Brake Warning Light Remains ON
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The skid control ECU is connected to the combination meter via CAN communication.If any of the following is detected, the brake warning light remains on:
- The skid control ECU connector is disconnected from the skid control ECU.
- The brake fluid level is insufficient.
- The parking brake is applied.
- EBD operation is not possible.
- The voltage at terminal IG1 is high.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform calibration (Click here).
| 1. CHECK CAN COMMUNICATION SYSTEM |
Check if CAN communication system DTCs are output (for LHD without Entry and Start System: Click here, for RHD without Entry and Start System: Click here).
Result Result
Proceed to
DTC not output
A
DTC output
for LHD without Entry and Start System
B
DTC output
for RHD without Entry and Start System
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU connector is securely connected.
- OK:
- The connector is securely connected.
|
|
||||
| OK | |
| 3. CHECK TERMINAL VOLTAGE (IG1) |
Disconnect the A6 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A6-34 (IG1) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
Disconnect the A6 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A6-1 (GND1) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SW) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Parking Brake SW
Parking brake switch / ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.
- OK:
- When the parking brake is operated, the display changes as shown above.
|
|
||||
| OK | |
| 6. INSPECT BRAKE FLUID LEVEL WARNING SWITCH |
Turn the ignition switch off.
Remove the reservoir filler cap and strainer.
Disconnect the A44 brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.

- HINT:
- A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Switch off (Float up)
10 kΩ or higher
Switch on (Float down)
Below 1 Ω
Text in Illustration *a
Component without harness connected
(Brake Fluid Level Warning Switch)
- HINT:
- If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH) |
Disconnect the G6 combination meter connector.
Disconnect the A44 brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G6-31 (SW) - A44-1
Always
Below 1 Ω
G6-31 (SW) - Body ground
Always
10 kΩ or higher
A44-2 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 8. READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Brake Warning Light
Brake warning light / ON or OFF
OFF
-
When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List (Click here).
| Tester Display |
Test Part |
Control Range |
Diagnostic Note |
| Brake Warning Light |
Brake warning light |
Warning light ON/OFF |
Observe the combination meter. |
| Result |
Proceed to |
|
| Data List Display |
Data List Display when Performing Active Test ON/OFF Operation |
|
| ON |
Does not change between ON and OFF |
A |
| Changes between ON and OFF |
B |
|
| OFF |
Does not change between ON and OFF |
A |
| Changes between ON and OFF |
B |
|
|
|
||||
| A | ||
| ||
| 9. INSPECT PARKING BRAKE SWITCH |
Turn the ignition switch off.
Disconnect the G77 parking brake switch connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - Body ground
Parking brake switch on
(Switch pin not pushed in)
Below 1 Ω
Parking brake switch off
(Switch pin pushed in)
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Parking Brake Switch)
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU) |
Remove the main body ECU (Click here).
Disconnect the G77 parking brake switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-12 (PKB) - G77-1
Always
Below 1 Ω
A-12 (PKB) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
