Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0014  Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)  P0015  Camshaft Position "B" - Timing Over-Retarded (Bank 1)  


DESCRIPTION

HINT:

If DTC P0014 or P0015 is output, check the VVT (Variable Valve Timing) system.


The Variable Valve Timing (VVT) system includes the ECM, camshaft timing oil control valve and camshaft timing exhaust gear. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the camshaft timing exhaust gear. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve based on the signals transmitted by several sensors. The camshaft timing exhaust gear regulates the exhaust camshaft angle using oil pressure through the camshaft timing oil control valve. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the VVT and crankshaft position sensors and performs feedback control. This is how the target exhaust valve timing is verified by the ECM.

A192077E81
2.563,4.573 2.844,4.271 2.844,4.271 3.604,4.271 false 3.177,4.823 3.323,5.052 3.323,5.052 3.854,5.052 false 4.479,0.813 6.146,1.052 1.667,0.24 10 false Camshaft Position Sensor 4.479,1.323 6.688,1.844 2.208,0.521 10 false Crankshaft Position Sensor 0.073,0.063 1.76,0.458 1.688,0.396 10 false VVT System: 2.333,1.99 3.938,2.417 1.604,0.427 10 false Target Valve Timing 2.333,1.292 4.156,1.865 1.823,0.573 10 false Actual Valve Timing 2.688,2.698 3.76,3.146 1.073,0.448 10 false Correction 2.823,3.208 3.604,3.646 0.781,0.438 10 false ECM 1.604,3.76 4.219,4.188 2.615,0.427 10 false Camshaft Timing Oil Control Valve 0.167,2.688 1.167,3.104 1,0.417 10 false Duty Cycle 4.479,1.823 7.073,2.385 2.594,0.563 10 false Mass Air Flow Meter sub-assembly 4.479,2.854 7.156,3.375 2.677,0.521 10 false Engine Coolant Temperature Sensor 4.479,2.344 6.354,2.771 1.875,0.427 10 false Throttle Position Sensor 4.479,3.354 6.365,3.75 1.885,0.396 10 false Vehicle Speed Sensor 0.375,4.271 1.979,4.656 1.604,0.385 10 false Engine Oil Pressure 3.656,4.219 6.302,4.448 2.646,0.229 10 false Camshaft Timing Exhaust Gear Assembly 3.885,4.958 5.333,5.552 1.448,0.594 10 false Exhaust Camshaft

DTC No. DTC Detection Condition Trouble Area
P0014 Exhaust valve timing is not adjusted in the advance range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


P0015 Exhaust valve timing is not adjusted in the retard range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM



MONITOR DESCRIPTION

The ECM optimizes the exhaust valve timing using the VVT (Variable Valve Timing) system to control the exhaust camshaft. The VVT system includes the ECM, camshaft timing oil control valve and camshaft timing exhaust gear.

The ECM sends a target duty cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the camshaft timing exhaust gear. The camshaft timing exhaust gear can advance or retard the exhaust camshaft.

If the difference between the target and actual exhaust valve timing is large, and changes in actual exhaust valve timing are small, the ECM interprets this as a camshaft timing exhaust gear being stuck and stores a DTC.

Example:

DTC P0014 is stored when the following conditions "A" and "B" are met:

(a)

It takes 5 seconds or more to change the valve timing by 5°CA (Condition "A").

(b)

The above condition "A" is met, for 60 seconds or more (Condition "B").


DTC P0015 is stored when the following conditions "C" and "D" are met:

(a)

It takes 5 seconds or more to change the valve timing by 5°CA (Condition "C").

(b)

The above condition "C" is met, for 9.5 seconds or more (Condition "D").


These DTCs indicate that the camshaft timing exhaust gear cannot operate properly due to camshaft timing oil control valve malfunctions or the presence of foreign objects in the camshaft timing oil control valve.


MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing oil control valve assembly (for exhaust side) and Camshaft timing exhaust gear assembly
Required Sensors/Components (Related) Crankshaft position sensor, Camshaft position sensor and Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A232050E10
1.361,2.351 1.596,2.498 0.235,0.147 10 [A] 1.88,2.062 2.114,2.208 0.235,0.147 10 [B] 3.012,1.001 3.247,1.148 0.235,0.147 10 [C] 4.049,2.316 4.284,2.463 0.235,0.147 10 [D] 4.285,3.14 4.519,3.287 0.235,0.147 10 [E] 5.445,2.218 5.680,2.365 0.235,0.147 10 [F]* 6.618,2.3 6.852,2.446 0.235,0.147 10 [G] 6.832,3.154 7.067,3.301 0.235,0.147 10 [H] 0.133,2.309 1.104,2.641 0.971,0.332 10 Ignition Switch ON 0.712,2.057 1.099,2.241 0.387,0.184 10 Idling 0.027,1.09 1.145,1.434 1.119,0.343 10 Approximately 60 km/h (37 mph) 0.17,0.376 1.123,0.541 0.952,0.165 10 Vehicle Speed 1.618,2.767 2.422,2.960 0.804,0.193 10 Warming up 2.561,2.776 3.805,2.923 1.244,0.147 10 10 minutes or more 2.552,3.393 3.847,3.567 1.295,0.174 10 3 minutes or more 6.723,2.596 6.33,3.458 6.33,3.458 6.246,3.458 false 4.159,2.617 3.836,3.479 3.836,3.479 3.766,3.479 false 2.379,0.025 7.035,0.542 4.656,0.517 10 *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 5.004,3.379 6.195,3.553 1.191,0.174 10 3 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0014 or P0015.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



14.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


15.

Idle the engine for 3 minutes or more [G].

16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
Timing Over-advanced
(Valve Timing is Out of Specified Range)
Timing Over-retarded
(Valve Timing is Out of Specified Range)
P0014 P0015

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014 OR P0015)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0014 or P0015 is output A
P0014 or P0015 and other DTCs are output B

HINT:

If any DTCs other than P0014 or P0015 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Turn the A/C on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1).


g.

Check the engine speed while operating the camshaft timing oil control valve assembly (for exhaust side) using the GTS.

OK:
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Read the output pending DTCs using the GTS.

OK:

No pending DTC output.




OK

END

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
a.
A337700E13
1.021,0.854 1.25,1.417 1.25,1.417 1.354,1.417 false 1.25,1.417 1.135,0.646 false 2.708,0.99 2.292,0.375 2.292,0.375 2.177,0.375 false 2.292,0.375 2.719,0.76 false 2.469,2.406 2.906,2.073 2.906,2.073 3.063,2.073 true 0.854,2.385 0.469,2.125 0.469,2.125 0.292,2.125 true 1.844,4.219 2.531,4.094 2.531,4.094 2.667,4.094 true 1.01,0.083 1.219,0.302 0.208,0.219 10 true *c 1.375,1.323 1.573,1.531 0.198,0.208 10 false *a 1.958,0.26 2.156,0.51 0.198,0.25 10 true *a 0.073,2.01 0.292,2.229 0.219,0.219 10 false *a 3.094,1.958 3.313,2.198 0.219,0.24 10 false *a 2.698,3.99 2.938,4.188 0.24,0.198 10 false *b

Remove the cylinder head cover.

Text in Illustration
*a Timing Mark
*b Groove
*c Approximately 13°


b.

Turn the crankshaft to align the timing marks of the crankshaft.


c.

Align the groove of the crankshaft pulley with the "0" position.


d.

Confirm whether the timing marks of the camshaft pulley and cylinder head cover are facing each other.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

The timing marks of the camshaft pulley and the cylinder head cover face each other when the groove of the crankshaft pulley is in the "0" position.




OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE)

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE)
a.

Inspect the camshaft timing oil control valve assembly (for exhaust side) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE)

6.INSPECT OIL CONTROL VALVE FILTER
a.

Remove the oil control valve filter (See pageEngine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).


b.

Check that the filter is not clogged.

OK:

The filter is not clogged.




OK

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

CLEAN OR REPLACE OIL CONTROL VALVE FILTER

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing exhaust gear assembly (See page Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015)
a.

Perform the Confirmation Driving Pattern.

OK:

No pending DTC is output and All Readiness is NORMAL.


HINT:

DTC P0014 or P0015 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.




OK

SYSTEM IS OK

NG