Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068660 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turns the magnet clutch on based on the signal.

WIRING DIAGRAM

E234442E06
6.052,0.51 6.458,0.844 0.406,0.333 10 false AC1 6.042,1.281 6.458,1.625 0.417,0.344 10 false ACT 6.052,2.396 6.51,2.75 0.458,0.354 10 false MGC 2.083,3.573 3.385,4.031 1.302,0.458 10 false Magnet Clutch Relay 0.125,3.604 1.438,3.969 1.313,0.365 10 false from Ignition Switch 5.021,3.698 6.875,4.208 1.854,0.51 10 false Cooler Compressor Assembly 0.281,1.917 0.75,2.271 0.469,0.354 10 false ECM 0.583,0.5 1.042,0.865 0.458,0.365 10 false AC1 0.583,1.24 1.042,1.583 0.458,0.344 10 false ACT 5.417,2.854 5.833,3.188 0.417,0.333 10 false G94 5.729,2.26 6.094,2.625 0.365,0.365 10 false 13 5.01,3.51 5.479,3.792 0.469,0.281 10 false C33 2.073,3.375 2.479,3.667 0.406,0.292 10 false G71 0.281,1.74 0.698,2.042 0.417,0.302 10 false G88 5.802,1.115 6.073,1.406 0.271,0.292 10 false 7 2.979,2.25 3.24,2.542 0.26,0.292 10 false 1 4.771,3.333 5.021,3.635 0.25,0.302 10 false 1 2.198,2.271 2.49,2.573 0.292,0.302 10 false 2 2.99,2.896 3.25,3.208 0.26,0.313 10 false 3 2.219,2.885 2.5,3.208 0.281,0.323 10 false 5 5.75,0.385 6.052,0.698 0.302,0.313 10 false 21 1.01,0.396 1.354,0.74 0.344,0.344 10 false 24 1.021,1.135 1.354,1.417 0.333,0.281 10 false 25 5.417,3 7.042,3.604 1.625,0.604 10 false Air Conditioning Amplifier Assembly 0.521,2.542 1.667,2.906 1.146,0.365 10 false ECU-IG&GAUGE 5.042,4.01 6.896,4.521 1.854,0.51 10 false - Magnet Clutch Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (A/C SIGNAL)
a.

Use the Data List to check if the magnet clutch on request signal is functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/C Signal Magnet clutch on request signal ON or OFF ON: A/C switch on
OFF: A/C switch off
Check this item with the engine idling and the blower switch on (LO level).
Powertrain > Engine > Data List
Tester Display
A/C Signal
50003 61 191
OK:

Display is as specified in normal condition.



Result:
Proceed to
OK
NG



OK

2.INSPECT MAGNET CLUTCH RELAY

NG

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
2.INSPECT MAGNET CLUTCH RELAY

b.
E272046N02
1.99,0.708 1.698,0.5 true 1.833,1.802 2.302,1.521 true 2.906,0.542 2.604,0.729 true 2.833,1.51 2.438,1.156 true 0.438,1.229 0.719,1.542 0.281,0.313 10 false 1 1.563,0.406 1.844,0.719 0.281,0.313 10 false 1 1.427,1.25 1.708,1.563 0.281,0.313 10 false 2 2.948,0.427 3.271,0.74 0.323,0.313 10 false 2 1.729,1.771 2.01,2.042 0.281,0.271 10 false 3 1.427,0.802 1.708,1.115 0.281,0.313 10 false 5 0.438,0.781 0.719,1.094 0.281,0.313 10 false 3 2.885,1.49 3.198,1.833 0.313,0.344 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
a.

Disconnect the G94 air conditioning amplifier assembly connector.


b.
E272047C01
0.635,1.073 1.052,1.323 0.417,0.25 2.073,1.573 2.667,1.135 true 0.115,0.094 0.448,0.406 0.333,0.313 10 false *a 0.719,1.115 1.052,1.427 0.333,0.313 10 false G94 2.708,1.031 3.135,1.344 0.427,0.313 10 false MGC
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G94-13 (MGC) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.
E225456C11
0.823,0.156 1.24,0.406 0.417,0.25 1.385,1.74 0.865,1.01 true 0.146,0.125 0.49,0.458 0.344,0.333 10 false *a 0.906,0.198 1.25,0.531 0.344,0.333 10 false G94 1.333,1.75 1.677,2.083 0.344,0.333 10 false MGC
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G94-13 (MGC) - Body ground
·

Engine idling

·

A/C switch on (magnet clutch on permitted)


Below 1 V
·

Engine idling

·

A/C switch off or on (magnet clutch on not permitted)


11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT MAGNET CLUTCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
5.INSPECT MAGNET CLUTCH ASSEMBLY
a.

Remove the cooler compressor assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL


b.
E225413

Apply battery voltage to the magnet clutch and check operation of the magnet clutch.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Ground wire
Magnet clutch engages



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH RELAY - COOLER COMPRESSOR ASSEMBLY AND BATTERY)

NG

6.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH RELAY - COOLER COMPRESSOR ASSEMBLY AND BATTERY)
a.

Disconnect the C33 compressor connector.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G71-5 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G71-3 - C33-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
a.

Disconnect the G94 air conditioning amplifier assembly connector.


b.

Disconnect the G88 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G94-7 (ACT) - G88-25 (ACT) Always Below 1 Ω
G94-7 (ACT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.
E225456C40
0.646,0.115 1.115,0.365 0.469,0.25 1.51,1 1.51,1.688 true 0.75,0.156 1.188,0.406 0.438,0.25 10 false G94 1.427,1.771 1.792,1.958 0.365,0.188 10 false ACT 0.115,0.115 0.333,0.313 0.219,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G94-7 (ACT) - Body ground
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


Below 1 V



Result:
Proceed to
OK
NG



OK

NG

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
a.

Disconnect the G94 air conditioning amplifier assembly connector.


b.

Disconnect the G88 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G94-21 (AC1) - G88-24 (AC1) Always Below 1 Ω
G94-21 (AC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.
E225456C42
0.792,0.135 1.26,0.385 0.469,0.25 0.875,1.208 0.875,1.615 0.875,1.615 0.656,1.615 true 0.906,0.188 1.25,0.365 0.344,0.177 10 false G94 0.354,1.531 0.719,1.719 0.365,0.188 10 false AC1 0.146,0.115 0.365,0.313 0.219,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G94-21 (AC1) - Body ground
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V



Result:
Proceed to
OK
NG



OK

NG