C1401 Front Speed Sensor RH Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1402 Front Speed Sensor LH Malfunction
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for brake control.The speed sensor rotors have rows of alternating N and S magnetic poles and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU.
- HINT:
- When the connectors between the speed sensor and skid control ECU are connected, the following waveform is output.


| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1401 C1402 |
One of the following conditions is met:
|
|
| C1271 C1272 |
Stored only during test mode. |
|
- HINT:
- DTC C1401 is for the front speed sensor RH.
- DTC C1402 is for the front speed sensor LH.
- DTC C1401 is for the front speed sensor RH.
INSPECTION PROCEDURE
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
| 1. CHECK FRONT SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
Check the speed sensor installation (Click here).

Text in Illustration *1
Front Speed Sensor
*a
No clearance
*b
OK
*c
NG
- OK:
- There is no clearance between the sensor and the front steering knuckle.
- The installation bolt is tightened properly.
|
|
||||
| OK | |
| 2. INSPECT FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
|
|
||||
| OK | |
| 3. INSPECT FRONT SPEED SENSOR ROTOR |
Remove the front axle with ABS rotor bearing assembly (Click here).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- HINT:
- The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.
- If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED) |
Turn the ignition switch off
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
Front speed sensor RH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
FL Wheel Speed
Front speed sensor LH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | ||
| ||
| 5. REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
| NEXT | |
| 6. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
- HINT:
- The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.
- If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.
|
|
||||
| A | ||
| ||
