2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

3. REMOVE CONSOLE PANEL SUB-ASSEMBLY (for Separate Type)
for Manual Transmission: (Click here)
w/ Refrigerated Cool Box: (Click here)

4. REMOVE CONSOLE BOX (for Bench Seat Type)
(Click here)

5. REMOVE FRONT SEAT ASSEMBLY (for Bench Seat Type)
(Click here)

6. REMOVE CENTER FLOOR CARPET ASSEMBLY (for Bench Seat Type)

  1. C251153
    Remove the 4 bolts and center floor carpet assembly.


7. REMOVE NO. 1 SHIFT AND SELECT LEVER BOOT

  1. C215582E01
    Remove the 4 screws, 2 clips and boot.
    Text in Illustration 
    *1
    Clip
    *2
    Screw


8. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY

  1. G021695E13
    Cover the shift lever cap with a cloth.
    Text in Illustration 
    *1
    Cloth
    *a
    Down
    *b
    Counterclockwise

  1. Press down on the shift lever cap and rotate it counterclockwise to remove it.

  1. Pull out the shift lever to remove it.


9. REMOVE TRANSFER CASE LOWER PROTECTOR
  1. Remove the 4 bolts and transfer case lower protector.


10. DRAIN MANUAL TRANSMISSION OIL

  1. D029129E01
    Remove the drain plug and gasket, and then drain the manual transmission oil.

  1. D029128E01
    Remove the filler plug and gasket.

  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


11. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the front exhaust pipe (Click here).


12. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
  1. Remove the front propeller shaft (Click here).


13. REMOVE PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft (Click here).


14. DISCONNECT WIRE HARNESS

  1. C215989
    Disconnect the 2 connectors and detach the 4 clamps.


15. REMOVE TRANSFER AND MANUAL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

  1. C215990
    Detach the clamp and disconnect the 3 breather hoses from the shift lever retainer and transfer adapter.

  1. Remove the breather hose.


16. DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

  1. C215983
    Remove the 2 bolts and disconnect the release cylinder.


17. REMOVE STARTER ASSEMBLY
  1. Remove the starter (Click here).


18. REMOVE FRONT SUSPENSION MEMBER BRACKET LH

  1. C215984
    Remove the 4 bolts and member bracket.


19. REMOVE FRONT SUSPENSION MEMBER BRACKET RH

  1. C215985
    Remove the 4 bolts and member bracket.


20. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
  1. Support the rear side of the transmission with a support stand.

  1. C215986
    Remove the 4 bolts of the rear No. 1 engine mounting insulator.

  1. C215987
    Remove the 4 bolts, 4 nuts and frame crossmember.


21. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

  1. C215988
    Remove the 4 bolts and engine mounting insulator.


22. REMOVE STIFFENER PLATE LH

  1. C215992
    Remove the 4 bolts and stiffener plate.


23. REMOVE STIFFENER PLATE RH

  1. C215991
    Remove the 4 bolts and stiffener plate.


24. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY
  1. Using a transmission jack, support the transmission.

  1. Remove the support stand from the transmission.

  1. C215993
    Remove the 4 bolts and transmission.


25. REMOVE TRANSFER ASSEMBLY

  1. C233861E01
    for 1KD-FTV:
    Text in Illustration 
    *A
    for 1KD-FTV, RA61F
    *B
    for 1KD-FTV, A750F
    Remove the 8 bolts and 2 brackets.

  1. C235226
    except 1KD-FTV:
    Remove the 8 bolts and bracket.

  1. Remove the transfer from the transmission.

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →