Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0230  Fuel Pump Primary Circuit  


DESCRIPTION

When a malfunction in the fuel pump circuit is detected, DTC P0230 is stored.

The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed among 3 settings. The fuel pump ECU also has a self-diagnosis function. Based on the fuel pump circuit condition, the fuel pump ECU outputs a diagnostic signal (DI) to the ECM, and the ECM determines if there is a malfunction in the fuel pump circuit.

DTC No. DTC Detection Condition Trouble Area
P0230 Either condition is met (1 trip detection logic):
·

When the fuel pump is operating:

-

The remaining fuel is 17 L or more.

-

The DI terminal output is low.



·

When the fuel pump is not operating:

-

The DI terminal output is high.



·

Open or short in fuel pump circuit

·

Fuel pump

·

Fuel pump ECU

·

ECM



MONITOR DESCRIPTION

To monitor the fuel pump circuit, the ECM checks the fuel pump control signal (FPC) and diagnostic signal (DI). The FPC voltage varies between approximately 0 V and approximately 12 V (duty signal). Based on the condition of the fuel pump ECU malfunction, the DI voltage varies between approximately 0 V and approximately 12 V. The ECM then compares the variance of the FPC voltage and DI voltage, and determines if the fuel pump circuit is malfunctioning. When the ECM determines that the fuel pump circuit is malfunctioning, a DTC is stored immediately.

WIRING DIAGRAM

for Automatic Transmission

A353963E03
1.177,0.646 1.469,0.802 0.292,0.156 10 false IGN 0.365,1.958 0.49,2.115 0.125,0.156 10 false 5 0.563,1.958 0.771,2.125 0.208,0.167 10 false 1A 0.365,3.75 0.49,3.906 0.125,0.156 10 false 1 1.354,1.958 1.479,2.115 0.125,0.156 10 false 3 1.354,3.75 1.479,3.906 0.125,0.156 10 false 1 0.563,3.75 0.771,3.917 0.208,0.167 10 false 1C 1.052,1.958 1.26,2.125 0.208,0.167 10 false 1A 1.052,3.75 1.26,3.917 0.208,0.167 10 false 1A 2.271,3.75 2.396,3.906 0.125,0.156 10 false 2 2.458,3.75 2.667,3.917 0.208,0.167 10 false 1B 2.458,1.958 2.667,2.125 0.208,0.167 10 false 1B 1.844,1.958 1.969,2.115 0.125,0.156 10 false 4 2.75,1.958 2.875,2.115 0.125,0.156 10 false 3 2.031,1.958 2.24,2.125 0.208,0.167 10 false 1B 1.344,3.938 2.448,4.26 1.104,0.323 10 false No. 1 Integration Relay 1.406,2.427 1.667,2.573 0.26,0.146 10 false IG2 0.74,3.083 1,3.229 0.26,0.146 10 false IG2 2.208,3.052 2.469,3.208 0.26,0.156 10 false EFI 2.802,2.427 3.073,2.583 0.271,0.156 10 false EFI 0.229,6.125 0.563,6.271 0.333,0.146 10 false P/I-B 0.885,6.875 1.365,7.063 0.479,0.188 10 false Battery 2.385,5.979 2.76,6.135 0.375,0.156 10 false IG2D 2.573,5.729 2.688,5.885 0.115,0.156 10 false 8 2.271,6.521 2.583,6.667 0.313,0.146 10 false G50 2.271,6.656 4.51,6.823 2.24,0.167 10 false Power Management Control ECU 2.573,0.365 2.677,0.521 0.104,0.156 10 false 2 3.344,0.365 3.448,0.521 0.104,0.156 10 false 1 2.573,0.823 2.677,0.979 0.104,0.156 10 false 5 3.344,0.823 3.448,0.979 0.104,0.156 10 false 3 2.75,1.323 3.229,1.49 0.479,0.167 10 false C/OPN 4,0.625 5.042,0.771 1.042,0.146 10 false Fuel Pump ECU 3.802,1.552 3.917,1.708 0.115,0.156 10 false 4 3.74,1.771 3.969,1.917 0.229,0.146 10 false S8 3.802,2.76 3.917,2.917 0.115,0.156 10 false 3 3.875,3.625 3.99,3.781 0.115,0.156 10 false 1 3.75,2.948 3.979,3.094 0.229,0.146 10 false S8 4.073,3.635 4.302,3.781 0.229,0.146 10 false S9 4.625,3.625 4.74,3.781 0.115,0.156 10 false 2 4.813,3.635 5.042,3.781 0.229,0.146 10 false S9 5.177,1.573 5.292,1.729 0.115,0.156 10 false 1 5.135,1.771 5.365,1.917 0.229,0.146 10 false S8 5.177,2.75 5.292,2.906 0.115,0.156 10 false 2 5.125,2.948 5.354,3.094 0.229,0.146 10 false S8 4.052,4.521 4.167,4.667 0.115,0.146 10 false 4 4.948,4.521 5.063,4.667 0.115,0.146 10 false 5 4.198,4.771 4.417,4.927 0.219,0.156 10 false B2 4.698,4.771 4.917,4.927 0.219,0.156 10 false E2 4.198,5.333 4.427,5.479 0.229,0.146 10 false S5 4.198,5.479 4.906,5.667 0.708,0.188 10 false Fuel Pump 5.979,0.302 6.104,0.448 0.125,0.146 10 false 5 5.875,0.521 6.156,0.667 0.281,0.146 10 false G55 6.229,0.521 6.458,0.677 0.229,0.156 10 false FC 5.979,1.552 6.104,1.698 0.125,0.146 10 false 4 5.865,1.771 6.146,1.917 0.281,0.146 10 false G55 6.229,1.771 6.542,1.927 0.313,0.156 10 false FPC 5.938,2.729 6.125,2.875 0.188,0.146 10 false 14 5.885,2.948 6.167,3.094 0.281,0.146 10 false G55 6.229,2.948 6.458,3.104 0.229,0.156 10 false DI 5.938,3.906 6.146,4.052 0.208,0.146 10 false 36 5.875,4.125 6.156,4.271 0.281,0.146 10 false G56 6.229,4.135 6.656,4.292 0.427,0.156 10 false MREL 6.396,5.49 6.75,5.656 0.354,0.167 10 false ECM 4.042,1.781 4.271,1.938 0.229,0.156 10 false +B 4.75,1.771 5.052,1.927 0.302,0.156 10 false FPC 4.042,2.948 4.177,3.104 0.135,0.156 10 false E 4.885,2.948 5.063,3.104 0.177,0.156 10 false DI 4.083,3.417 4.313,3.573 0.229,0.156 10 false FP 4.792,3.417 5.052,3.573 0.26,0.156 10 false FP-

for Manual Transmission

A353963E01
1.177,0.646 1.469,0.802 0.292,0.156 10 false IGN 0.365,1.958 0.49,2.115 0.125,0.156 10 false 5 0.563,1.958 0.771,2.125 0.208,0.167 10 false 1A 0.365,3.75 0.49,3.906 0.125,0.156 10 false 1 1.354,1.958 1.479,2.115 0.125,0.156 10 false 3 1.354,3.75 1.479,3.906 0.125,0.156 10 false 1 0.563,3.75 0.771,3.917 0.208,0.167 10 false 1C 1.052,1.958 1.26,2.125 0.208,0.167 10 false 1A 1.052,3.74 1.26,3.906 0.208,0.167 10 false 1A 2.271,3.75 2.396,3.906 0.125,0.156 10 false 2 2.458,3.75 2.667,3.917 0.208,0.167 10 false 1B 2.458,1.958 2.667,2.125 0.208,0.167 10 false 1B 1.844,1.958 1.969,2.115 0.125,0.156 10 false 4 2.75,1.958 2.875,2.115 0.125,0.156 10 false 3 2.031,1.958 2.24,2.125 0.208,0.167 10 false 1B 1.344,3.938 2.448,4.26 1.104,0.323 10 false No. 1 Integration Relay 1.406,2.427 1.667,2.573 0.26,0.146 10 false IG2 0.74,3.083 1,3.229 0.26,0.146 10 false IG2 2.208,3.052 2.469,3.208 0.26,0.156 10 false EFI 2.802,2.427 3.073,2.583 0.271,0.156 10 false EFI 0.229,6.125 0.563,6.271 0.333,0.146 10 false P/I-B 0.885,6.875 1.365,7.063 0.479,0.188 10 false Battery 2.385,5.979 2.76,6.135 0.375,0.156 10 false IG2D 2.573,5.729 2.688,5.885 0.115,0.156 10 false 8 2.271,6.521 2.583,6.667 0.313,0.146 10 false G50 2.271,6.656 4.51,6.823 2.24,0.167 10 false Power Management Control ECU 2.573,0.365 2.677,0.521 0.104,0.156 10 false 2 3.344,0.365 3.448,0.521 0.104,0.156 10 false 1 2.573,0.823 2.677,0.979 0.104,0.156 10 false 5 3.344,0.823 3.448,0.979 0.104,0.156 10 false 3 2.76,1.323 3.24,1.49 0.479,0.167 10 false C/OPN 4,0.625 5.042,0.771 1.042,0.146 10 false Fuel Pump ECU 3.802,1.552 3.917,1.708 0.115,0.156 10 false 4 3.74,1.781 3.969,1.927 0.229,0.146 10 false S8 3.802,2.719 3.917,2.875 0.115,0.156 10 false 3 3.885,3.625 4,3.781 0.115,0.156 10 false 1 3.75,2.948 3.979,3.094 0.229,0.146 10 false S8 4.073,3.635 4.302,3.781 0.229,0.146 10 false S9 4.635,3.625 4.75,3.781 0.115,0.156 10 false 2 4.813,3.635 5.042,3.781 0.229,0.146 10 false S9 5.177,1.552 5.292,1.708 0.115,0.156 10 false 1 5.135,1.781 5.365,1.927 0.229,0.146 10 false S8 5.177,2.719 5.292,2.875 0.115,0.156 10 false 2 5.125,2.948 5.354,3.094 0.229,0.146 10 false S8 4.052,4.521 4.167,4.667 0.115,0.146 10 false 4 4.948,4.521 5.063,4.667 0.115,0.146 10 false 5 4.198,4.792 4.417,4.948 0.219,0.156 10 false B2 4.698,4.792 4.917,4.948 0.219,0.156 10 false E2 4.198,5.333 4.427,5.479 0.229,0.146 10 false S5 4.198,5.469 4.906,5.656 0.708,0.188 10 false Fuel Pump 5.979,0.302 6.104,0.448 0.125,0.146 10 false 8 5.875,0.521 6.156,0.667 0.281,0.146 10 false G56 6.229,0.479 6.458,0.635 0.229,0.156 10 false FC 5.979,1.552 6.104,1.698 0.125,0.146 10 false 3 5.875,1.771 6.156,1.917 0.281,0.146 10 false G55 6.229,1.729 6.542,1.885 0.313,0.156 10 false FPC 5.948,2.729 6.135,2.875 0.188,0.146 10 false 26 5.896,2.948 6.177,3.094 0.281,0.146 10 false G56 6.229,2.906 6.458,3.063 0.229,0.156 10 false DI 5.979,3.906 6.104,4.052 0.125,0.146 10 false 9 5.896,4.115 6.177,4.26 0.281,0.146 10 false G55 6.229,4.083 6.656,4.24 0.427,0.156 10 false MREL 6.396,5.521 6.75,5.688 0.354,0.167 10 false ECM 4.042,1.74 4.271,1.896 0.229,0.156 10 false +B 4.75,1.74 5.052,1.896 0.302,0.156 10 false FPC 4.042,2.906 4.177,3.063 0.135,0.156 10 false E 4.885,2.906 5.063,3.063 0.177,0.156 10 false DI 4.083,3.417 4.313,3.573 0.229,0.156 10 false FP 4.792,3.417 5.052,3.573 0.26,0.156 10 false FP-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Enter the following menus: Body Electrical / Combination Meter / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC B1500 is not output A
DTC B1500 is output B



A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the fuel pump / Speed.


d.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.

OK:

Operating sounds can be heard from fuel pump.




OK

NG

3.INSPECT CIRCUIT OPENING RELAY (C/OPN)
3.INSPECT CIRCUIT OPENING RELAY (C/OPN)
a.

Inspect the circuit opening relay (C/OPN) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

4.INSPECT CIRCUIT OPENING RELAY (C/OPN) (POWER SOURCE VOLTAGE)

NG

REPLACE CIRCUIT OPENING RELAY (C/OPN)

4.INSPECT CIRCUIT OPENING RELAY (C/OPN) (POWER SOURCE VOLTAGE)
A227634E02
0.405,1.177 0.608,1.333 0.202,0.156 10 *1 2.262,0.209 2.464,0.365 0.202,0.156 10 *2

a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C/OPN relay terminal 2 - Body ground Engine switch on (IG) 11 to 14 V
C/OPN relay terminal 5 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 Circuit Opening Relay (C/OPN)


c.

Reinstall the circuit opening relay (C/OPN).



OK

5.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM, FUEL PUMP ECU)

NG

11.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - NO. 1 INTEGRATION RELAY)
5.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM, FUEL PUMP ECU)
a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Disconnect the fuel pump ECU connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C/OPN relay terminal 1 - G55-5(FC) Always Below 1 Ω
C/OPN relay terminal 3 - S8-4 (+B) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C/OPN relay terminal 1 - G56-8(FC) Always Below 1 Ω
C/OPN relay terminal 3 - S8-4 (+B) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C/OPN relay terminal 1 or G55-5 (FC) - Body ground Always 10 kΩ or higher
C/OPN relay terminal 3 or S8-4 (+B) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C/OPN relay terminal 1 or G56-8 (FC) - Body ground Always 10 kΩ or higher
C/OPN relay terminal 3 or S8-4 (+B) - Body ground Always 10 kΩ or higher



e.

Reinstall the circuit opening relay (C/OPN).


f.

Reconnect the fuel pump ECU connector.


g.

Reconnect the ECM connector.



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
a.

Disconnect the fuel sender gauge connector.


b.

Disconnect the fuel pump ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
S5-4 (B2) - S9-1 (FP) Always Below 1 Ω
S5-5 (E2) - S9-2 (FP-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
S5-4 (B2) or S9-1 (FP) - Body ground Always 10 kΩ or higher
S5-5 (E2) or S9-2 (FP-) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel sender gauge connector.


e.

Reconnect the fuel pump ECU connector.



OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL PUMP
a.

Inspect the fuel pump (for Single Tank Type) (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP (for Single Tank Type)>INSPECTION).


b.

Inspect the fuel pump (for Double Tank Type) (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP (for Double Tank Type)>INSPECTION).

Result
Test Result Proceed to
OK A
NG (for Single Tank Type) B
NG (for Double Tank Type) C

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

8.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)

B

C

8.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
S8-1 (FPC) - G55-4 (FPC) Always Below 1 Ω
S8-2 (DI) - G55-14 (DI) Always Below 1 Ω
S8-3 (E) - Body ground Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
S8-1 (FPC) - G55-3 (FPC) Always Below 1 Ω
S8-2 (DI) - G56-26 (DI) Always Below 1 Ω
S8-3 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
S8-1 (FPC) or G55-4 (FPC) - Body ground Always 10 kΩ or higher
S8-2 (DI) or G55-14 (DI) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
S8-1 (FPC) or G55-3 (FPC) - Body ground Always 10 kΩ or higher
S8-2 (DI) or G56-26 (DI) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel pump ECU connector.


e.

Reconnect the ECM connector.



OK

9.REPLACE FUEL PUMP ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE FUEL PUMP ECU
a.

Replace the fuel pump ECU (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP ECU>REMOVAL).



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS
10.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Start the engine and idle it for 5 minutes.


f.

Drive the vehicle in an urban area for approximately 10 minutes.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
No output A
DTC P0230 is output B



A

END

B

11.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - NO. 1 INTEGRATION RELAY)
a.

Remove the circuit opening relay (C/OPN) from the engine room relay block.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C/OPN relay terminal 2 - 1A-5 Always Below 1 Ω
C/OPN relay terminal 5 - 1B-4 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C/OPN relay terminal 2 or 1A-5 - Body ground Always 10 kΩ or more
C/OPN relay terminal 5 or 1B-4 - Body ground Always 10 kΩ or more



d.

Reinstall the circuit opening relay (C/OPN).


e.

Reinstall the No. 1 integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR