2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


PARKING ASSIST MONITOR DIAGNOSIS SYSTEM
  1. For parking assist monitor system diagnosis, signals received by the parking assist ECU can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the multi-display assembly.

    NOTICE:
    Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here).

    HINT:
    The displayed screens and items may differ depending on vehicle specifications.


DIAGNOSIS SCREEN TRANSITION (during parking assist ECU initialization)
E282812E01
E248984

DIAGNOSIS SCREEN TRANSITION (after parking assist ECU initialization)
E282813E01
E282814

DIAGNOSTIC MODE
  1. Start diagnostic mode.

    1. for Navigation Receiver Type: Click here
    2. for Radio and Display Type: Click here

  2. Failure diagnosis.

    1. for Navigation Receiver Type: Click here
    2. for Radio and Display Type: Click here

  3. E285877
    System check (check using system check mode screen).
    1. for Navigation Receiver Type: Click here
    2. for Radio and Display Type: Click here

  4. Finish diagnostic mode.

    1. for Navigation Receiver Type: Click here
    2. for Radio and Display Type: Click here


SIGNAL CHECK (parking assist ECU input signal)

  1. Start diagnostic mode.

    1. for Navigation Receiver Type: Click here
    2. for Radio and Display Type: Click here

    1. E271944
      Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

    2. E271945
      Select "Camera Setting" on the "Function Check/Setting I" screen.

      HINT:
      After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.
      Parking Assist ECU Initialization
      Screen Transition
      Not performed
      "Signal Check" screen
      Performed
      "Mode Setting" screen

    3. E246954
      When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Signal Check" screen.

      HINT:
      To select a grayed out item, select and hold the item for 2 seconds or more.

  2. E285879
    Signal Check:

    1. On the "Signal Check" screen, it is possible to inspect the state of signals sent to the parking assist ECU and check the settings.

      Item
      Inspection Detail
      Note
      CAN
      CAN signal input
      When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
      SHIFT
      Shift position signal input
      CAMERA SW
      Front and side monitor main switch signal input
      MIRROR SW
      Outer rear view mirror retract signal input
      HANDLE
      Steering position signal input
      DEST
      Destination code signal input
      BODY
      Vehicle body information input
      T/M
      Transmission signal input
      D-CAM SET
      Driver side camera information signal input

      HINT:
      1. When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.
      2. If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".

  3. CAN inspection:

    HINT:
    If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs (Click here).

  4. SHIFT inspection:

    HINT:
    If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs (Click here).

  5. CAMERA SW inspection:

    1. Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".

    2. Check that "OK" (blue) changes to "CHK" (red). Press the front and side monitor main switch assembly and check that "CHK" (red) returns to "OK" (blue).

      HINT:
      If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to Problem Symptoms Table ("CHK" message(s) are displayed on the [Signal Check] screen) (Click here).

  6. MIRROR SW inspection:

    1. Check that "OK" (blue) is displayed for "MIRROR SW" and select "OK".

    2. Check that "OK" (blue) changes to "CHK" (red). Press the outer mirror switch and check that "CHK" (red) returns to "OK" (blue).

      HINT:
      After operating the outer mirror retract switch, if the outer mirror remains in the retracted state, return the outer mirror to the driving position. If "CHK" (red) remains displayed or the "MIRROR SW" inspection result is not normal, perform troubleshooting according to Problem Symptoms Table ("CHK" message(s) are displayed on the [Signal Check] screen) (Click here).

  7. HANDLE inspection:

    1. Check that the steering position is displayed correctly for "HANDLE" ("LHD" [blue] or "RHD" [blue]).

      HINT:
      If the steering position is not displayed correctly or "CHK" (red) is displayed, perform troubleshooting according to Problem Symptom Table ("CHK" message(s) are displayed on the Signal Check screen) (Click here).

  8. DEST inspection:

    1. Check that displayed for "DEST" is matched destination code for vehicles.

      HINT:
      If the destination is not displayed correctly or "CHK" (red) is displayed, perform troubleshooting according to Problem Symptom Table ("CHK" message(s) are displayed on the Signal Check screen) (Click here).

  9. BODY inspection:

    1. Check that displayed for "BODY" is matched vehicle body information.

  10. T/M inspection:

    1. Check that displayed for "T/M" is matched transmission for vehicles.

  11. D-CAM SET inspection:

    1. Check that "WITH" (blue) is displayed for "D-CAM SET".

  12. Finish diagnostic mode.

    1. for Navigation Receiver Type: Click here
    2. for Radio and Display Type: Click here


CALIBRATION WHEN SERVICING VEHICLE

NOTICE:
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here).

← TERMINALS OF ECU (from Aug 2014)DIAGNOSIS SYSTEM (from Aug 2014) →