2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Glass Breakage Sensor Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the glass breakage sensor detects that the back door glass, quarter window assembly LH* or quarter window assembly RH* is broken, the sensor sounds the alarm for 30 seconds.
  1. *: for 5 Door

WIRING DIAGRAM

B240859E01
B240860E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (GLASS BREAKAGE SENSOR)
  1. Using the intelligent tester, read the Data List (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Sealed Glas Brak Sen
    Glass breakage sensor detection / With or Without
    With: Glass breakage sensor operating
    Without: Glass breakage sensor not operating
    -

    OK:
    "With" (glass breakage sensor operating) appears on screen.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 5 Door)
    B
    NG (for 3 Door)
    C



B
Go to step 2

C
Go to step 6
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR)

  1. B240861E01
    Disconnect the R25 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SSR+) - 2 (SSR-)
    Always
    Below 1 Ω



NG
REPLACE QUARTER WINDOW ASSEMBLY LH (GLASS BREAKAGE SENSOR) (Click here)
OK


3. INSPECT QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR)

  1. B240861E01
    Disconnect the Q20 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SSR+) - 2 (SSR-)
    Always
    Below 1 Ω



NG
REPLACE QUARTER WINDOW ASSEMBLY RH (GLASS BREAKAGE SENSOR) (Click here)
OK


4. INSPECT BACK DOOR GLASS (GLASS BREAKAGE SENSOR)

  1. B240863E01
    Disconnect the Y2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (SSR+) - 1 (E)
    Always
    Below 1 Ω



NG
REPLACE BACK DOOR GLASS (GLASS BREAKAGE SENSOR) (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the R25, Q20 and Y2 sensor connectors.

  1. Remove the main body ECU (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R25-1 (SSR+) - A-19 (GPBS)
    Always
    Below 1 Ω
    Q20-1 (SSR+) - R25-2 (SSR-)
    Always
    Below 1 Ω
    Y2-3 (SSR+) - Q20-2 (SSR-)
    Always
    Below 1 Ω
    R25-1 (SSR+) or A-19 (GPBS) - Body ground
    Always
    10 kΩ or higher
    Q20-1 (SSR+) or R25-2 (SSR-) - Body ground
    Always
    10 kΩ or higher
    Y2-3 (SSR+) or Q20-2 (SSR-) - Body ground
    Always
    10 kΩ or higher
    Y2-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

6. INSPECT BACK DOOR GLASS (GLASS BREAKAGE SENSOR)

  1. B240863E01
    w/ Glass Hatch Opener System:
    1. Disconnect the Y2 sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (SSR+) - 1 (E)
      Always
      Below 1 Ω

  1. B240862E01
    w/o Glass Hatch Opener System:
    1. Disconnect the X8 sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (SSR+) - 1 (E)
      Always
      Below 1 Ω

      Result 
      Result
      Proceed to
      OK
      A
      NG (w/ Glass Hatch Opener System)
      B
      NG (w/o Glass Hatch Opener System)
      C



B
REPLACE BACK DOOR GLASS (GLASS BREAKAGE SENSOR) (Click here)

C
REPLACE BACK DOOR GLASS (GLASS BREAKAGE SENSOR) (Click here)
A


7. CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR - MAIN BODY ECU AND BODY GROUND)
  1. w/ Glass Hatch Opener System:

    1. Disconnect the Y2 sensor connector.

    2. Remove the main body ECU (Click here).

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Y2-3 (SSR+) - A-19 (GPBS)
      Always
      Below 1 Ω
      Y2-3 (SSR+) or A-19 (GPBS) - Body ground
      Always
      10 kΩ or higher
      Y2-1 (E) - Body ground
      Always
      Below 1 Ω

  1. w/o Glass Hatch Opener System:

    1. Disconnect the X8 sensor connector.

    2. Remove the main body ECU (Click here).

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      X8-2 (SSR+) - A-19 (GPBS)
      Always
      Below 1 Ω
      X8-2 (SSR+) or A-19 (GPBS) - Body ground
      Always
      10 kΩ or higher
      X8-1 (E) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← Security Indicator Light Circuit (from Aug 2014)Glass Breakage Sensor Circuit (from Aug 2014) →