2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B2796 No Communication in Immobiliser System

Diagnostic trouble codes · Vehicles built from Aug 2013

Also covers:

DESCRIPTION

  1. DTC B2796 is stored when a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU assembly.
  2. DTC B2798 is stored when a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU assembly.
DTC Code
DTC Detection Condition
Trouble Area
B2796
The key code cannot be transmitted.
  1. Key
  2. Harness or connector
  3. Transponder key ECU assembly
  4. Transponder key amplifier
B2798
Key code identification cannot be completed within the specified time.
Key

WIRING DIAGRAM

B246376E07

INSPECTION PROCEDURE

NOTICE:
When replacing the transponder key ECU assembly, refer to the Service Bulletin.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2796 or B2798 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM)
  1. Use the Data List to check if the engine immobiliser system is functioning properly (Click here).

    Immobiliser 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser
    Immobiliser system status / Set or Unset
    Set: No key in ignition key cylinder
    Unset: Key inserted in ignition key cylinder
    -

    OK:
    Set (the key is not inserted in the ignition key cylinder) and Unset (the key is inserted in the ignition key cylinder) appear on the screen according to the key insertion condition.



NG
Go to step 4
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

4. CHECK WHETHER ENGINE STARTS WITH OTHER KEYS
  1. Check if the engine starts with an already registered vehicle key.

    OK:
    Engine starts.



NG
Go to step 5
OK

REREGISTER KEY CODE OR REPLACE KEY THAT CANNOT START ENGINE

5. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
  1. Disconnect the G138*1 or G74*2 ECU connector.

    1. *1: for 5L-E
    2. *2: except 5L-E

  1. Disconnect the G75 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 5L-E 
    Tester Connection
    Condition
    Specified Condition
    G138-14 (VC5) - G75-1 (VC5)
    Always
    Below 1 Ω
    G138-15 (CODE) - G75-4 (CODE)
    G138-4 (TXCT) - G75-5 (TXCT)
    G138-5 (AGND) - G75-7 (AGND)
    G138-14 (VC5) or G75-1 (VC5) - Body ground
    Always
    10 kΩ or higher
    G138-15 (CODE) or G75-4 (CODE) - Body ground
    G138-4 (TXCT) or G75-5 (TXCT) - Body ground
    G138-5 (AGND) or G75-7 (AGND) - Body ground
    except 5L-E 
    Tester Connection
    Condition
    Specified Condition
    G74-14 (VC5) - G75-1 (VC5)
    Always
    Below 1 Ω
    G74-15 (CODE) - G75-4 (CODE)
    G74-4 (TXCT) - G75-5 (TXCT)
    G74-5 (AGND) - G75-7 (AGND)
    G74-14 (VC5) or G75-1 (VC5) - Body ground
    Always
    10 kΩ or higher
    G74-15 (CODE) or G75-4 (CODE) - Body ground
    G74-4 (TXCT) or G75-5 (TXCT) - Body ground
    G74-5 (AGND) or G75-7 (AGND) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE TRANSPONDER KEY AMPLIFIER
  1. Temporarily replace the transponder key amplifier with a new or normally functioning one (Click here).


NEXT


7. CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts normally.

    OK:
    Engine starts normally.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (TRANSPONDER KEY AMPLIFIER IS DEFECTIVE)


← B2793 Transponder Chip Malfunction (+ B2794, B2795) (from Aug 2013)B2797 Communication Malfunction No. 1 (from Aug 2013) →