2013-2015 Land Cruiser Prado · Service Manual Suspension

C1784/84 Steering Sensor Signal Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The steering angle sensor signal is sent to the suspension control ECU through CAN communication system. When there is a communication malfunction, this DTC is detected by the diagnosis function.
DTC Code
DTC Detection Condition
Trouble Area
C1784/84
A steering angle sensor signal malfunction is detected, or a steering angle sensor power source malfunction signal is detected for 5 seconds or more.
  1. Steering angle sensor (spiral cable sub-assembly)
  2. Steering angle sensor power source circuit
  3. Suspension control ECU

WIRING DIAGRAM

C214176E03

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the suspension control ECU, perform registration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. Do not remove the steering angle sensor from the spiral cable sub-assembly.
  4. When replacing the spiral cable sub-assembly, confirm that the replacement part is of the correct specification.

HINT:
If DTC C1782/82 is output at the same time as C1784/84, perform troubleshooting for C1782/82 first (Click here).


1. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Perform a road test.

  1. Check if DTCs C1784/84 and U0126/71 are output (Click here).

    Result 
    Condition
    Proceed to
    DTC is not output or only DTC 1784/84 is output
    A
    DTCs 1784/84 and U0126/71 are output
    B



B
GO TO DTC U0126/71 (Click here)
A


2. CHECK DTC (VEHICLE STABILITY CONTROL SYSTEM)
  1. Check for steering angle sensor malfunction DTCs (Click here).

    Result 
    Condition
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO VEHICLE STABILITY CONTROL SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)
A


3. CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, BAT, ESS)
  1. Disconnect the G33 steering angle sensor connector.

  1. C207362E07
    Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G33-5 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    G33-6 (BAT) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G33-2 (ESS) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)

  1. Check that the steering angle sensor connector is not deformed or corroded.

    OK:
    No deformation or corrosion.

    HINT:
    If the steering angle sensor connector is defective, replace the spiral cable sub-assembly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. READ VALUE USING INTELLIGENT TESTER (STEERING ANGLE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Data List.

    Air Suspension 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Steering Angle
    Steering angle/
    Min.: -49152.0 deg
    Max.: 49150.5 deg
    Actual steering angle
    Turned left: reading increases
    Turned right: reading decreases
    -

    OK:
    Steering wheel turning angle value changes when steering wheel is turned.



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1783/83 Front Wheels Speed Sensor Signal Malfunction (from Aug 2014)C1784/84 Steering Sensor Signal Malfunction (from Aug 2014) →