON Below 1 V
K40-2 (R-) - Body ground Ignition switch ON Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
K41-1 (L+) - Body ground Ignition switch ON Below 1 V
K41-2 (L-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K40-1 (R+) - K40-2 (R-) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
K41-1 (L+) - K41-2 (L-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K40-1 (R+) - K40-2 (R-) Always 1 MΩ or higher
K40-1 (R+) - Body ground Always 1 MΩ or higher
K40-2 (R-) - Body ground Always 1 MΩ or higher

for RHD
Tester Connection Condition Specified Condition
K41-1 (L+) - K41-2 (L-) Always 1 MΩ or higher
K41-1 (L+) - Body ground Always 1 MΩ or higher
K41-2 (L-) - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK AIR BAG SENSOR ASSEMBLY

NG

REPLACE FLOOR WIRE

4.CHECK AIR BAG SENSOR ASSEMBLY
C207519
1.552,1.615 2.073,1.979 0.521,0.365 10 false *2 0.854,0.802 1.281,1.073 0.427,0.271 10 false *1 1.021,1.271 1.375,1.531 0.354,0.26 10 false D 1.177,1.271 1.448,1.521 0.271,0.25 10 false C
*1 Front Pretensioner Squib LH
*2 Center Airbag Sensor Assembly


a.

Connect the connectors to the front seat outer belt and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG