2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. A222363
    Remove the 8 bolts and hood.

    NOTICE:
    If the hood support is detached from the ball joint, it becomes non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.


3. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)

4. REMOVE FRONT BUMPER LOWER COVER
  1. Remove the clip, 5 bolts and front bumper lower cover.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover.


6. REMOVE TRANSMISSION UNDER COVER
  1. Remove the 2 bolts and transmission under cover.


7. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover.


8. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A218364
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A218365E01

    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Vent Plug
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


9. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


10. DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket and then drain the manual transmission oil.

  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


11. DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


12. DRAIN POWER STEERING FLUID

13. REMOVE RADIATOR ASSEMBLY
(Click here)

14. REMOVE BATTERY HOLD DOWN CLAMP
  1. Remove the 2 nuts and battery hold down clamp.


15. REMOVE BATTERY

16. REMOVE BATTERY TRAY

17. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A239587E01
    Remove the 2 nuts.
    Text in Illustration 
    *1
    No. 1 Engine Cover Hook
    *2
    No. 3 Engine Cover Bracket

  1. Detach the 2 No. 1 engine cover hooks from the No. 3 engine cover bracket and remove the No. 1 engine cover.


18. REMOVE NO. 1 AIR CLEANER HOSE

  1. A223211
    Loosen the 2 hose clamps and remove the No. 1 air cleaner hose.


19. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

A246272E02
  1. except Cold Area Specification Vehicles:
    Detach the 2 clamps and disconnect the mass air flow meter connector.

    Text in Illustration 
    *A
    except Cold Area Specification Vehicles
    *B
    for Cold Area Specification Vehicles

  1. for Cold Area Specification Vehicles:
    Detach the 3 clamps and disconnect the mass air flow meter connector.

  1. Detach the 4 clamps and remove the air cleaner cap sub-assembly.


20. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

21. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A223214
    Remove the 3 bolts and air cleaner case sub-assembly.


22. REMOVE COMPRESSOR OUTLET ELBOW

  1. A223215
    Detach the 3 wire harness clamps.

  1. Remove the bolt and wire harness bracket.

  1. A220719
    Loosen the hose clamp and remove the 2 bolts and compressor outlet elbow.


23. REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (for Cold Area Specification Vehicles)
  1. Disconnect the viscous heater connector.

  1. A223522
    Disconnect the water by-pass hose and water hose.

  1. A223524
    Remove the 2 bolts and viscous heater with magnet clutch.


24. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

  1. A223525
    Remove the 4 bolts and No. 1 viscous heater bracket.


25. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

  1. A223526
    Disconnect the compressor connector.

  1. Remove the 4 bolts and disconnect the cooler compressor.


26. DISCONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

  1. A239589
    Remove the bolt and disconnect the No. 4 vacuum transmitting pipe.


27. DISCONNECT INTERCOOLER AIR HOSE

  1. A239590
    Loosen the hose clamp and disconnect the intercooler air hose.


28. REMOVE NO. 1 INTAKE PIPE

  1. A239592
    Disconnect the 2 connectors from the intake air temperature sensor and throttle position sensor.

  1. Detach the 2 wire harness clamps.

  1. A239593
    Loosen the 2 hose clamps of the No. 1 air hose.

  1. Remove the 2 bolts and No. 1 intake pipe.


29. REMOVE FUEL FILTER ASSEMBLY
(Click here)

30. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A239651
    Remove the 3 bolts and disconnect the vane pump oil reservoir.


31. DISCONNECT PRESSURE FEED TUBE ASSEMBLY

  1. A224072
    Disconnect the power steering oil pressure switch connector.

  1. A224081
    Remove the union bolt and gasket and disconnect the pressure feed tube.


32. REMOVE NO. 1 ENGINE COVER BRACKET

  1. A239349
    Remove the bolt and No. 1 engine cover bracket.


33. REMOVE NO. 3 ENGINE COVER BRACKET

  1. A239350
    Remove the 2 nuts and No. 3 engine cover bracket.


34. REMOVE ENGINE COVER BRACKET INSULATOR

  1. A239397
    Remove the 2 nuts and 2 engine cover bracket insulators.


35. REMOVE NO. 4 ENGINE COVER BRACKET

  1. A239426
    Remove the bolt and No. 4 engine cover bracket.


36. DISCONNECT INLET HEATER WATER HOSE

  1. A239351
    Disconnect the inlet heater water hose.


37. DISCONNECT WATER PIPE AND HOSE SUB-ASSEMBLY

  1. A239352
    Remove the bolt and disconnect the water pipe and hose.


38. DISCONNECT FUEL HOSE

  1. A239353
    Disconnect the fuel hose from the fuel supply pump.


39. DISCONNECT NO. 2 FUEL HOSE

  1. A239354
    Disconnect the No. 2 fuel hose from the No. 3 nozzle leakage pipe.


40. REMOVE GLOVE COMPARTMENT DOOR SUB-ASSEMBLY
(Click here)

41. DISCONNECT ENGINE WIRE
  1. Remove the No. 1 relay block cover.

  1. A224073
    Remove the nut and detach the 2 claws.

  1. A239355
    Disconnect the 4 injection driver connectors.

  1. A239356
    Disconnect the connector and detach the clamp.

  1. A224077
    Remove the bolt.

  1. A239357
    Remove the nut and disconnect the engine wire.

  1. A224078
    Remove the bolt and disconnect the wire harness protector.

  1. A224079E01
    Remove the bolt and disconnect the engine wire.
    Text in Illustration 
    *A
    w/ KDSS
    *B
    w/o KDSS

  1. A225400E01
    Detach the clamp and disconnect the 9 connectors.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  1. A225401E01
    Detach the grommet from the wire harness support.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  1. A225402E01
    Detach the 4 claws and remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD


42. REMOVE STARTER ASSEMBLY (for 2.2 kW Type)
  1. Remove the terminal cap.

  1. A224849
    Remove the nut and disconnect the starter wire.

  1. Disconnect the starter connector.

  1. A222635
    for Automatic Transmission:
    Remove the bolt, 2 nuts and starter assembly.

  1. A222636
    for Manual Transmission:
    Remove the bolt, nut and starter assembly.


43. REMOVE STARTER ASSEMBLY (for 2.7 kW Type)
  1. Remove the terminal cap.

  1. A224848
    Remove the nut and disconnect the starter wire.

  1. Disconnect the starter connector.

  1. A246032
    for Automatic Transmission:
    Remove the bolt, 2 nuts and starter assembly.

  1. A223731
    for Manual Transmission:
    Remove the bolt, nut and starter assembly.


44. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)

45. REMOVE FRONT PROPELLER SHAFT ASSEMBLY

  1. C098708E07
    Place matchmarks on the propeller shaft flange and differential.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft assembly.

  1. C098709E10
    Place matchmarks on the propeller shaft flange and transfer flange.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 nuts, 4 washers and front propeller shaft assembly.


46. REMOVE PROPELLER SHAFT ASSEMBLY

  1. C219704E01
    Place matchmarks on the propeller shaft flange and transfer flange.
    Text in Illustration 
    *A
    for 3 Door
    *B
    for 5 Door
    *a
    Matchmark

  1. Remove the 4 nuts and 4 washers.

  1. C219705E01
    Place matchmarks on the propeller shaft flange and differential flange.
    Text in Illustration 
    *A
    for 3 Door
    *B
    for 5 Door
    *a
    Matchmark

  1. Remove the 4 nuts, 4 bolts and 4 washers.

  1. Remove the propeller shaft.


47. REMOVE OIL PAN INSULATOR

  1. A225336
    Remove the 2 bolts and oil pan insulator.


48. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
(Click here)

49. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission)

C218118
  1. Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.

    HINT:
    If it is difficult to reach the setting bolts with the wrench, raise or lower the transmission jack until there is sufficient space for the wrench.


50. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

51. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.

  1. A225338
    Remove the 4 bolts and rear No. 1 engine mounting insulator.


52. REMOVE ENGINE ASSEMBLY

  1. A224109E01
    Install 2 engine hangers with 2 bolts as shown in the illustration.

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    Part No.

    No. 1 Engine Hanger
    12284-30020
    No. 2 Engine Hanger
    12282-67030
    Bolt
    91552-81014 and 91642-81030

    NOTICE:
    Install the engine hangers with new bolts.

  1. Attach an engine sling device and hang the engine with a chain block.

  1. A224146E01
    Remove the 4 bolts and 4 nuts.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side

  1. Remove the engine by operating the engine sling device and chain block.


53. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

C215513E01
  1. Place matchmarks on the clutch cover and flywheel.

    Text in Illustration 
    *a
    Matchmark

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


54. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, the pressure plate and the surface of the flywheel away from oil and foreign matter.


55. REMOVE CRANKSHAFT PULLEY COVER

  1. A239358
    Remove the 2 bolts and crankshaft pulley cover.


56. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. A225337E01
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. Remove the 8 bolts and flywheel.


57. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)

  1. A225337E01
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A225158
    Remove the 8 bolts, the rear drive plate spacer, the pump impeller drive plate and the flywheel and ring gear.


58. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.


59. INSTALL ENGINE TO ENGINE STAND

60. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.


61. REMOVE FRONT ENGINE MOUNTING INSULATOR

  1. A247847E01
    Detach the clamp and disconnect the 2 hoses.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side

  1. Remove the 2 nuts and 2 front engine mounting insulators.

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →