DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| SIDE MONITOR DIAGNOSIS SYSTEM |
For side monitor system diagnosis, signals received by the parking assist ECU can be checked and the side monitor system can be calibrated, adjusted and checked using the multi-display assembly.
- NOTICE:
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (Click here).
- HINT:
- The displayed screens and items may differ depending on vehicle specifications.
| DIAGNOSIS SCREEN TRANSITION (during parking assist ECU initialization) |




| DIAGNOSIS SCREEN TRANSITION (after parking assist ECU initialization) |




| DIAGNOSTIC MODE |
Start diagnostic mode.
- w/ Navigation System: Click here
- w/o Navigation System: Click here
- w/ Navigation System: Click here
Failure diagnosis.
- w/ Navigation System: Click here
- w/o Navigation System: Click here
- w/ Navigation System: Click here
System check (check using system check mode screen).

- w/ Navigation System: Click here
- w/o Navigation System: Click here
- w/ Navigation System: Click here
Finish diagnostic mode.
- w/ Navigation System: Click here
- w/o Navigation System: Click here
- w/ Navigation System: Click here
| SIGNAL CHECK (parking assist ECU input signal) |
Start diagnostic mode.
- w/ Navigation System: Click here
- w/o Navigation System: Click here
Select "Function Check/Setting" on the "Service Menu screen" to display the Function Check/Setting screen.

Select "Camera Setting" on the "Function Check/Setting I" screen.

- HINT:
- After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.
Parking Assist ECU Initialization
Screen Transition
Not performed
"Signal Check" screen
Performed
"Mode Setting" screen
When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Signal Check" screen.

- HINT:
- To select a grayed out item, select and hold the item for 2 seconds or more.
- w/ Navigation System: Click here
Start diagnostic mode.
- w/ Navigation System: Click here
- w/o Navigation System: Click here
Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting" screen.

Select "Camera Setting" on the "Function Check/Setting I" screen.

- HINT:
- After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.
Parking Assist ECU Initialization
Screen Transition
Not performed
"Signal Check" screen
Performed
"Mode Setting" screen
When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Signal Check" screen.

- HINT:
- To select a grayed out item, select and hold the item for 2 seconds or more.
- w/ Navigation System: Click here
Signal Check:

On the "Signal Check" screen, it is possible to inspect the state of signals sent to the parking assist ECU and check the settings.
Item
Inspection Detail
Note
CAN
CAN signal input
When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
SHIFT
Shift position signal input
CAMERA SW
Front and side monitor main switch signal input
MIRROR SW
Outer rear view mirror retract signal input
HANDLE
Steering position signal input
DEST
Destination code signal input
BODY
Vehicle body information input
T/M
Transmission signal input
D-CAM SET
Driver side camera information signal input
- HINT:
- When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.
- If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".
- When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.
CAN inspection:
- HINT:
- If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs (Click here).
SHIFT inspection:
- HINT:
- If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs (Click here).
CAMERA SW inspection:
Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".
Check that "OK" (blue) changes to "CHK" (red). Press the front and side monitor main switch assembly and check that "CHK" (red) returns to "OK" (blue).
- HINT:
- If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen) (Click here).
MIRROR SW inspection:
Check that "OK" (blue) is displayed for "MIRROR SW" and select "OK".
Check that "OK" (blue) changes to "CHK" (red). Press the outer mirror switch and check that "CHK" (red) returns to "OK" (blue).
- HINT:
- After operating the outer mirror retract switch, if the outer mirror remains in the retracted state, return the outer mirror to the driving position. If "CHK" (red) remains displayed or the "MIRROR SW" inspection result is not normal, perform troubleshooting according to Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen) (Click here).
HANDLE inspection:
Check that the steering position is displayed correctly for "HANDLE" ("LHD" (blue) or "RHD" (blue)).
- HINT:
- If the steering position is not displayed correctly or "CHK" (red) is displayed, perform troubleshooting according to Problem Symptom Table ("CHK" message(s) are displayed on the Signal Check screen) (Click here).
DEST inspection:
Check that displayed for "DEST" is matched destination code for vehicles.
- HINT:
- If the destination is not displayed correctly or "CHK" (red) is displayed, perform troubleshooting according to Problem Symptom Table ("CHK" message(s) are displayed on the Signal Check screen) (Click here).
BODY inspection:
Check that displayed for "BODY" is matched vehicle body information.
T/M inspection:
Check that displayed for "T/M" is matched transmission for vehicles.
D-CAM SET inspection:
Check that "WITH" (blue) is displayed for "D-CAM SET".
Finish diagnostic mode.
- w/ Navigation System: Click here
- w/o Navigation System: Click here
- w/ Navigation System: Click here
| CALIBRATION WHEN SERVICING VEHICLE |
- NOTICE:
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (Click here).