Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P2009  Intake Manifold Runner Control Circuit Low (Bank 1)  P2010  Intake Manifold Runner Control Circuit High (Bank 1)  


DESCRIPTION

Refer to DTC P2006 (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>P2006).

P2009
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Open in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
·

Vacuum switching valve (for swirl control valve)

·

Open in vacuum switching valve (for swirl control valve) circuit

·

ECM



P2010
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Short in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
·

Vacuum switching valve (for swirl control valve)

·

Short in vacuum switching valve (for swirl control valve) circuit

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
A067588E29
0.469,1.427 0.323,1.667 true 0.667,1.313 0.917,1.802 true 2,1.417 1.844,1.646 true 2.167,1.292 2.49,1.76 true 0.823,0.052 1.531,0.26 0.708,0.208 10 false VSV is ON 2.458,0.073 3.24,0.281 0.781,0.208 10 false VSV is OFF 0.552,0.313 0.771,0.51 0.219,0.198 10 false Air 2.333,1.771 2.813,1.969 0.479,0.198 10 false Port E 0.708,1.813 1.188,2.01 0.479,0.198 10 false Port E 1.625,1.656 2.094,1.854 0.469,0.198 10 false Port F 0.104,1.677 0.573,1.875 0.469,0.198 10 false Port F 2,0.385 2.219,0.583 0.219,0.198 10 false Air 2.76,0.552 3.333,0.75 0.573,0.198 10 false Air Filter

a.

Connect the intelligent tester to the DLC3.


b.

Disconnect the vacuum hoses from the vacuum switching valve (for Swirl Control Valve).


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.


e.

Check the VSV operation when it is operated using the intelligent tester.

OK:
Tester Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.



OK

NG

2.INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)
2.INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)
a.

Inspect the vacuum switching valve (for swirl control valve) (See page Engine / Hybrid System>1KD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSPECTION).



OK

3.INSPECT VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)

NG

8.REPLACE VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE)
3.INSPECT VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)
a.
U169098E02
0.167,0.125 0.448,0.333 0.281,0.208 10 false *a 0.792,1.385 1.198,1.552 0.406,0.167 10 false C143

Disconnect the vacuum switching valve (for swirl control valve) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
C143-2 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to vacuum switching valve (for swirl control valve))



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)
a.

Disconnect the vacuum switching valve (for swirl control valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C143-1 - C93-2 (SCV) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C143-1 or C93-2 (SCV) - Body ground Always 10 kΩ or higher



d.

Reconnect the vacuum switching valve (for swirl control valve) connector.


e.

Reconnect the ECM connector.



OK

5.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the No. 1 integration relay connector.


c.

Disconnect the vacuum switching valve (for swirl control valve) connector.


d.

Measure the resistance of the wire harness side connectors.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1B-4 - C143-2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1B-4 or C143-2 - Body ground Always 10 kΩ or higher



e.

Reinstall the No. 1 integration relay.


f.

Reconnect the No. 1 integration relay connector.


g.

Reconnect the vacuum switching valve (for swirl control valve) connector.



OK

7.INSPECT ECM POWER SOURCE CIRCUIT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.INSPECT ECM POWER SOURCE CIRCUIT

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE)
a.

Replace the vacuum switching valve (for swirl control valve) (See page Engine / Hybrid System>1KD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Confirm that the DTC is not output again.



NEXT

END