P0365 Camshaft Position Sensor "B" Circuit (Bank 1)
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1)
- P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1)
- P0390 Camshaft Position Sensor "B" Circuit (Bank 2)
- P0392 Camshaft Position Sensor "B" Circuit Low Input (Bank 2)
- P0393 Camshaft Position Sensor "B" Circuit High Input (Bank 2)
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The exhaust camshaft's VVT sensor consists of a magnet and MRE (Magnetoresistive Element).The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference.
When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
The crank angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each crankshaft rotation. Based on a combination of the VVT signals and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0365 P0390 |
There is no exhaust VVT sensor signal for 5 seconds at an engine speed of 600 rpm or more (1 trip detection logic). |
|
| P0367 P0392 |
Output voltage of the VVT sensor for exhaust side (bank 1, 2) is less than 0.3 V for 4 seconds (1 trip detection logic). |
|
| P0368 P0393 |
Output voltage of the VVT sensor for exhaust side (bank 1, 2) is more than 4.7 V for 4 seconds (1 trip detection logic). |
|
-
Reference: Inspection using an oscilloscope

- HINT:
- The correct waveforms are as shown.
- EV1+ and EV2+ are the VVT sensor signal, and NE+ is the crankshaft position sensor signal.
- The wavelength becomes shorter as the engine speed increases.
Item
Content
Terminal
NE+ - NE-
EV1+ - EV1-
EV2+ - EV2-
Equipment Setting
5 V/DIV.
20 msec./DIV.
Condition
Idling with warm engine
- The correct waveforms are as shown.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- If no problem is found through by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK VVT SENSOR FOR EXHAUST SIDE (SENSOR POWER SOURCE) |
Disconnect the VVT sensor connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C22-3 (VC2) - Body ground
Ignition switch ON
4.5 to 5.5 V
C23-3 (VC2) - Body ground
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *A
Bank 1
*B
Bank 2
*a
Front view of wire harness connector
(to VVT Sensor)
Reconnect the VVT sensor connector.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM) |
Disconnect the VVT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C22-1 (EX+) - C34-13 (EV1+)
Always
Below 1 Ω
C22-2 (EX-) - C34-14 (EV1-)
Always
Below 1 Ω
C23-1 (EX+) - D34-18 (EV2+)
Always
Below 1 Ω
C23-2 (EX-) - C34-17 (EV2-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C22-1 (EX+) or C34-13 (EV1+) - Body ground
Always
10 kΩ or higher
C22-2 (EX-) or C34-14 (EV1-) - Body ground
Always
10 kΩ or higher
C23-1 (EX+) or D34-18 (EV2+) - Body ground
Always
10 kΩ or higher
C23-2 (EX-) or C34-17 (EV2-) - Body ground
Always
10 kΩ or higher
Reconnect the VVT sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST SIDE) |
Check the VVT sensor installation.

- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 4. CHECK EXHAUST CAMSHAFT (TIMING ROTOR) |
Check the timing rotor of the exhaust camshaft.
- OK:
- Camshaft timing rotor does not have any cracks or deformation.
|
|
||||
| OK | |
| 5. REPLACE VVT SENSOR FOR EXHAUST SIDE |
Replace the VVT sensor for exhaust side (Click here).
| NEXT | |
| 6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367, P0368, P0390, P0392 AND/OR P0393) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
No DTC is output
A
DTC P0365, P0367, P0368, P0390, P0392 and/or P0393 are output
B
- HINT:
- If the engine does not start, replace the ECM.
|
|
||||
| A | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM) |
Disconnect the VVT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C22-3 (VC2) - C34-15 (VCV1)
Always
Below 1 Ω
C23-3 (VC2) - C34-16 (VCV2)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C22-3 (VC2) or C34-15 (VCV1) - Body ground
Always
10 kΩ or higher
C23-3 (VC2) or C34-16 (VCV2) - Body ground
Always
10 kΩ or higher
Reconnect the VVT sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
