2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. REMOVE SPARE WHEEL COVER PAD (w/ Back Door Tire Carrier)

  1. B239475
    Detach the 7 claws and move the wheel cover pad out of the way.


2. REMOVE SPARE WHEEL COVER (w/ Back Door Tire Carrier)

  1. B241517
    Remove the bolt.

  1. Move the lever.

  1. B239474
    Detach the 8 claws and remove the spare wheel cover.


3. REMOVE SPARE TIRE (w/ Back Door Tire Carrier)

4. REMOVE NO. 2 SPARE WHEEL COVER (w/ Back Door Tire Carrier)

  1. B239476
    Remove the 4 screws and No. 2 spare wheel cover.


5. REMOVE TELEVISION CAMERA BRACKET (w/ Back Door Tire Carrier)

E197653
  1. Disconnect the connector and detach the clamp.

  1. Remove the 2 bolts and television camera bracket with rear television camera.


6. REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/ Back Door Tire Carrier)

E197654
  1. Disconnect the connector and remove the rear No. 2 window wire.

  1. Remove the bolt and rear television camera.


7. REMOVE SPARE WHEEL CARRIER BRACKET SUB-ASSEMBLY (w/ Back Door Tire Carrier)

  1. B239478
    Remove the 2 bolts, 2 nuts and spare wheel carrier bracket sub-assembly.

  1. B239479
    Using E10 "TORX" sockets, remove the 2 stud bolts.

    NOTICE:
    If a stud bolt is deformed or its threads are damaged, replace it.


8. REMOVE BACK DOOR CENTER GARNISH

  1. B239438
    Detach the 4 clips and remove the back door center garnish.


9. REMOVE BACK DOOR SIDE GARNISH LH

  1. B239439
    Detach the 2 clips and claw and remove the back door side garnish.


10. REMOVE BACK DOOR SIDE GARNISH RH

  1. B239440
    Detach the 2 clips and claw and remove the back door side garnish.


11. REMOVE BACK DOOR TRIM COVER

  1. B239441
    Remove the back door trim cover as shown in the illustration.


12. REMOVE UPPER TOOL BOX PANEL SUB-ASSEMBLY

  1. B239442
    Remove the upper tool box panel sub-assembly as shown in the illustration.


13. REMOVE TOOL CASE

  1. B239445
    Detach the 2 claws and remove the tool case.


14. REMOVE BACK DOOR LOCK COVER (w/o Back Door Tire Carrier)

  1. B239443
    Using moulding remover B, detach the clip and 6 claws and remove the back door lock cover.


15. REMOVE BACK DOOR INSIDE HANDLE BEZEL (for Face to Face Seat Type)

  1. B239466
    Remove the screw.

  1. Detach the 5 claws and remove the back door inside handle bezel.


16. REMOVE BACK DOOR TRIM PANEL ASSEMBLY

  1. B241516
    Detach the claw and remove the cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B239444
    Remove the screw.

  1. w/o Back Door Tire Carrier:

    1. B239446
      Remove the bolt.

    2. Detach the 15 clips and remove the back door trim panel assembly.

  1. w/ Back Door Tire Carrier:

    1. B239447
      Remove the bolt.

    2. Detach the 16 clips and remove the back door trim panel assembly.

  1. for Face to Face Seat Type:

    1. B241528
      Remove the screw and bolt.

    2. Detach the 15 clips and remove the back door trim panel assembly.


17. REMOVE BACK DOOR INSIDE HANDLE SUB-ASSEMBLY (for Face to Face Seat Type)

  1. B239467
    Detach the guide.

  1. Detach the claws and remove the inside handle sub-assembly.

  1. Disconnect the 2 cables from the inside handle sub-assembly.


18. REMOVE TOOL BOX BRACKET

  1. B239448
    Remove the 4 bolts and 2 tool box brackets.


19. REMOVE BACK DOOR SERVICE HOLE COVER

  1. B239449
    Remove the service hole cover.


20. REMOVE BACK DOOR OUTSIDE HANDLE LH

  1. w/ Back Door Tire Carrier:

    1. B239453E01
      Remove the hole plug.
      Text in Illustration 
      *1
      Hole Plug

    2. Remove the 2 nuts and back door outside handle.

    3. Disconnect the cable.

  1. w/o Back Door Tire Carrier:

    1. B239451
      Remove the 2 nuts and back door outside handle.

    2. Disconnect the cable.


21. REMOVE BACK DOOR LOCK ASSEMBLY
  1. Disconnect the connector.

  1. B243055E01
    Using a T30 "TORX" wrench, remove the 3 screws.
    Text in Illustration 
    *A
    for Standard Type
    *B
    w/ Back Door Tire Carrier, for Face to Face Seat Type

    NOTICE:
    Be careful when removing the bolts as the door lock may fall and become damaged.

  1. B239458
    Disconnect the cable and remover the back door lock assembly.

  1. Remove the door lock wiring harness seal from the back door lock assembly.


22. REMOVE BACK DOOR LOCK CONTROL CABLE ASSEMBLY

  1. B239458
    Disconnect the cable.


23. REMOVE REAR NO. 1 WINDOW WIRE (w/ Back Door Tire Carrier)

  1. B239477E01
    Disconnect the connector.
    Text in Illustration 
    *a
    Outer Side
    *b
    Inner Side

  1. Detach the 2 clamps and remove the rear No. 1 window wire.


24. REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/o Back Door Tire Carrier)

E197658
  1. Disconnect the connector.

  1. Remove the 2 bolts and rear television camera.


25. REMOVE NO. 2 BACK DOOR GARNISH RETAINER (w/o Rear View Monitor System)

  1. w/o Back Door Tire Carrier:

    1. B239503
      Remove the 2 screws and No. 2 back door garnish retainer.


26. REMOVE LOWER BACK DOOR OUTSIDE GARNISH MOULDING LH (w/o Back Door Tire Carrier)

B238978E01
  1. Using a screwdriver, detach the 5 claws and remove the outside garnish moulding.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


27. REMOVE LOWER BACK DOOR OUTSIDE GARNISH MOULDING RH (w/o Back Door Tire Carrier)

  1. B243803
    Detach the 5 claws and remove the moulding.


28. REMOVE LOWER BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE LH (w/o Back Door Tire Carrier)

B238979
  1. Disconnect the connector and detach the clamp.

  1. Remove the screw.

  1. Detach the double-sided tape.

  1. Using a screwdriver, detach the 5 claws and remove the outside garnish.

    NOTICE:
    Be careful not to damage the vehicle body.


    B238980E01
    Text in Illustration 
    *1
    Protective Tape
    *2
    Double-sided Tape


29. REMOVE LOWER BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE RH (w/o Back Door Tire Carrier)

  1. Remove the screw.

    B243802E01

    Text in Illustration 
    *1
    Double-Sided Tape
    -
    -

  1. Detach the 4 claws and remove the lower door garnish sub-assembly outside.


30. REMOVE GLASS HATCH OPENER SWITCH ASSEMBLY (w/o Back Door Tire Carrier)

B238981
  1. Remove the screw and opener switch.


31. REMOVE SWITCH COVER (w/o Back Door Tire Carrier)

B238982
  1. Remove the switch cover.


32. REMOVE NO. 2 BACK DOOR WEATHERSTRIP (w/o Back Door Tire Carrier)

  1. B239456
    Remove the No. 2 back door weatherstrip.


33. REMOVE BACK DOOR SIDE FEMALE STOPPER SUB-ASSEMBLY LH

  1. B239455
    Remove the 2 bolts and back door side female stopper sub-assembly.


34. REMOVE BACK DOOR NO. 2 STOPPER CUSHION

  1. B239470
    Remove the back door No. 2 stopper cushion.


35. REMOVE BACK DOOR NO. 1 STOPPER

  1. B239471
    Using a clip remover, detach the 2 claws and remove the back door No. 1 stopper.


36. REMOVE BACK DOOR PANEL CUSHION (w/o Back Door Tire Carrier)

  1. B239472
    Remove the 4 back door panel cushions.


37. REMOVE BACK WINDOW LOCK ASSEMBLY (w/o Back Door Tire Carrier)

B238983
  1. Disconnect the connector.

  1. Remove the 3 bolts and back window lock assembly.


38. REMOVE REAR NO. 1 SPOILER COVER (w/o Back Door Tire Carrier)

B247537E01
  1. Detach the fastening tape and 5 clips and remove the rear No. 1 spoiler cover.

    Text in Illustration 
    *1
    Fastening Tape


39. REMOVE REAR SPOILER COVER RH

B247537E01
  1. Detach the fastening tape and 5 clips and remove the rear No. 1 spoiler cover.

    Text in Illustration 
    *1
    Fastening Tape


40. REMOVE REAR SPOILER SUB-ASSEMBLY
  1. w/o Back Door Tire Carrier:
    Remove the rear spoiler sub-assembly (Click here).

  1. w/ Back Door Tire Carrier:
    Remove the rear spoiler sub-assembly (Click here).


41. REMOVE NO. 2 BACK DOOR STIFFENER (w/ Back Door Tire Carrier)

B237905E01

HINT:
Use the same procedure to remove the No. 2 back door stiffener on the other side.

  1. Put protective tape around the No. 2 back door stiffener.

  1. Using a clip remover, detach the 2 claws and remove the No. 2 back door stiffener.

    HINT:
    Tape the clip remover tip before use.

    Text in Illustration 
    *1
    Protective Tape


42. REMOVE REAR WASHER NOZZLE SUB-ASSEMBLY

  1. E202055
    Disconnect the hose.

  1. E201562
    Detach the 2 claws and remove the washer nozzle.


43. REMOVE REAR WIPER ARM

  1. E197697
    Remove the nut and rear wiper arm.


44. REMOVE REAR WIPER MOTOR ASSEMBLY

  1. E197698E01
    Disconnect the washer hose and wiper motor connector.
    Text in Illustration 
    *A
    w/ Back Door Tire Carrier
    *B
    w/o Back Door Tire Carrier

  1. E197701E01
    Remove the 3 bolts.
    Text in Illustration 
    *A
    w/ Back Door Tire Carrier
    *B
    w/o Back Door Tire Carrier

  1. Detach the 2 guides and remove the rear wiper motor.


45. REMOVE NO. 1 BACK WINDOW WIPER MOTOR BRACKET (w/ Back Door Tire Carrier)

  1. B239460
    Using a clip remover, detach the clamp.

  1. Remove the 3 bolts.

  1. Using a clip remover, detach the 2 clips and remove the No. 1 back window wiper motor bracket.


46. REMOVE BACK DOOR LOCK STRIKER COVER (w/o Back Door Tire Carrier)

47. REMOVE BACK WINDOW STAY ASSEMBLY LH (w/o Back Door Tire Carrier)

  1. B238986E01
    Using a screwdriver, remove the 2 stop rings as shown in the illustration, and then remove the back window stay.

    CAUTION:
    Remove the back window stay while supporting the back door with one hand.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


48. REMOVE BACK WINDOW STAY ASSEMBLY RH (w/o Back Door Tire Carrier)

HINT:
Use the same procedure described for the LH side.


49. REMOVE BACK DOOR STAY BOLT (w/o Back Door Tire Carrier)

  1. B243801E01
    Remove the 2 back door stay bolts.
    Text in Illustration 
    *A
    for RH Side
    *B
    for LH Side


50. REMOVE BACK DOOR GLASS (w/o Back Door Tire Carrier)

  1. B242843
    Remove the connector and detach the 2 clamps.

  1. B239004
    Remove the 4 bolts and back window glass.


51. REMOVE BACK DOOR CUSHION (w/ Back Door Tire Carrier)

  1. B239473
    Remove the 3 back door cushions.


52. REMOVE REAR BUMPER BAR PLATE
  1. Put protective tape around the rear bumper bar plate.

  1. Detach the 14 claws and remove the rear bumper bar plate.

    B236403E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -


53. REMOVE BACK DOOR CHECK

NOTICE:
  1. If the back door check is detached from a ball joint, do not reuse it as the connection with the ball joint will be loose, resulting in the back door check falling off.
  2. If the back door check is detached from a ball joint, it becomes non-reusable. Therefore, do not detach the back door check from a ball joint unless replacing it.

  1. B340680
    Remove the 2 bolts.

  1. Using a clip remover, detach the clip and remove the back door check with back door lower damper stay bracket.

  1. B246611
    Detach the wire harness clamp.

  1. Remove the 3 bolts and back door check with back door lower damper stay bracket.


54. REMOVE BACK DOOR LOWER DAMPER STAY BRACKET LH

NOTICE:
  1. If the back door check is detached from a ball joint, do not reuse it as the connection with the ball joint will be loose, resulting in the back door check falling off.
  2. If the back door check is detached from a ball joint, it becomes non-reusable. Therefore, do not detach the back door check from a ball joint unless replacing it.
  3. The back door lower damper stay bracket on the back door side cannot be removed from the back door check. Therefore, if the back door check or back door damper stay bracket is replaced, prepare a new back door check and back door damper stay bracket.

  1. Bumper side:

    1. B239464E01
      Using a screwdriver, remove the stop ring as shown in the illustration, and then remove the back door check.

      NOTICE:
      Tape the screwdriver tip before use.

      Text in Illustration 
      *1
      Protective Tape


55. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
  1. w/o Back Door Tire Carrier:
    Remove the back door outside garnish (Click here).

  1. w/ Back Door Tire Carrier:
    Remove the back door outside garnish (Click here).


56. REMOVE LICENSE PLATE LIGHT CORD (w/o Entry and Start System)
  1. w/o Back Door Tire Carrier:
    Remove the license plate light cord (Click here).

  1. w/ Back Door Tire Carrier:
    Remove the license plate light cord (Click here).


57. REMOVE NO. 1 BACK DOOR GARNISH RETAINER (w/o Back Door Tire Carrier)

B357967
  1. Remove the 3 screws and No. 1 back door garnish retainer.


58. REMOVE REAR LICENSE LIGHT COVER (w/ Back Door Tire Carrier)

B237899
  1. Remove the 5 screws and rear license light cover.


59. REMOVE BACK DOOR ELECTRICAL KEY SWITCH (w/o Back Door Tire Carrier)

  1. B358818
    Detach the clamp.

  1. B358819
    Remove the 2 screws.

  1. Detach the 2 guides and remove the back door electrical key switch.


60. REMOVE BACK DOOR ELECTRICAL KEY SWITCH (w/ Back Door Tire Carrier)

  1. B241159
    Remove the 2 screws.

  1. Detach the 2 guides and remove the back door electrical key switch.


61. REMOVE LICENSE PLATE LIGHT ASSEMBLY
  1. w/o Back Door Tire Carrier:
    Remove the license plate light (Click here).

  1. w/ Back Door Tire Carrier:
    Remove the license plate light (Click here).

← COMPONENTS (from Aug 2013)ADJUSTMENT (from Aug 2013) →