2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Wireless Transmitter Memory Function does not Operate

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

With the ignition switch ON, press the manual door control switch LOCK or UNLOCK while holding a seat memory switch (M1 switch or M2 switch). Doing so registers the transmitter recognition code into the seat memory switch that was pressed. After registration is completed, the answer-back buzzer sounds.

INSPECTION PROCEDURE

NOTICE:
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.


1. CHECK POWER DOOR LOCK CONTROL FUNCTION
  1. Using the standard operation procedure, check that the power door lock/unlock function operates normally (Click here).

    OK:
    Power door lock/unlock function operates normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Using the standard operation procedure, check that the wireless door lock/unlock function operates normally (Click here).

    OK:
    Wireless door lock/unlock function operates normally.



NG
GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (Click here)
OK


3. CHECK VEHICLE TYPE
  1. Check vehicle type.

    Result 
    Result
    Proceed to
    w/ Entry and Start System
    A
    w/o Entry and Start System
    B



B
Go to step 5
A


4. CHECK ENTRY AND START SYSTEM (ENTRY UNLOCK FUNCTION)
  1. Check the entry unlock function of the entry and start system (Click here).

    OK:
    Entry unlock function operates normally.



NG
GO TO ENTRY AND START SYSTEM (Click here)
OK


5. CHECK SEAT MEMORY FUNCTION
  1. Perform a seat memory operation properly (Click here).

  1. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory operation.

    NOTICE:
    1. The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
    2. If a memorizing operation fails, release all switches. The seat memory function does not operate unless the switches are released.

    OK:
    Seat position memory function operates normally.



NG
GO TO PROBLEM SYMPTOMS TABLE (Power Seat Position is not Memorized) (Click here)
OK


6. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY)
  1. Using the intelligent tester, read the Data List (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Courtesy
    Front door courtesy light switch assembly signal / ON or OFF
    ON: Driver side door open
    OFF: Driver side door closed
    -

    OK:
    On intelligent tester screen, each item changes between ON and OFF according to above chart.



NG
GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit) (Click here)
OK


7. CHECK MEMORY CALL FUNCTION (MEMORY ERASURE)
  1. Perform the memory erasure operation (Click here).


NEXT


8. READ VALUE USING INTELLIGENT TESTER (MEMORY REGISTRATION)
  1. Perform the memory registration operation while checking the tester screen (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mem SW No. w/KeyID1
    Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2 or MEM SW3
    NONE: No switches linked with key ID1
    MEM SW1: M1 switch linked with key ID1
    MEM SW2: M2 switch linked with key ID1
    MEM SW3: Related switch does not exist
    -
    Mem SW No. w/KeyID2
    Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2 or MEM SW3
    NONE: No switches linked with key ID2
    MEM SW1: M1 switch linked with key ID2
    MEM SW2: M2 switch linked with key ID2
    MEM SW3: Related switch does not exist
    -
    Mem SW No. w/KeyID3
    Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2 or MEM SW3
    NONE: No switches linked with key ID3
    MEM SW1: M1 switch linked with key ID3
    MEM SW2: M2 switch linked with key ID3
    MEM SW3: Related switch does not exist
    -
    Mem SW No. w/KeyID4
    Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2 or MEM SW3
    NONE: No switches linked with key ID4
    MEM SW1: M1 switch linked with key ID4
    MEM SW2: M2 switch linked with key ID4
    MEM SW3: Related switch does not exist
    -
    Mem SW No. w/KeyID5
    Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2 or MEM SW3
    NONE: No switches linked with key ID5
    MEM SW1: M1 switch linked with key ID5
    MEM SW2: M2 switch linked with key ID5
    MEM SW3: Related switch does not exist
    -
    Mem SW No. w/KeyID6
    Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2 or MEM SW3
    NONE: No switches linked with key ID6
    MEM SW1: M1 switch linked with key ID6
    MEM SW2: M2 switch linked with key ID6
    MEM SW3: Related switch does not exist
    -
    Mem SW No. w/KeyID7
    Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2 or MEM SW3
    NONE: No switches linked with key ID7
    MEM SW1: M1 switch linked with key ID7
    MEM SW2: M2 switch linked with key ID7
    MEM SW3: Related switch does not exist
    -

    OK:
    On the tester display, it is confirmed that the memory call is registered.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK


9. CHECK MEMORY CALL FUNCTION (SEAT MEMORY CALL)
  1. With a recognition code stored in memory, open the driver door after performing an entry unlock operation or pressing the transmitter unlock switch. Check that the driver side power seat moves to the memorized position (Click here).

    OK:
    Driver side power seat moves to the memorized position.



NG
GO TO PROBLEM SYMPTOMS TABLE (Wireless-linked Return Function does not Operate) (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← Power Seat Position is not Memorized (from Aug 2014)Wireless Transmitter Memory Function does not Operate (from Aug 2014) →