The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the fuel injector assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C50-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C2-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C51-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C4-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Inspect the fuel injector assembly (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL INJECTOR>INSPECTION).
Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).
OK
NG
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-2 - C154-4 (#10) | Always | Below 1 Ω |
| C2-2 - C154-3 (#20) | Always | Below 1 Ω |
| C51-2 - C154-2 (#30) | Always | Below 1 Ω |
| C4-2 - C154-1 (#40) | Always | Below 1 Ω |
| C50-2 or C154-4 (#10) - Body ground | Always | 10 kΩ or higher |
| C2-2 or C154-3 (#20) - Body ground | Always | 10 kΩ or higher |
| C51-2 or C154-2 (#30) - Body ground | Always | 10 kΩ or higher |
| C4-2 or C154-1 (#40) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the fuel injector assembly connectors.
Remove the INJ NO. 2 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-1 - INJ NO. 2 relay terminal 3 | Always | Below 1 Ω |
| C2-1 - INJ NO. 2 relay terminal 3 | Always | Below 1 Ω |
| C51-1 - INJ NO. 2 relay terminal 3 | Always | Below 1 Ω |
| C4-1 - INJ NO. 2 relay terminal 3 | Always | Below 1 Ω |
| C50-1 or INJ NO. 2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| C2-1 or INJ NO. 2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| C51-1 or INJ NO. 2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| C4-1 or INJ NO. 2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the INJ NO. 2 relay (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the INJ NO. 2 relay from the engine room relay block.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| INJ NO. 2 relay terminal 5 - Positive battery terminal | Always | Below 1 Ω |
| INJ NO. 2 relay terminal 5 or Positive battery terminal - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the INJ NO. 2 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| INJ No. 2 relay terminal 1 - Body ground | Always | Below 1 Ω |
OK
NG
Remove the INJ NO. 2 relay from the engine room relay block.
Remove the integration relay (EFI relay) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1B-4 - INJ NO. 2 relay terminal 2 | Always | Below 1 Ω |
| 1B-4 or INJ NO. 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
OK
NG