2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1442/42 Air Inlet Damper Control Servo Motor Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The recirculation damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet damper to any position, which controls the intake air settings (fresh, fresh/recirculation and recirculation).

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.

DTC Code
DTC Detection Condition
Trouble Area
B1442/42
The air inlet damper position does not change when the air conditioning amplifier assembly operates the recirculation damper servo sub-assembly.
  1. Recirculation damper servo sub-assembly
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM

E180810E51

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1442/42 is not output
    A
    DTC B1442/42 is output
    B
    DTC B1442/42 and B1497/97 are output
    C



B
Go to step 2

C
GO TO B1497/97 (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

2. READ VALUE USING INTELLIGENT TESTER (RECIRCULATION DAMPER SERVO)
  1. Use the Data List to check if the recirculation damper servo sub-assembly is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Inlet Damper Targ Pulse
    Recirculation damper servo sub-assembly target pulse / Min.: 0, Max.: 255
    7 (pulse): Recirculation
    28 (pulse): Fresh
    -
    Air Inlet Damper Actual Pulse
    Recirculation damper servo sub-assembly actual pulse / Min.: 0, Max.: 255
    7 (pulse): Recirculation
    28 (pulse): Fresh
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to the DTC)
    A
    OK (When troubleshooting according to Problem Symptoms Table
    B
    Both target pulse and actual pulse do not display
    C
    Target pulse displays normally, but actual pulse does not display
    D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
Go to step 4
A


3. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1442 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

4. CHECK RECIRCULATION DAMPER SERVO SUB-ASSEMBLY
  1. Replace the recirculation damper servo sub-assembly (Click here).

    HINT:
    Since the recirculation damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the recirculation damper servo sub-assembly with a new or normally functioning one.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1442 is not output.



NG
Go to step 5
OK

END (RECIRCULATION DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

5. CHECK AIR CONDITIONING HARNESS ASSEMBLY
  1. Temporarily replace the air conditioning harness assembly with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1442 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)


← B1442/42 Air Inlet Damper Control Servo Motor Circuit (Aug 2013 – Jul 2014)B1443/43 Air Outlet Damper Control Servo Motor Circuit (Aug 2013 – Jul 2014) →