2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Fold Seat Switch Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the fold seat switch is operated, a switch operation signal is sent to the fold seat control ECU. The ECU receives switch operation signals from each switch and activates the reclining motor and cushion motor.

WIRING DIAGRAM

B239514E01

INSPECTION PROCEDURE


1. CHECK FOLD SEAT CONTROL ECU (FOLD SEAT SWITCH SIGNAL)

  1. Check the No. 1 fold seat switch signal.

    1. B243481E02
      Remove the fold seat control ECU with its connectors still connected (Click here).

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LH Side 
      Tester Connection
      Condition
      Specified Condition
      d1-10 (FLD2) - Body ground
      No. 1 fold seat switch LH off
      11 to 14 V
      No. 1 fold seat switch LH fold
      Below 1 V
      d1-14 (RTN2) - Body ground
      No. 1 fold seat switch LH off
      11 to 14 V
      No. 1 fold seat switch LH return
      Below 1 V
      for RH Side 
      Tester Connection
      Condition
      Specified Condition
      c1-10 (FLD2) - Body ground
      No. 1 fold seat switch RH off
      11 to 14 V
      No. 1 fold seat switch RH fold
      Below 1 V
      c1-14 (RTN2) - Body ground
      No. 1 fold seat switch RH off
      11 to 14 V
      No. 1 fold seat switch RH return
      Below 1 V

  1. Check No. 2 fold seat switch signal.

    1. B243481E03
      Remove the fold seat control ECU with its connectors still connected (Click here).

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LH Side 
      Tester Connection
      Condition
      Specified Condition
      d1-15 (RTRN) - Body ground
      No. 2 fold seat switch LH off
      11 to 14 V
      No. 2 fold seat switch LH return
      Below 1 V
      d1-16 (FOLD) - Body ground
      No. 2 fold seat switch LH off
      11 to 14 V
      No. 2 fold seat switch LH fold
      Below 1 V
      for RH Side 
      Tester Connection
      Condition
      Specified Condition
      c1-15 (RTRN) - Body ground
      No. 2 fold seat switch RH off
      11 to 14 V
      No. 2 fold seat switch RH return
      Below 1 V
      c1-16 (FOLD) - Body ground
      No. 2 fold seat switch RH off
      11 to 14 V
      No. 2 fold seat switch RH fold
      Below 1 V

      Text in Illustration 
      *A
      for LH Side
      *B
      for RH Side
      *a
      Component with harness connected
      (Fold Seat Control ECU)
      Result 
      Result
      Proceed to
      OK
      A
      NG (No. 1 fold seat switch signal)
      B
      NG (No. 2 fold seat switch signal)
      C



B
Go to step 2

C
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT NO. 1 FOLD SEAT SWITCH ASSEMBLY

  1. B239689E01
    Remove the No. 1 fold seat switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    6 (FLDL) - 7 (E)
    No. 1 fold seat switch LH fold
    Below 1 Ω
    No. 1 fold seat switch LH off
    10 kΩ or higher
    1 (RTNL) - 7 (E)
    No. 1 fold seat switch LH return
    Below 1 Ω
    No. 1 fold seat switch LH off
    10 kΩ or higher
    for RH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    8 (FLDR) - 7 (E)
    No. 1 fold seat switch RH fold
    Below 1 Ω
    No. 1 fold seat switch RH off
    10 kΩ or higher
    3 (RTNR) - 7 (E)
    No. 1 fold seat switch RH return
    Below 1 Ω
    No. 1 fold seat switch RH off
    10 kΩ or higher

    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



NG
REPLACE NO. 1 FOLD SEAT SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 1 FOLD SEAT SWITCH)
  1. *1: for LH Side
  2. *2: for RH Side
  1. Disconnect the d1*1 or c1*2 ECU connector.

  1. Disconnect the Q11*1 or R33*2 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    d1-10 (FLD2) - Q11-6 (FLDL)
    Always
    Below 1 Ω
    d1-10 (FLD2) - Body ground
    Always
    10 kΩ or higher
    d1-14 (RTN2) - Q11-1 (RTNL)
    Always
    Below 1 Ω
    d1-14 (RTN2) - Body ground
    Always
    10 kΩ or higher
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    c1-10 (FLD2) - R33-8 (FLDR)
    Always
    Below 1 Ω
    c1-10 (FLD2) - Body ground
    Always
    10 kΩ or higher
    c1-14 (RTN2) - R33-3 (RTNR)
    Always
    Below 1 Ω
    c1-14 (RTN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FOLD SEAT CONTROL ECU (Click here)

4. INSPECT NO. 2 FOLD SEAT SWITCH ASSEMBLY

  1. B239689E02
    Remove the No. 2 fold seat switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    8 (FOLD) - 7 (E)
    No. 2 fold seat switch LH fold
    Below 1 Ω
    No. 2 fold seat switch LH off
    10 kΩ or higher
    3 (RTRN) - 7 (E)
    No. 2 fold seat switch LH return
    Below 1 Ω
    No. 2 fold seat switch LH off
    10 kΩ or higher
    for RH Side 
    Tester Connection
    Switch Condition
    Specified Condition
    6 (FOLD) - 7 (E)
    No. 2 fold seat switch RH fold
    Below 1 Ω
    No. 2 fold seat switch RH off
    10 kΩ or higher
    1 (RTRN) - 7 (E)
    No. 2 fold seat switch RH return
    Below 1 Ω
    No. 2 fold seat switch RH off
    10 kΩ or higher

    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



NG
REPLACE NO. 2 FOLD SEAT SWITCH ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 2 FOLD SEAT SWITCH)
  1. Disconnect the d1*1 or c1*2 ECU connector.

    1. *1: for LH Side
    2. *2: for RH Side

  1. Disconnect the R12 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    d1-15 (RTRN) - R12-3 (RTRN)
    Always
    Below 1 Ω
    d1-15 (RTRN) - Body ground
    Always
    10 kΩ or higher
    d1-16 (FOLD) - R12-8 (FOLD)
    Always
    Below 1 Ω
    d1-16 (FOLD) - Body ground
    Always
    10 kΩ or higher
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    c1-15 (RTRN) - R12-1 (RTRN)
    Always
    Below 1 Ω
    c1-15 (RTRN) - Body ground
    Always
    10 kΩ or higher
    c1-16 (FOLD) - R12-6 (FOLD)
    Always
    Below 1 Ω
    c1-16 (FOLD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FOLD SEAT CONTROL ECU (Click here)


← Fold Seat Switch Circuit (Aug 2013 – Jul 2014)Folding Motor Circuit (Aug 2013 – Jul 2014) →