Glass Breakage Sensor Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the glass breakage sensor detects that the back door glass, quarter window assembly LH* or quarter window assembly RH* is broken, the sensor sounds the alarm for 30 seconds.- *: for 5 Door
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (GLASS BREAKAGE SENSOR) |
Using the intelligent tester, read the Data List (Click here).
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Sealed Glas Brak Sen
Glass breakage sensor detection / With or Without
With: Glass breakage sensor operating
Without: Glass breakage sensor not operating
-
- OK:
- "With" (glass breakage sensor operating) appears on screen.
Result Result
Proceed to
OK
A
NG (for 5 Door)
B
NG (for 3 Door)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. INSPECT QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR) |
Disconnect the R25 sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 (SSR+) - 2 (SSR-)
Always
Below 1 Ω
|
|
||||
| OK | |
| 3. INSPECT QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR) |
Disconnect the Q20 sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 (SSR+) - 2 (SSR-)
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. INSPECT BACK DOOR GLASS (GLASS BREAKAGE SENSOR) |
Disconnect the Y2 sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 (SSR+) - 1 (E)
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR - MAIN BODY ECU AND BODY GROUND) |
Disconnect the R25, Q20 and Y2 sensor connectors.
Remove the main body ECU (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R25-1 (SSR+) - A-19 (GPBS)
Always
Below 1 Ω
Q20-1 (SSR+) - R25-2 (SSR-)
Always
Below 1 Ω
Y2-3 (SSR+) - Q20-2 (SSR-)
Always
Below 1 Ω
R25-1 (SSR+) or A-19 (GPBS) - Body ground
Always
10 kΩ or higher
Q20-1 (SSR+) or R25-2 (SSR-) - Body ground
Always
10 kΩ or higher
Y2-3 (SSR+) or Q20-2 (SSR-) - Body ground
Always
10 kΩ or higher
Y2-1 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 6. INSPECT BACK DOOR GLASS (GLASS BREAKAGE SENSOR) |
w/ Glass Hatch Opener System:

Disconnect the Y2 sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 (SSR+) - 1 (E)
Always
Below 1 Ω
w/o Glass Hatch Opener System:

Disconnect the X8 sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2 (SSR+) - 1 (E)
Always
Below 1 Ω
Result Result
Proceed to
OK
A
NG (w/ Glass Hatch Opener System)
B
NG (w/o Glass Hatch Opener System)
C
|
|
||||
|
|
||||
| A | |
| 7. CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR - MAIN BODY ECU AND BODY GROUND) |
w/ Glass Hatch Opener System:
Disconnect the Y2 sensor connector.
Remove the main body ECU (Click here).
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Y2-3 (SSR+) - A-19 (GPBS)
Always
Below 1 Ω
Y2-3 (SSR+) or A-19 (GPBS) - Body ground
Always
10 kΩ or higher
Y2-1 (E) - Body ground
Always
Below 1 Ω
w/o Glass Hatch Opener System:
Disconnect the X8 sensor connector.
Remove the main body ECU (Click here).
- Standard Resistance:
Tester Connection
Condition
Specified Condition
X8-2 (SSR+) - A-19 (GPBS)
Always
Below 1 Ω
X8-2 (SSR+) or A-19 (GPBS) - Body ground
Always
10 kΩ or higher
X8-1 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
