2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT SEAT ASSEMBLY (for RHD)
  1. for Manual Seat:
    Remove the front seat assembly (Click here).

  1. for Walk in Seat:
    Remove the front seat assembly (Click here).


3. REMOVE CONSOLE BOX ASSEMBLY (for RHD)
  1. for Automatic Transmission:
    Remove the console box assembly (Click here).

  1. for Manual Transmission:
    Remove the console box assembly (Click here).

  1. w/ Refrigerated Cool Box:
    Remove the console box assembly (Click here).


4. REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)
  1. for LH Side:
    Remove the rear No. 1 seat assembly (Click here).

  1. for RH Side:
    Remove the rear No. 1 seat assembly (Click here).


5. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

B238732E01
  1. Put protective tape around the door scuff plate.

  1. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


6. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


7. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.


8. REMOVE MAT SET PLATE COVER

B240525E01

HINT:
Use the same procedure for all mat set plate covers.

  1. Using a screwdriver, detach the 2 claws and remove the mat set plate cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


9. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B240526
  1. Remove the 5 screws.

  1. Detach the 6 claws and remove the rear floor mat rear support plate.


10. REMOVE QUARTER TRIM COVER HOLE LH

B240533
  1. Detach the 2 claws and 2 guides and remove the quarter trim cover hole.


11. REMOVE REAR FLOOR CARPET ASSEMBLY

B240527
  1. Remove the rear floor carpet.


12. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

B181695

HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.

  1. Remove the luggage compartment trim hook by turning it clockwise.


13. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

B240528E01

HINT:
Use the same procedure for the other tonneau cover holder cap.

  1. Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


14. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

B240051E01

HINT:
Use the same procedure for the other front deck side trim cover.

  1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


15. REMOVE QUARTER TRIM POCKET TRAY

B240553E01
  1. Put protective tape around the quarter trim pocket tray.

  1. Using a screwdriver, detach the 6 claws and 2 guides, and remove the quarter trim pocket tray.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


16. REMOVE OUTER LAP BELT ANCHOR COVER

B240529

HINT:
Use the same procedure for the other outer lap belt anchor cover.

  1. Detach the 3 claws and remove the outer lap belt anchor cover.


17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

B240531
  1. Remove the bolt and disconnect the front seat outer belt floor anchor.

  1. B240534
    Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

  1. Remove the 3 bolts and 2 screws.

  1. Detach the 9 claws and 12 clips and remove the deck trim side panel.

    B240536


18. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH

B240540
  1. Detach the 7 clips.

  1. B240541
    Detach the 4 claws and 2 guides, pass the rear No. 1 seat belt floor anchor through the rear quarter trim panel and remove the rear quarter trim panel.


19. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

  1. B238493
    Detach the 3 claws.

  1. Remove the fuel lid lock control cable assembly and fuel lid lock open lever sub-assembly.


20. REMOVE FRONT FLOOR CARPET ASSEMBLY

  1. B238503
    for LHD:

    1. Detach the 4 clamps and fold back the front floor carpet from the floor carpet hooks.

  1. B238505
    for RHD:

    1. Detach the 8 clamps and fold back the front floor carpet from the floor carpet hooks.


21. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

  1. B238500
    Turn the cable counterclockwise and remove the cable from the retainer.

  1. B238498
    Turn the lock retainer counterclockwise and remove the lock retainer.

  1. for LHD:

    1. Using a clip remover, detach the clamp labeled <A>.

    2. Detach the 11 clamps and remove the fuel lid lock control cable.

      B238497E01

  1. for RHD:

    1. Using a clip remover, detach the 3 clamps labeled <A>.

    2. Detach the 11 clamps and remove the fuel lid lock control cable.

      B238507E01

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →