Power Seat Position is not Memorized
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the seat memory SET switch and a memory switch (M1 or M2) are pressed simultaneously, the main body ECU commands the position control ECU through CAN communication to record the value of each position sensor.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.
| 1. CHECK FRONT POWER SEAT CONTROL FUNCTION |
Check that each function of the power seat operates normally by using the front power seat switches.
- OK:
- Each function of power seat operates normally by using seat switches.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (SEAT POSITION MEMORY) |
Use the seat memory switch to record the seat position (Click here).
- NOTICE:
- The seat position will not be recorded if the SET switch and both memory switches are pressed simultaneously.
- If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
- The seat position will not be recorded if the SET switch and both memory switches are pressed simultaneously.
Using the intelligent tester, read the Data List (Click here).
Driver Seat Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Seat Memory No1
Seat position memorized with M1 switch / Mem or Not Mem
Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2
Seat position memorized with M2 switch / Mem or Not Mem
Mem: Memorized
Not Mem: Not memorized
-
- OK:
- "Mem" is displayed on the tester.
|
|
||||
| OK | ||
| ||
| 3. READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH) |
Using the intelligent tester, read the Data List (Click here).
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
M1 Switch
Seat memory switch M1 signal / ON or OFF
ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
-
M2 Switch
Seat memory switch M2 signal / ON or OFF
ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
-
SET Switch
Seat memory switch SET signal / ON or OFF
ON: Seat memory switch SET on
OFF: Seat memory switch SET off
-
- OK:
- On intelligent tester screen, each item changes between ON and OFF according to above chart.
|
|
||||
| OK | |
| 4. CHECK FRONT POWER SEAT SWITCH (OPERATION) |
Replace the front power seat switch with a new one or normally operating one.
Use the seat memory switch to record the seat position (Click here).
Refer to the Data List for the driver seat and check that the memory operation is completed normally.
- OK:
- Seat position is recorded normally.
|
|
||||
| OK | ||
| ||
| 5. INSPECT SEAT MEMORY SWITCH |
Remove the seat memory switch (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
3 (M1) - 1 (E)
Seat memory switch M1 pressed
Below 1 Ω
4 (M2) - 1 (E)
Seat memory switch M2 pressed
Below 1 Ω
2 (MRY) - 1 (E)
Seat memory switch SET pressed
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - MAIN BODY ECU AND BODY GROUND) |
Disconnect the K9*1 or J10*2 switch connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Disconnect the G63 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
G63-25 (M1) - K9-3 (M1)
Always
Below 1 Ω
G63-27 (M2) - K9-4 (M2)
Always
Below 1 Ω
G63-26 (MM) - K9-2 (MRY)
Always
Below 1 Ω
K9-1 (E) - Body ground
Always
Below 1 Ω
G63-25 (M1) - Body ground
Always
10 kΩ or higher
G63-27 (M2) - Body ground
Always
10 kΩ or higher
G63-26 (MM) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
G63-25 (M1) - J10-3 (M1)
Always
Below 1 Ω
G63-27 (M2) - J10-4 (M2)
Always
Below 1 Ω
G63-26 (MM) - J10-2 (MRY)
Always
Below 1 Ω
J10-1 (E) - Body ground
Always
Below 1 Ω
G63-25 (M1) - Body ground
Always
10 kΩ or higher
G63-27 (M2) - Body ground
Always
10 kΩ or higher
G63-26 (MM) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
