Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0200  Injector Circuit / Open  


DESCRIPTION

The injector driver delivers drive signals to the injector assemblies using the DC/DC converter, which provides a high-voltage and quick-charging system.

Soon after the injector driver receives a fuel injection command (#1 to #4) signal from the ECM, the injector driver responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector assembly.

U169187E02
3.271,0.063 4.188,0.229 0.917,0.167 10 false Injector Driver 2.615,1.146 3.281,1.542 0.667,0.396 10 false DC/DC Converter 0.448,1.313 1.271,1.552 0.823,0.24 10 false from Battery 0.281,2.167 1.375,2.344 1.094,0.177 10 false Command Pulse 0.854,4.615 2.146,4.792 1.292,0.177 10 false Confirmation Pulse 0.115,5.677 1.781,5.854 1.667,0.177 10 false Injector Driver Connector 0.115,0.073 2.146,0.25 2.031,0.177 10 false Injector Driver Wiring Diagram 0.677,3.333 1.073,3.552 0.396,0.219 10 false ECM 1.542,2.5 1.917,2.667 0.375,0.167 10 false #1 1.552,2.781 1.885,2.948 0.333,0.167 10 false #4 1.552,3.094 1.885,3.26 0.333,0.167 10 false #2 1.552,3.396 1.906,3.563 0.354,0.167 10 false #3 1.49,4.01 1.875,4.177 0.385,0.167 10 false INJF 1.49,3.698 1.813,3.865 0.323,0.167 10 false PRD 5.073,2.469 5.594,2.635 0.521,0.167 10 false IJ1- 5.073,0.594 5.5,0.76 0.427,0.167 10 false RLF+ 5.073,0.896 5.594,1.063 0.521,0.167 10 false IJ3+ 5.073,1.229 5.615,1.396 0.542,0.167 10 false IJ2+ 5.073,1.542 5.552,1.708 0.479,0.167 10 false IJ4+ 5.063,1.854 5.646,2.021 0.583,0.167 10 false IJ1+ 5.073,2.792 5.594,2.958 0.521,0.167 10 false IJ4- 5.073,3.104 5.563,3.271 0.49,0.167 10 false IJ2- 5.073,3.427 5.573,3.594 0.5,0.167 10 false IJ3- 5.052,3.74 5.573,3.906 0.521,0.167 10 false RLF- 3.229,3.01 3.698,3.344 0.469,0.333 10 false Control Circuit 3.615,5.417 3.958,5.583 0.344,0.167 10 false GND 0.99,7.385 5.927,7.625 4.938,0.24 10 false CAUTION: Terminals H, I, J, K, L, M, N, O, S and T are high-voltage terminals. 2.125,5.865 2.427,6.01 0.302,0.146 10 false C88 4.448,5.865 4.75,6.01 0.302,0.146 10 false C89 3.354,5.865 3.635,6.01 0.281,0.146 10 false C99

P0200
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 5 seconds Open or short in the injector driver or fuel injector circuit (1 trip detection logic).
·

Open or short in injector driver circuit

·

Injector assembly

·

Injector driver

·

ECM



MONITOR DESCRIPTION

P0200 (Open or short in injector driver or fuel injector circuit):

The ECM continuously monitors both injection command (#1 to #4) signals and injection confirmation (INJF) signals. This DTC will be stored if the ECM determines that the number of #1 to #4 signals is inconsistent with the number of INJF signals.

The injector assemblies are grounded through a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (injector drive circuit) in relation to the current drawn by the injector assembly. When the injector assembly current becomes too high, the voltage drop over the resistor exceeds a specified level and no IJF signal for that cylinder is sent to the ECM.

After the engine is started, when there is no injection confirmation (INJF) signal sent from the injector driver to the ECM even though the ECM sends injection command (#1 to #4) signals to the injector driver, DTC P062D is stored.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

A145849E55
4.958,2.469 4.625,2.865 false 4.635,3.25 4.875,3.552 false 0.115,0.052 1.698,0.26 1.583,0.208 10 false Malfunction Detection: 2.625,0.688 3.031,0.885 0.406,0.198 10 false ECM 0.063,1.76 1.75,1.979 1.688,0.219 10 false Injection Command Signal 0.063,3.031 2.021,3.24 1.958,0.208 10 false Injection Confirmation Signal 1.833,2.021 2.438,2.229 0.604,0.208 10 false #1 to #4 2.063,2.781 2.417,2.99 0.354,0.208 10 false INJF 3.302,1.781 3.583,1.979 0.281,0.198 10 false ON 3.552,0.479 5.344,0.719 1.792,0.24 10 false Command Signal (#1 to #4) 3.573,1.063 5.26,1.26 1.688,0.198 10 false Confirmation Signal (INJF) 5.906,0.677 6.375,0.885 0.469,0.208 10 false EDU 3.708,2.146 4.073,2.344 0.365,0.198 10 false OFF 5.021,2.375 5.792,2.573 0.771,0.198 10 false Abnormal 4.917,3.49 5.5,3.688 0.583,0.198 10 false Normal


WIRING DIAGRAM

A205139E09
0.632,0.783 0.973,0.952 0.341,0.170 10 INJF 1.033,0.799 1.334,0.958 0.302,0.159 10 C89 1.037,1.234 1.366,1.393 0.329,0.159 10 C89 1.031,1.675 1.332,1.834 0.302,0.159 10 C89 1.035,2.107 1.336,2.266 0.302,0.159 10 C89 1.035,2.551 1.336,2.710 0.302,0.159 10 C89 1.035,3.048 1.336,3.207 0.302,0.159 10 C88 1.035,3.976 1.336,4.135 0.302,0.159 10 C99 1.124,0.612 1.241,0.772 0.117,0.159 10 5 0.68,1.219 0.973,1.389 0.293,0.170 10 #10 1.134,1.049 1.295,1.208 0.161,0.159 10 4 0.68,2.561 0.973,2.730 0.293,0.170 10 #40 1.124,1.494 1.241,1.653 0.117,0.159 10 8 0.68,1.696 0.973,1.866 0.293,0.170 10 #20 1.124,1.927 1.241,2.086 0.117,0.159 10 7 0.661,2.12 0.955,2.290 0.293,0.170 10 #30 6.222,0.783 6.563,0.952 0.341,0.170 10 INJF 6.222,1.219 6.516,1.389 0.293,0.170 10 #1 6.241,2.526 6.534,2.695 0.293,0.170 10 #4 6.222,2.097 6.516,2.267 0.293,0.170 10 #3 6.222,1.678 6.516,1.847 0.293,0.170 10 #2 5.87,0.805 6.152,0.964 0.282,0.159 10 C90 5.906,0.611 6.096,0.770 0.190,0.159 10 20 5.874,1.236 6.156,1.395 0.282,0.159 10 C90 5.898,1.052 6.098,1.211 0.199,0.159 10 21 5.866,1.677 6.148,1.837 0.282,0.159 10 C90 5.91,1.493 6.128,1.652 0.218,0.159 10 22 5.876,2.112 6.158,2.271 0.282,0.159 10 C90 5.91,1.927 6.128,2.087 0.218,0.159 10 23 5.868,2.552 6.150,2.712 0.282,0.159 10 C90 5.91,2.372 6.109,2.532 0.199,0.159 10 24 1.124,2.37 1.241,2.530 0.117,0.159 10 3 0.652,3.036 0.949,3.206 0.297,0.170 10 IJ1+ 1.124,2.867 1.241,3.026 0.117,0.159 10 1 4.264,3.154 4.381,3.313 0.117,0.159 10 2 3.591,3.136 3.708,3.295 0.117,0.159 10 1 1.124,4.209 1.241,4.368 0.117,0.159 10 6 1.106,6.61 1.223,6.769 0.117,0.159 10 2 1.124,5.715 1.241,5.874 0.117,0.159 10 5 1.124,3.804 1.241,3.964 0.117,0.159 10 6 1.122,5.113 1.239,5.273 0.117,0.159 10 4 3.44,3.348 3.811,3.524 0.371,0.177 10 C1 3.44,3.494 5.037,3.656 1.598,0.162 10 No. 1 Injector Assembly 3.44,4.692 3.769,4.869 0.329,0.177 10 C2 3.44,7.706 5.037,7.868 1.598,0.162 10 No. 4 Injector Assembly 3.44,6.157 3.769,6.333 0.329,0.177 10 C3 3.43,4.846 4.916,5.008 1.486,0.162 10 No. 2 Injector Assembly 3.44,7.537 3.769,7.713 0.329,0.177 10 C4 3.459,6.307 4.959,6.469 1.500,0.162 10 No. 3 Injector Assembly 4.3,4.483 4.418,4.642 0.117,0.159 10 2 3.61,4.481 3.727,4.640 0.117,0.159 10 1 4.273,5.989 4.390,6.148 0.117,0.159 10 2 3.58,5.98 3.697,6.139 0.117,0.159 10 1 4.276,7.327 4.393,7.486 0.117,0.159 10 2 3.61,7.327 3.727,7.486 0.117,0.159 10 1 0.672,3.992 0.941,4.162 0.269,0.170 10 IJ1- 1.031,4.412 1.333,4.571 0.302,0.159 10 C88 1.035,5.316 1.336,5.475 0.302,0.159 10 C99 1.025,5.886 1.326,6.046 0.302,0.159 10 C88 0.649,4.409 0.946,4.579 0.297,0.170 10 IJ2+ 0.649,5.306 0.918,5.475 0.269,0.170 10 IJ2- 0.675,5.891 0.972,6.060 0.297,0.170 10 IJ3+ 0.687,6.787 0.956,6.957 0.269,0.170 10 IJ3- 1.028,7.24 1.329,7.399 0.302,0.159 10 C99 1.031,8.154 1.332,8.313 0.302,0.159 10 C99 1.027,6.809 1.328,6.968 0.302,0.159 10 C99 1.121,7.042 1.242,7.198 0.121,0.156 10 3 1.1,7.952 1.219,8.108 0.119,0.156 10 5 0.656,7.235 0.953,7.405 0.297,0.170 10 IJ4+ 0.668,8.132 0.937,8.301 0.269,0.170 10 IJ4- 6.353,0.191 6.689,0.360 0.336,0.170 10 ECM 0.187,0.121 1.127,0.270 0.941,0.149 10 Injector Driver

A227726E36
6.458,5.271 6.813,5.448 0.354,0.177 10 false ECM 4.396,1.656 4.75,1.833 0.354,0.177 10 false EDU 4.396,3.354 4.688,3.542 0.292,0.188 10 false EFI 0.229,5.271 1.125,5.448 0.896,0.177 10 false Injector Driver 1.49,4.615 2.031,4.802 0.542,0.188 10 false Battery 1.625,3.729 2.042,3.917 0.417,0.188 10 false P/I-B 2.885,3.729 3.177,3.917 0.292,0.188 10 false EFI 4.052,1.042 4.25,1.219 0.198,0.177 10 false 1B 3.49,1.031 3.688,1.208 0.198,0.177 10 false 1B 3.281,1.042 3.448,1.24 0.167,0.198 10 false 8 4.344,1.042 4.51,1.24 0.167,0.198 10 false 7 5.063,2.458 5.26,2.635 0.198,0.177 10 false 1B 5.063,2.875 5.26,3.052 0.198,0.177 10 false 1B 5.073,3.906 5.271,4.083 0.198,0.177 10 false 1B 4.042,4.125 4.24,4.302 0.198,0.177 10 false 1B 2.365,3.906 2.604,4.083 0.24,0.177 10 false 1C 2.271,4.344 4.021,4.708 1.75,0.365 10 false No. 1 Integration Relay (Engine Room Relay Block) 0.99,1.542 1.354,1.719 0.365,0.177 10 false C88 0.99,0.563 1.354,0.74 0.365,0.177 10 false C88 6.01,0.563 6.333,0.74 0.323,0.177 10 false G58 6.01,2.875 6.333,3.052 0.323,0.177 10 false G58 6.021,3.906 6.344,4.083 0.323,0.177 10 false G57 6.01,2.458 6.333,2.635 0.323,0.177 10 false G57 5.125,2.271 5.281,2.448 0.156,0.177 10 false 4 5.115,2.698 5.271,2.875 0.156,0.177 10 false 2 5.115,3.719 5.271,3.896 0.156,0.177 10 false 1 6.063,3.719 6.302,3.917 0.24,0.198 10 false 23 6.052,2.698 6.292,2.896 0.24,0.198 10 false 11 6.063,2.271 6.302,2.469 0.24,0.198 10 false 24 6.052,0.375 6.292,0.573 0.24,0.198 10 false 12 1.052,0.354 1.208,0.531 0.156,0.177 10 false 2 2.406,3.719 2.563,3.896 0.156,0.177 10 false 1 4.323,4.125 4.479,4.302 0.156,0.177 10 false 3 1.052,1.333 1.208,1.51 0.156,0.177 10 false 3 6.354,2.448 6.615,2.604 0.26,0.156 10 false +B 0.708,0.563 0.969,0.719 0.26,0.156 10 false +B 0.583,1.542 0.958,1.698 0.375,0.156 10 false GND 6.354,0.563 6.729,0.74 0.375,0.177 10 false IREL 6.354,2.875 6.844,3.063 0.49,0.188 10 false MREL 6.354,3.906 6.813,4.073 0.458,0.167 10 false BATT

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:
·

When DTC P0200 is stored, the malfunctioning parts can be narrowed down according to fail-safe behavior.

-

When a DTC is stored but the engine does not stall, there may be an open circuit or malfunction in the following components which affect the control of individual cylinders.

(1)

The circuit inside an injector assembly.

(2)

The wiring between an injector driver and injector assembly (between terminal IJ1+ and the No. 1 injector assembly, terminal IJ1 and the No. 1 injector assembly, etc.).

(3)

The wiring between an injector driver and the ECM (terminals #10 and #1, etc.).


-

When a DTC is stored and the engine stalls, there may be a malfunction in the wiring which affects the control of multiple cylinders.

(1)

Wiring between an injector driver and the ECM (between INJF terminals).

(2)

The power supply wiring.



·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE
a.
U169188E01
0.546,1.307 0.827,1.459 0.281,0.152 10 C88 0.626,0.765 1.101,0.912 0.476,0.147 10 +B (+) 1.7,1.206 1.173,0.859 false 0.074,0.119 0.273,0.271 0.199,0.152 10 *a 2.456,1.662 3.024,1.809 0.568,0.147 10 GND (-) 2.443,1.647 1.989,1.258 false

Disconnect the injector driver connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C88-2 (+B) - C88-3 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to injector driver)


c.

Reconnect the injector driver connectors.



OK

2.INSPECT INJECTOR ASSEMBLY (RESISTANCE)

NG

8.GO TO INJECTOR CIRCUIT
2.INSPECT INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the injector assembly (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL INJECTOR>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)

NG

9.REPLACE INJECTOR ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)
a.

Disconnect the injector assembly connectors.


b.

Disconnect the injector driver connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C1-1 - C88-1 (IJ1+) Always Below 1 Ω
C1-2 - C99-6 (IJ1-) Always Below 1 Ω
C2-1 - C88-6 (IJ2+) Always Below 1 Ω
C2-2 - C88-4 (IJ2-) Always Below 1 Ω
C3-1 - C99-5 (IJ3+) Always Below 1 Ω
C3-2 - C99-2 (IJ3-) Always Below 1 Ω
C4-1 - C99-3 (IJ4+) Always Below 1 Ω
C4-2 - C99-5 (IJ4-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C1-1 or C88-1 (IJ1+) - Body ground Always 10 kΩ or higher
C1-2 or C99-6 (IJ1-) - Body ground Always 10 kΩ or higher
C2-1 or C88-6 (IJ2+) - Body ground Always 10 kΩ or higher
C2-2 or C99-4 (IJ2-) - Body ground Always 10 kΩ or higher
C3-1 or C88-5 (IJ3+) - Body ground Always 10 kΩ or higher
C3-2 or C99-2 (IJ3-) - Body ground Always 10 kΩ or higher
C4-1 or C99-3 (IJ4+) - Body ground Always 10 kΩ or higher
C4-2 or C99-5 (IJ4-) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector assembly connectors.


e.

Reconnect the injector driver connectors.



OK

4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
a.

Disconnect the injector driver connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C89-4 (#10) - C90-21 (#1) Always Below 1 Ω
C89-8 (#20) - C90-22 (#2) Always Below 1 Ω
C89-7 (#30) - C90-23 (#3) Always Below 1 Ω
C89-3 (#40) - C90-24 (#4) Always Below 1 Ω
C89-5 (INJF) - C90-20 (INJF) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C89-4 (#10) or C90-21 (#1) - Body ground Always 10 kΩ or higher
C89-8 (#20) or C90-22 (#2) - Body ground Always 10 kΩ or higher
C89-7 (#30) or C90-23 (#3) - Body ground Always 10 kΩ or higher
C89-3 (#40) or C90-24 (#4) - Body ground Always 10 kΩ or higher
C89-5 (INJF) or C90-20 (INJF) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver connector.


e.

Reconnect the ECM connector.



OK

5.REPLACE INJECTOR DRIVER

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE INJECTOR DRIVER
a.

Replace the injector driver (See page Engine / Hybrid System>1KD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and idle it for 10 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.


f.

Read the DTCs.

Result
Result Proceed to
P0200 is output A
No output B



A

7.REPLACE ECM

B

END

7.REPLACE ECM

NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.GO TO INJECTOR CIRCUIT

NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).



NEXT

10.BLEED AIR FROM FUEL SYSTEM
10.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

11.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
11.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


b.

Perform the injector pilot quantity learning (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and idle it for 10 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END