2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

Cruise Control Switch Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This circuit sends a signal to the ECM depending on the cruise control switch condition. The battery supplies positive (+) battery voltage to the cruise control switch. Terminal 11 (CCS)*1 or 14 (CCS)*2 of the ECM receives the voltage which varies according to the switch condition.
  1. *1: for 1GR-FE
  2. *2: for 1KD-FTV, 2TR-FE

WIRING DIAGRAM

E284932E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Use the Data List to check if the cruise control switch is functioning properly (Click here).

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main SW M-CPU
    Cruise control switch (Main CPU) / ON or OFF
    ON: Cruise control switch on
    OFF: Cruise control switch off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -SET switch signal / ON or OFF
    ON: -SET switch on
    OFF: -SET switch off
    -
    RES/ACC Switch
    +RES switch signal / ON or OFF
    ON: +RES switch on
    OFF: +RES switch off
    -

    OK:
    On screen, each item changes between ON and OFF according to above chart.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Remove the spiral cable sub-assembly (Click here).

  1. E176804E05
    If there are any defects as follows, replace the spiral cable with a new one: scratches, cracks, dents or chips on the connector or spiral cable.

  1. Check the spiral cable.

    1. Set the spiral cable to the center position (Click here).

    2. Rotate the spiral cable 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise and measure the resistance according to the value(s) in the table below.

      NOTICE:
      As the spiral cable may break, do not rotate the spiral cable more than the specified amount.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (CCS) - 1 (CCS)
      Always
      Below 1 Ω
      4 (ECC) - 2 (ECC)

    3. Set the spiral cable to the center position and rotate the spiral cable 2.5 times clockwise. Then, while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (CCS) - 1 (CCS)
      Always
      Below 1 Ω
      4 (ECC) - 2 (ECC)



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3. INSPECT CRUISE CONTROL SWITCH WIRE

  1. E178683E18
    Disconnect the z7 spiral cable connector.

  1. Disconnect the A switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z7-3 (CCS) - A-3 (CCS)
    Always
    Below 2.5 Ω
    z7-4 (ECC) - A-1 (ECC)
    z7-3 (CCS) - Body ground
    Always
    1 MΩ or higher
    z7-4 (ECC) - Body ground



NG
REPLACE CRUISE CONTROL SWITCH WIRE
OK


4. INSPECT CRUISE CONTROL SWITCH

  1. Remove the cruise control switch (Click here).B215369E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (CCS) - 1 (ECC)
    Cruise control switch on
    Below 2.5 Ω
    Cruise control switch off
    1 MΩ or higher
    +RES switch held on
    235 to 245 Ω
    -SET switch held on
    617 to 643 Ω
    CANCEL switch held on
    1509 to 1571 Ω



NG
REPLACE CRUISE CONTROL SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
  1. Disconnect the G40 spiral cable connector.

  1. Disconnect the G56*1, G57*2 or G60*3 ECM connector.

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV
    3. *3: for 2TR-FE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    G40-1 (CCS) - G56-11 (CCS)
    Always
    Below 1 Ω
    G40-2 (ECC) - Body ground
    G40-1 (CCS) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    G40-1 (CCS) - G60-14 (CCS)
    Always
    Below 1 Ω
    G40-2 (ECC) - Body ground
    G40-1 (CCS) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    G40-1 (CCS) - G57-14 (CCS)
    Always
    Below 1 Ω
    G40-2 (ECC) - Body ground
    G40-1 (CCS) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 2TR-FE)
    B
    OK (for 1KD-FTV)
    C
    NG
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← Cruise Control Switch Circuit (Aug 2013 – Jul 2014)Cruise Main Indicator Light Circuit (Aug 2013 – Jul 2014) →