2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Power Seat Position is not Memorized

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the seat memory SET switch and a memory switch (M1 or M2) are pressed simultaneously, the main body ECU commands the position control ECU through CAN communication to record the value of each position sensor.

WIRING DIAGRAM

B205120E02

INSPECTION PROCEDURE

NOTICE:
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.


1. CHECK FRONT POWER SEAT CONTROL FUNCTION
  1. Check that each function of the power seat operates normally by using the front power seat switches.

    OK:
    Each function of power seat operates normally by using seat switches.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (SEAT POSITION MEMORY)
  1. Use the seat memory switch to record the seat position (Click here).

    NOTICE:
    1. The seat position will not be recorded if the SET switch and both memory switches are pressed simultaneously.
    2. If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

  1. Using the intelligent tester, read the Data List (Click here).

    Driver Seat 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Seat Memory No1
    Seat position memorized with M1 switch / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -
    Seat Memory No2
    Seat position memorized with M2 switch / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -

    OK:
    "Mem" is displayed on the tester.



NG
Go to step 3
OK

END

3. READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)
  1. Using the intelligent tester, read the Data List (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    M1 Switch
    Seat memory switch M1 signal / ON or OFF
    ON: Seat memory switch M1 on
    OFF: Seat memory switch M1 off
    -
    M2 Switch
    Seat memory switch M2 signal / ON or OFF
    ON: Seat memory switch M2 on
    OFF: Seat memory switch M2 off
    -
    SET Switch
    Seat memory switch SET signal / ON or OFF
    ON: Seat memory switch SET on
    OFF: Seat memory switch SET off
    -

    OK:
    On intelligent tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 5
OK


4. CHECK FRONT POWER SEAT SWITCH (OPERATION)
  1. Replace the front power seat switch with a new one or normally operating one.

  1. Use the seat memory switch to record the seat position (Click here).

  1. Refer to the Data List for the driver seat and check that the memory operation is completed normally.

    OK:
    Seat position is recorded normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (FRONT POWER SEAT SWITCH WAS DEFECTIVE)

5. INSPECT SEAT MEMORY SWITCH

  1. B199457E01
    Remove the seat memory switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (M1) - 1 (E)
    Seat memory switch M1 pressed
    Below 1 Ω
    4 (M2) - 1 (E)
    Seat memory switch M2 pressed
    Below 1 Ω
    2 (MRY) - 1 (E)
    Seat memory switch SET pressed
    Below 1 Ω



NG
REPLACE SEAT MEMORY SWITCH (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the K9*1 or J10*2 switch connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the G63 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    G63-25 (M1) - K9-3 (M1)
    Always
    Below 1 Ω
    G63-27 (M2) - K9-4 (M2)
    Always
    Below 1 Ω
    G63-26 (MM) - K9-2 (MRY)
    Always
    Below 1 Ω
    K9-1 (E) - Body ground
    Always
    Below 1 Ω
    G63-25 (M1) - Body ground
    Always
    10 kΩ or higher
    G63-27 (M2) - Body ground
    Always
    10 kΩ or higher
    G63-26 (MM) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    G63-25 (M1) - J10-3 (M1)
    Always
    Below 1 Ω
    G63-27 (M2) - J10-4 (M2)
    Always
    Below 1 Ω
    G63-26 (MM) - J10-2 (MRY)
    Always
    Below 1 Ω
    J10-1 (E) - Body ground
    Always
    Below 1 Ω
    G63-25 (M1) - Body ground
    Always
    10 kΩ or higher
    G63-27 (M2) - Body ground
    Always
    10 kΩ or higher
    G63-26 (MM) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← Front Power Seat does not Operate with Front Power Seat Switch (from Aug 2014)Power Seat Position is not Memorized (from Aug 2014) →