2013-2015 Land Cruiser Prado · Service Manual Brake

C1403 Rear Speed Sensor RH Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
C1403
C1404
One of the following conditions is met:
  1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.
  2. At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
  3. At a vehicle speed less than 10 km/h (6 mph), outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more.
  1. Rear speed sensor RH/LH
  2. Rear speed sensor rotor RH/LH
  3. Sensor installation
C1273
C1274
Stored only during test mode.
  1. Rear speed sensor RH/LH
  2. Rear speed sensor rotor RH/LH
  3. Sensor installation

HINT:
  1. DTCs C1403 and C1273 are for the rear speed sensor RH.
  2. DTCs C1404 and C1274 are for the rear speed sensor LH.


INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal after cleaning or replacement (Click here).


1. CHECK REAR SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C144929E49
    Check the speed sensor installation (Click here).

    OK:
    There is no clearance between the sensor and the rear axle.
    The installation nut is tightened properly.

    Text in Illustration 
    *1
    Rear Speed Sensor
    *a
    No clearance
    *b
    OK
    *c
    NG



NG
INSTALL REAR SPEED SENSOR CORRECTLY
OK


2. INSPECT REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


3. INSPECT REAR SPEED SENSOR ROTOR
  1. Remove the rear axle hub and bearing assembly (Click here).

  1. Check the speed sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    HINT:
    The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
    If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.



NG
CLEAN OR REPLACE REAR SPEED SENSOR ROTOR
OK


4. READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    RL Wheel Speed
    Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE REAR SPEED SENSOR
  1. Replace the rear speed sensor (Click here).


NEXT


6. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more or at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



NG
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (Click here)
OK

END


← C1403 Rear Speed Sensor RH Malfunction (+ C1273, C1274, C1404) (Aug 2013 – Jul 2014)C1405 Open or Short in Front Speed Sensor RH Circuit (+ C1406) (Aug 2013 – Jul 2014) →