Home › Drivetrain › G52F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY
REMOVAL
Removal / installation · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here ).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here ).
2.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
3.
REMOVE CONSOLE PANEL SUB-ASSEMBLY (for Separate Type)
for Manual Transmission: (Click here ) w/ Refrigerated Cool Box: (Click here )
4.
REMOVE CONSOLE BOX (for Bench Seat Type)
(Click here )
5.
REMOVE FRONT SEAT ASSEMBLY (for Bench Seat Type)
(Click here )
6.
REMOVE CENTER FLOOR CARPET ASSEMBLY (for Bench Seat Type)
Remove the 4 bolts and center floor carpet assembly.
7.
REMOVE NO. 1 SHIFT AND SELECT LEVER BOOT
Remove the 4 screws, 2 clips and boot.
Text in Illustration
*1
Clip
*2
Screw
8.
REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY
Cover the shift lever cap with a cloth.
Text in Illustration
*1
Cloth
*a
Down
*b
Counterclockwise
Press down on the shift lever cap and rotate it counterclockwise to remove it.
Pull out the shift lever to remove it.
9.
REMOVE TRANSFER CASE LOWER PROTECTOR
Remove the 4 bolts and transfer case lower protector.
10.
DRAIN MANUAL TRANSMISSION OIL
Remove the drain plug and gasket, and then drain the manual transmission oil.
Remove the filler plug and gasket.
Install a new gasket and the drain plug.
Torque:
37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
11.
REMOVE FRONT EXHAUST PIPE ASSEMBLY
Remove the front exhaust pipe (Click here ).
12.
REMOVE FRONT PROPELLER SHAFT ASSEMBLY
Remove the front propeller shaft (Click here ).
13.
REMOVE PROPELLER SHAFT ASSEMBLY
Remove the propeller shaft (Click here ).
14.
DISCONNECT WIRE HARNESS
Disconnect the 2 connectors and detach the 4 clamps.
15.
REMOVE TRANSFER AND MANUAL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY
Detach the clamp and disconnect the 3 breather hoses from the shift lever retainer and transfer adapter.
Remove the breather hose.
16.
DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY
Remove the 2 bolts and disconnect the release cylinder.
17.
REMOVE STARTER ASSEMBLY
Remove the starter (Click here ).
18.
REMOVE FRONT SUSPENSION MEMBER BRACKET LH
Remove the 4 bolts and member bracket.
19.
REMOVE FRONT SUSPENSION MEMBER BRACKET RH
Remove the 4 bolts and member bracket.
20.
REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Support the rear side of the transmission with a support stand.
Remove the 4 bolts of the rear No. 1 engine mounting insulator.
Remove the 4 bolts, 4 nuts and frame crossmember.
21.
REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Remove the 4 bolts and engine mounting insulator.
22.
REMOVE STIFFENER PLATE LH
Remove the 4 bolts and stiffener plate.
23.
REMOVE STIFFENER PLATE RH
Remove the 4 bolts and stiffener plate.
24.
REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY
Using a transmission jack, support the transmission.
Remove the support stand from the transmission.
Remove the 4 bolts and transmission.
25.
REMOVE TRANSFER ASSEMBLY
for 1KD-FTV:
Text in Illustration
*A
for 1KD-FTV, RA61F
*B
for 1KD-FTV, A750F
Remove the 8 bolts and 2 brackets.
except 1KD-FTV: Remove the 8 bolts and bracket.
Remove the transfer from the transmission.