Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM J

1KD-FTV ENGINE CONTROL  ECD SYSTEM  Pre-heating Control Circuit  


DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates the period of time that the current needs to flow through the glow plug depending on the starting engine coolant temperature when the ignition switch is turned to ON. The ECM then turns on the glow plug relay and permits the current to flow through the glow plug based on the time calculated by the ECM. The glow plug is then heated, and enhances fuel combustion with a cold engine.

A129368E17
0.042,0.031 2.427,0.24 2.385,0.208 10 false Glow System Wiring Diagram 0.521,0.427 1.104,0.823 0.583,0.396 10 false from Battery 1.656,0.354 2.219,0.552 0.563,0.198 10 false GLOW 1.167,1.958 1.958,2.156 0.792,0.198 10 false Glow Plug 5.906,0.083 6.333,0.281 0.427,0.198 10 false ECM 5.219,0.521 5.719,0.729 0.5,0.208 10 false GREL 3.25,1.104 3.813,1.302 0.563,0.198 10 false GLOW

HINT:
·

These troubleshooting procedures are for: 1) difficulty starting the engine in cold weather, and 2) difficulty driving/vehicle malfunctions in cold weather immediately after the engine is started.

·

After the engine is started, the ECM performs "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.



A117830E13
0.125,0.021 1.406,0.229 1.281,0.208 10 false After-glow System 1.667,0.948 2.719,1.146 1.052,0.198 10 false After-glow Time 2.542,0.219 3.229,0.406 0.688,0.188 10 false (Seconds) 2.948,1.906 4.76,2.115 1.813,0.208 10 false Engine Coolant Temperature 2.438,2.688 2.76,2.885 0.323,0.198 10 false Off 2.438,3.271 2.75,3.469 0.313,0.198 10 false Off 4.042,2.385 4.292,2.583 0.25,0.198 10 false On 4.042,2.99 4.292,3.188 0.25,0.198 10 false On 1.302,2.844 2.25,3.021 0.948,0.177 10 false Ignition Switch 1.583,3.438 2.26,3.656 0.677,0.219 10 false Glow Plug 1.344,4.042 2.25,4.25 0.906,0.208 10 false Engine Speed 2.823,4.406 3.635,4.625 0.813,0.219 10 false Engine Start 3.74,4.292 4.896,4.5 1.156,0.208 10 false After-glow Time 5.031,3.271 5.406,3.469 0.375,0.198 10 false Off

WIRING DIAGRAM

A227729E03
3.073,2.698 3.813,2.927 0.74,0.229 10 false Glow Plug 1.667,1.677 2.208,1.854 0.542,0.177 10 false GLOW 1.115,2.75 1.677,3.042 0.563,0.292 10 false Battery 6.063,3.479 6.417,3.625 0.354,0.146 10 false ECM 5.865,0.531 6.313,0.708 0.448,0.177 10 false GREL 6.063,3.302 6.354,3.479 0.292,0.177 10 false C91 3.073,2.531 3.365,2.708 0.292,0.177 10 false C98 5.573,0.417 5.781,0.604 0.208,0.188 10 false 19 3.76,1.021 3.917,1.24 0.156,0.219 10 false 1 3.021,1 3.24,1.198 0.219,0.198 10 false 2 3.76,1.406 3.948,1.656 0.188,0.25 10 false 3 3.021,1.406 3.26,1.698 0.24,0.292 10 false 5 4.26,2.177 4.469,2.396 0.208,0.219 10 false 1 3.208,1.844 3.688,2.021 0.479,0.177 10 false GLOW

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK TERMINAL VOLTAGE (GLOW PLUG RELAY(GLOW))
a.
A227730E01
0.549,1.437 0.783,1.607 0.235,0.170 10 *1 2.548,0.572 2.740,0.751 0.192,0.179 10 *2

Remove the glow plug relay (GLOW).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Glow plug relay terminal-5 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 Glow Plug Relay (GLOW)


c.

Reinstall the glow plug relay (GLOW).



OK

2.INSPECT GLOW PLUG RELAY(GLOW)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR (GLOW PLUG RELAY - BATTERY)

2.INSPECT GLOW PLUG RELAY(GLOW)
a.

Inspect the glow plug relay (GLOW) (See page Engine / Hybrid System>1KD-FTV (STARTING)>RELAY>ON-VEHICLE INSPECTION).



OK

3.INSPECT GLOW PLUG (RESISTANCE)

NG

REPLACE GLOW PLUG RELAY

3.INSPECT GLOW PLUG (RESISTANCE)

OK

4.CHECK GLOW PLUG (INSTALLATION)

NG

4.CHECK GLOW PLUG (INSTALLATION)
a.

Check the glow plug installation.

OK:

Glow plugs are installed securely.



Torque:
12.3 N*m (125 kgf*cm, 9 ft.*lbf)


OK

5.CHECK WIRE HARNESS (GLOW PLUG - GLOW PLUG RELAY(GLOW) - BODY GROUND)

NG

TIGHTEN GLOW PLUG

5.CHECK WIRE HARNESS (GLOW PLUG - GLOW PLUG RELAY(GLOW) - BODY GROUND)
a.

Remove the glow plug relay (GLOW).


b.

Disconnect the glow plug connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Glow plug relay terminal-3 - C98-1 Always Below 1 Ω
Glow plug relay terminal-1 - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Glow plug relay terminal-3 or C98-1 - Body ground Always 10 kΩ or higher



d.

Reinstall the glow plug relay (GLOW).


e.

Reconnect the glow plug connector.



OK

6.CHECK WIRE HARNESS (GLOW PLUG RELAY(GLOW) - ECM AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (GLOW PLUG RELAY(GLOW) - ECM AND BODY GROUND)
a.

Remove the glow plug relay (GLOW).


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Glow plug relay terminal-2 - C91-19 (GREL) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Glow plug relay terminal-2 or C91-19 (GREL) - Body ground Always 10 kΩ or higher



d.

Reinstall the glow plug relay (GLOW).


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR