Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0171  System Too Lean (Bank 1)  P0172  System Too Rich (Bank 1)  P0174  System Too Lean (Bank 2)  P0175  System Too Rich (Bank 2)  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trim.

The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if it is lean.

Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

If both the short-term and long-term fuel trim are lean or rich beyond predetermined values, it is interpreted as a malfunction, and the ECM illuminates the MIL and stores a DTC.

DTC No. DTC Detection Condition Trouble Area
P0171
P0174
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic).
·

Air induction system

·

Fuel injector assembly blockage

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leakage from exhaust system

·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Air fuel ratio sensor heater (bank 1, 2 sensor 1)

·

No. 1 integration relay (A/F)

·

Air fuel ratio sensor heater circuits

·

PCV valve and hose

·

PCV hose connections

·

ECM


P0172
P0175
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic).
·

Injector leakage or blockage

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leakage from exhaust system

·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Air fuel ratio sensor heater (bank 1, 2 sensor 1)

·

No. 1 integration relay (A/F)

·

Air fuel ratio sensor heater circuits

·

ECM



HINT:
·

When DTC P0171 or P0174 is stored, the actual air fuel ratio is on the lean side. When DTC P0172 or P0175 is stored, the actual air fuel ratio is on the rich side.

·

If the vehicle runs out of fuel, the air fuel ratio becomes lean and DTC P0171 or P0174 may be stored. The MIL is then illuminated.

·

When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is higher than 75°C [167°F]), the system is functioning normally.



MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores a DTC.

Example:

If the average fuel trim learned value is more than +35% or less than -35%, the ECM interprets this as a fuel system malfunction.

A121607E01
2.661,1.905 2.306,1.905 false 2.659,3.035 2.307,3.035 false 1.667,0.576 2.916,0.922 1.249,0.346 10 Fuel Compensation Amount 0.069,1.556 1.467,2.090 1.398,0.535 10 +35%: Malfunction Threshold of LEAN Condition 0.069,2.995 1.487,3.540 1.418,0.545 10 -35%: Malfunction Threshold of RICH Condition 1.896,1.821 2.200,1.982 0.304,0.160 10 1.35 1.896,2.382 2.138,2.584 0.242,0.202 10 1.0 1.896,2.943 2.219,3.145 0.323,0.202 10 0.65 0.069,1.194 1.004,1.341 0.935,0.147 10 P0171, P0174 0.069,2.661 0.988,2.812 0.919,0.152 10 P0172, P0175 1.521,3.157 1.839,3.036 false 1.54,1.914 1.864,1.914 false

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for air fuel ratio sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

5.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

6.

Monitor the output voltages of the air fuel ratio sensor and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2, or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E50
5.792,3.594 7.115,3.865 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.469,1.604 1.917,1.792 0.448,0.188 8 false +12.5% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.813,0.448 2.844,0.844 2.031,0.396 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.375,0.469 5.531,0.875 2.156,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4 7.125,4.438 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - Heated oxygen sensor 5.844,6.135 6.885,6.563 1.042,0.427 10 false - Heated oxygen sensor heater 5.844,6.75 6.885,7.188 1.042,0.438 10 false - Heated oxygen sensor circuit 5.823,7.51 6.708,7.917 0.885,0.406 10 false - Fuel injector assembly 5.813,8.063 6.969,8.396 1.156,0.333 10 false - Fuel pressure 5.802,8.375 7.094,9.083 1.292,0.708 10 false - Gas leakage from exhaust system (air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.417,3.677 1.865,3.865 0.448,0.188 8 false +12.5% 4.01,1.594 4.458,1.781 0.448,0.188 8 false +12.5% 4,3.667 4.448,3.854 0.448,0.188 8 false +12.5% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.406,5.75 1.854,5.938 0.448,0.188 8 false +12.5% 1.375,7.771 1.823,7.958 0.448,0.188 8 false +12.5% 4.031,7.792 4.479,7.979 0.448,0.188 8 false +12.5% 4.073,5.729 4.521,5.917 0.448,0.188 8 false +12.5% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0171, P0172, P0174 or P0175 A
P0171, P0172, P0174 or P0175 and other DTCs B

HINT:

If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

OK:

PCV hose is connected correctly and is not damaged.




OK

3.CHECK AIR INDUCTION SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK AIR INDUCTION SYSTEM
HINT:

If a malfunction occurs when depressing the brake pedal, inspect the brake booster assembly, as there may be a vacuum leak in the brake booster assembly itself


a.

Check the air induction system for vacuum leakage.

OK:

No leakage in air induction system.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

4.PERFORM ACTIVE TEST USING GTS (AIR FUEL RATIO CONTROL)

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

4.PERFORM ACTIVE TEST USING GTS (AIR FUEL RATIO CONTROL)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


e.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).


f.

Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2, or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V


Result
Status of
AFS Voltage B1S1
or
AFS Voltage B2S1
Status of
O2S B1S2
or
O2S B2S2
Air fuel ratio Condition and
Air fuel ratio Sensor Condition
Misfire Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - - C
Lean Lean Actual air fuel ratio lean May occur
·

PCV valve and hose

·

PCV hose connections

·

Fuel injector assembly blockage

·

Gas leakage from exhaust system

·

Air induction system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


A
Rich Rich Actual air fuel ratio rich -
·

Fuel injector assembly leakage blockage or blockage

·

Gas leakage from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor



Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the AFS is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.



A

5.READ VALUE USING GTS (COOLANT TEMP)

B

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

C

15.PERFORM CONFIRMATION DRIVING PATTERN
5.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


d.

Read the Data List twice, when the engine is cold and when it is warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: 80 to 100°C (176 to 212°F).


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

6.INSPECT MASS AIR FLOW METER

NG

6.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter subassembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

7.CHECK FUEL PRESSURE

NG

7.CHECK FUEL PRESSURE

OK

8.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE FUEL SYSTEM

8.CHECK FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leakage from the exhaust manifold sub-assembly and exhaust pipes.

OK:

No gas leakage.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

9.CHECK SPARK AND IGNITION

NG

REPAIR OR REPLACE EXHAUST SYSTEM

9.CHECK SPARK AND IGNITION
a.

Check the ignition system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the spark plugs or ignition system malfunctions, engine misfires may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Rate (to Cylinder #6 Misfire Count).


for Automatic Transmission
·

Perform "Inspection After Repair" after repairing or replacing the ignition system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).





OK

10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE IGNITION SYSTEM

10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Inspect the fuel injector assembly (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>INSPECTION).

HINT:
·

If the injectors malfunction, engine misfires may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Rate (to Cylinder #6 Misfire Count).


for Automatic Transmission
·

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).





OK

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

12.INSPECT NO. 1 INTEGRATION RELAY (A/F)

NG

12.INSPECT NO. 1 INTEGRATION RELAY (A/F)
a.

Inspect the No. 1 integration relay (A/F) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (A/F)

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C37-17 (HA1A) Always Below 1 Ω
C26-1 (HA2A) - C37-12 (HA2A) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C37-17 (HA1A) Always Below 1 Ω
C26-1 (HA2A) - C37-19 (HA2A) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) or C37-17 (HA1A) - Body ground Always 10 kΩ or higher
C26-1 (HA2A) or C37-12 (HA2A) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) or C37-17 (HA1A) - Body ground Always 10 kΩ or higher
C26-1 (HA2A) or C37-19 (HA2A) - Body ground Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reconnect the ECM connector.



OK

14.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

15.PERFORM CONFIRMATION DRIVING PATTERN
15.PERFORM CONFIRMATION DRIVING PATTERN
A162663E41
1.635,2.385 1.385,2.229 false 1.906,2.594 1.479,2.927 false 0.698,0.188 1.688,0.365 0.99,0.177 10 false Vehicle Speed 0.042,0.75 1.708,1.104 1.667,0.354 10 false Between 60 and 120 km/h (38 and 75 mph) 1,2.115 1.438,2.313 0.438,0.198 10 false Idling 0.521,2.479 1.75,2.656 1.229,0.177 10 false Engine Switch Off 0.927,2.948 1.875,3.135 0.948,0.188 10 false (a), (b), (c), (d) 2.063,2.906 2.854,3.094 0.792,0.188 10 false Warming up 3.365,2.927 4.313,3.115 0.948,0.188 10 false 3 to 5 minutes 4.875,2.792 5.25,2.979 0.375,0.188 10 false Time 2.385,2.188 2.594,2.365 0.208,0.177 10 false (e) 3.917,0.771 4.125,0.948 0.208,0.177 10 false (f)

a.

Connect the GTS to the DLC3 (step "a").


b.

Turn the engine switch on (IG) and turn the GTS on (step "b").



d.

Switch the ECM from normal mode to check mode using the GTS (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE) (step "d").


e.

Start the engine and warm it up with all the accessories switched off (step "e").


f.

Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 3 to 5 minutes (step "f").

HINT:

If the system is still malfunctioning, the MIL is illuminated during this step.


NOTICE:

If the conditions in this test are not strictly followed, no malfunction will be detected.




NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
No output A
P0171, P0172, P0174 or P0175 B



A

END

B