Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0093  Fuel System Leak Detected - Large Leak  


DESCRIPTION

The fuel pressure sensor mounted on the common rail converts the fuel pressure inside the common rail into an electrical signal and outputs the signal to the ECM. The ECM controls the supply pump in order to maintain the fuel pressure inside the common rail at a target pressure calculated by the ECM. Refer to System Description (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

HINT:
·

If the drop in the internal fuel pressure is large when injecting fuel, the ECM interprets this as a fault and stores P0093.

·

If P0093 is present, refer to "Diagnostic Trouble Code (DTC) Table for Common Rail System" (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).



P0093
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 60 seconds, run engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)
Repeat procedures (*A) and (*B) 5 times.
The fuel pressure decreases greatly when the engine is running.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Suction control valve

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (common rail assembly)

·

Crankshaft position sensor

·

Fuel filter element sub-assembly

·

Open or short in injector driver circuit (P0200 stored simultaneously)

·

Open or short in injector circuit

·

Injector driver (P0200 stored simultaneously)

·

ECM



Related Data List
DTC No. Data List
P0093
·

Fuel Press

·

Target Common Rail Pressure



HINT:

When DTC P0093 is set, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Fuel Press.


Reference:
Engine Speed Fuel Pressure
Idling Approximately 30000 to 40000 kPa
3000 rpm (No engine load) Approximately 45000 to 75000 kPa


MONITOR DESCRIPTION

P0093 (Fuel leaks in high-pressure areas):

This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when injecting fuel.

In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump assembly, common rail assembly, injector assemblies and piping. The ECM adjusts the suction control valve opening angle to obtain the target internal fuel pressure.

If this DTC is stored, the ECM enters fail-safe mode. In fail-safe mode, both fuel injection and fuel supply pump assembly operation are suspended, and then the engine is stopped. Before the engine is stopped, the ECM permits the vehicle to be driven for 1 minute. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


MONITOR STRATEGY

Required sensors Fuel pressure sensor
Frequency of operation Continuous
Duration 1 second
MIL operation 1 driving cycle

CAUTION / NOTICE / HINT

NOTICE:
·

Soon after starting the engine, visually check for fuel leaks in the fuel line.

·

After replacing the ECM, the new ECM needs registration (See Page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See Page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See Page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See Page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


A221570E20
0.76,5.656 6.99,5.802 6.229,0.146 0.76,4.219 6.99,4.365 6.229,0.146 4.708,1.583 5.469,6.365 0.76,4.781 2.125,6.677 2.688,4.354 false 4.969,6.677 5.042,6.365 false 0.094,0.021 5.042,0.188 4.948,0.167 10 false DTC P0093 stored due to a temporary stuck open malfunction of injector No. 3 0.917,6.708 3.198,7.115 2.281,0.406 10 false Injection Feedback Val #3 is stuck at the maximum value of 5.0 mm3/st 4.125,6.698 5.677,7.094 1.552,0.396 10 false Data set 4 was recorded when P0093 was stored

HINT:
·

The following can be deduced from the above freeze frame data:

-

The common rail fuel pressure dropped suddenly when the engine was being run at a moderate engine speed during engine warmup and DTC P0093 was stored at the point when data set 4 was recorded.

-

Injection Feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector assembly of cylinder 3 may be malfunctioning.


·

Actual cause: In this case, foreign matter in the fuel is stuck inside an injector assembly causing the injector assembly to malfunction temporarily.

In order to remove the foreign matter in the fuel (the main cause of the problem), the fuel filter case needs to be cleaned and the fuel filter needs to be replaced.



A206075E35
3.823,4.208 3.448,3.573 false 3.823,4.208 3.448,4.625 false 0.125,0.938 1.469,1.135 1.344,0.198 10 false Engine Speed (rpm) 0.125,2.458 1.24,2.667 1.115,0.208 10 false Fuel Press (kPa) 0.125,4.125 2.417,4.323 2.292,0.198 10 false Target Common Rail Pressure (kPa) 0.125,5.688 1.76,5.885 1.635,0.198 10 false Injection Volume (mm3/st) 1.344,2.229 1.469,2.396 0.125,0.167 10 false 0 1.115,1.792 1.469,1.958 0.354,0.167 10 false 1000 1.125,1.344 1.469,1.5 0.344,0.156 10 false 2000 1.323,3.792 1.427,3.979 0.104,0.188 10 false 0 1.031,3.365 1.438,3.521 0.406,0.156 10 false 32500 1.031,2.917 1.448,3.083 0.417,0.167 10 false 65000 1.323,5.375 1.427,5.563 0.104,0.188 10 false 0 1.031,4.938 1.438,5.094 0.406,0.156 10 false 35000 1.042,4.49 1.458,4.656 0.417,0.167 10 false 70000 1.344,6.948 1.448,7.135 0.104,0.188 10 false 0 1.063,6.51 1.427,6.667 0.365,0.156 10 false 60.00 1,6.063 1.448,6.229 0.448,0.167 10 false 120.00 0.104,0.073 4.313,0.25 4.208,0.177 10 false This is snapshot data which was taken when P0093 was stored (1): 3.396,3.938 3.542,4.125 0.146,0.188 10 false A 3.396,2.365 3.542,2.552 0.146,0.188 10 false A 3.396,7.083 3.542,7.271 0.146,0.188 10 false A 3.396,5.51 3.542,5.698 0.146,0.188 10 false A 3.865,4.146 4.063,4.344 0.198,0.198 10 false *1 0.104,0.417 6.427,0.604 6.323,0.188 10 false DTC P0093 was stored due to a decrease in fuel pressure when the accelerator pedal was depressed 2.583,7.083 2.771,7.271 0.188,0.188 10 false A'

HINT:

*1: Fuel press suddenly decreases for a moment, and then recovers. This can be seen clearly by comparing it to target common rail pressure.


A206076E29
4.583,4.198 4.094,3.24 false 1.333,2.219 1.438,2.406 0.104,0.188 10 false 0 1.021,1.771 1.427,1.927 0.406,0.156 10 false 50.00 0.969,1.323 1.438,1.49 0.469,0.167 10 false 100.00 1.063,3.823 1.427,4.01 0.365,0.188 10 false -10.0 1.323,3.375 1.438,3.531 0.115,0.156 10 false 0 1.125,2.927 1.427,3.094 0.302,0.167 10 false 10.0 0.229,0.833 1.51,1.031 1.281,0.198 10 false Accel Position (%) 0.229,2.552 2.458,2.698 2.229,0.146 10 false Injection Feedback Val #3 (mm3/st) 0.073,0.073 4.313,0.281 4.24,0.208 10 false This is snapshot data which was taken when P0093 was stored (2): 1.146,5.365 1.448,5.552 0.302,0.188 10 false OFF 1.188,5.021 1.438,5.177 0.25,0.156 10 false ON 0.208,4.26 0.51,4.406 0.302,0.146 10 false MIL 3.375,3.979 3.51,4.167 0.135,0.188 10 false A 3.385,2.365 3.521,2.552 0.135,0.188 10 false A 3.385,5.521 3.521,5.708 0.135,0.188 10 false A 4.542,4.208 4.76,4.365 0.219,0.156 10 false *2 0.073,0.417 6.417,0.604 6.344,0.188 10 false DTC P0093 was stored due to a decrease in fuel pressure when the accelerator pedal was depressed

HINT:

*2: Injection feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector assembly of cylinder 3 may be malfunctioning.


Reference Values for DTC P0093 Storage Point (Point A)
Data List Value Unit
Engine Speed 1478 rpm
Fuel Press 8900 kPa
Target Common Rail Pressure 65320 kPa
Injection Volume (Point A) 51.26*1 mm3/st
Injection Volume (Point A`) 9.76 mm3/st
Accel Position 63.67 %
Injection Feedback Val #1 -1.1 mm3/st
Injection Feedback Val #2 -2.5 mm3/st
Injection Feedback Val #3 5.0 mm3/st
Injection Feedback Val #4 -1.8 mm3/st
MIL ON -

PROCEDURE

1.CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS)
a.

Before starting the engine, visually check for fuel leaks from the fuel supply pump assembly, injector assembly, common rail assembly, and the fuel pipes in high-pressure areas.

OK:

No fuel leaks in high-pressure areas.




OK

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0093) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)

NG

REPAIR FUEL LEAK POINT

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0093) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.


d.

Read the DTCs and freeze frame data.

Result
Result Proceed to
P0093 and "P0190, P0192 and/or P0193" C
P0093 and "P0335 and/or P0339" B
Except above A



A

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

B

GO TO CRANKSHAFT POSITION SENSOR "A" CIRCUIT

C

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
a.

Check if the fuel level is low.

Result
Result Proceed to
The indicator (fuel warning light) is illuminated A
The indicator (fuel warning light) is not illuminated B



A

4.ADD FUEL

B

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)
4.ADD FUEL
a.

Add fuel.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.
A223284

Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:
·

Hand pump pumping speed: Max. 2 strokes/sec.

·

The hand pump must be pushed with a full stroke during pumping.

·

When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.

·

If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

·

If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter element sub-assembly, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

·

If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.




b.

Start the engine.

NOTICE:
·

If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.

·

Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

·

Use a fully-charged battery.



i.

When the engine can be started, proceed to the next step.


ii.

If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.



c.

Turn the ignition switch off.


d.

Connect the intelligent tester to the DLC3.


e.

Turn the ignition switch to ON and turn the intelligent tester on.



g.

Start the engine. (*A)


h.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak. (*B)


i.

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)


j.

Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)

A192848E03
0.177,1.313 1.583,1.583 1.406,0.271 10 false Active Test Operation 6.5,2.313 6.896,2.49 0.396,0.177 10 false Time 1.677,0.969 2.042,1.167 0.365,0.198 10 false ON 1.646,1.625 2.073,1.823 0.427,0.198 10 false OFF 2.563,1.927 3.375,2.094 0.813,0.167 10 false 10 seconds 3.188,0.656 4,0.823 0.813,0.167 10 false 10 seconds 2.635,0.24 3.229,0.417 0.594,0.177 10 false 1st time 3.896,0.24 4.5,0.427 0.604,0.188 10 false 2nd time 5.198,0.24 5.792,0.406 0.594,0.167 10 false 5th time 5.99,1.865 6.75,2.083 0.76,0.219 10 false 3 minutes


k.

Enter the following menus: Powertrain / Engine / DTC.


l.

Read Current DTCs.

i.

When no DTCs are output, the air bleeding is completed.


ii.

If any DTCs are output, proceed to the next step.



m.

Repeat steps (*A) to (*D).



o.

Start the engine and warm it up.


p.

Confirm that the shift lever is in neutral and securely apply the parking brake.


q.

Fully depress the accelerator pedal for 5 seconds, and then release it. (*E)


r.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)


s.

Repeat procedures (*E) and (*F) 5 times.

A220593E41
1.635,1.865 2.021,2.042 0.385,0.177 10 false 5000 1.469,0.594 1.969,0.771 0.5,0.177 10 false 160000 5.156,2.125 5.792,2.302 0.635,0.177 10 false 3000 rpm 1.865,2.563 1.99,2.74 0.125,0.177 10 false 0 1.854,1.24 1.979,1.417 0.125,0.177 10 false 0 0.073,0.781 1.031,0.948 0.958,0.167 10 false Fuel Pressure 0.083,2.125 1.042,2.292 0.958,0.167 10 false Engine Speed 0.083,3.417 1.25,3.583 1.167,0.167 10 false Accelerator Pedal 0.948,3.094 2.115,3.292 1.167,0.198 10 false Fully Depressed 1.021,3.729 2,3.927 0.979,0.198 10 false Fully Released 2.875,4.229 3.573,4.417 0.698,0.188 10 false 5 seconds 6.448,4.135 6.854,4.323 0.406,0.188 10 false Time 3.104,2.875 3.729,3.115 0.625,0.24 10 false Step (*E) 6.208,2.885 6.802,3.125 0.594,0.24 10 false Step (*E) 4.76,2.885 5.385,3.125 0.625,0.24 10 false Step (*F) 2.104,0.594 2.375,0.781 0.271,0.188 10 false kPa 2.104,1.844 2.417,2.01 0.313,0.167 10 false rpm


t.

Enter the following menus: Powertrain / Engine / DTC.


u.

Read Current DTCs.

Result
Result Proceed to
DTC output A
DTC not output B



A

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)

B

DTC CAUSED BY RUNNING OUT OF FUEL

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)
a.

Read the value of Injection Feedback Val #1 to #4 in the freeze frame data recorded in Procedure 2.

Result
Result Proceed to
Injection Feedback Val for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data B
Except above A

HINT:

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.




A

7.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

B

10.REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
7.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Start the engine.


f.

Read the value of Fuel Press while cranking and idling the engine.

Result
Result Proceed to
The engine cannot be started or the engine can be started but Fuel Press is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A



A

8.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)

B

15.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
8.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.


e.

Read the values.

Standard:
Tester Display Engine Condition* Normal Value
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Idling -3.0 mm3/st to 3.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 70°C (158°F) or higher and the engine should be idled for 1 minute or more.


Result
Result Proceed to
Injection Feedback Val for at least one cylinder is more than 3 mm3/st and engine vibration is abnormally large B
Except above A

HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.CHECK ENGINE SPEED

B

10.REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
9.CHECK ENGINE SPEED
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat procedure *1 5 times.

Result
Result Proceed to
No problems such as sluggishness or variations in the tachometer reading A
Except above B



A

11.BLEED AIR FROM FUEL SYSTEM

B

18.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
10.REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the fuel filter element sub-assembly.



NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.


d.
A176220E02
2.528,2.406 3.209,2.737 0.681,0.332 10 Snapshot Button 2.068,2.712 2.352,2.506 false 2.352,2.506 2.465,2.506 false

Take a snapshot with the intelligent tester during the Active Test.

HINT:

Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.



e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed (See Page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E60
3.406,2.427 3.521,2.094 3.521,2.094 3.594,2.094 false 4.406,2.594 5.01,2.417 5.01,2.417 5.073,2.417 false 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 false 3.708,3.292 3.938,4.208 3.938,4.208 4.073,4.208 false 0.083,1.427 1.448,1.583 1.365,0.156 10 false Active Test Operation 0.167,0.594 1.563,0.792 1.396,0.198 10 false Engine Speed (rpm) 0.542,3.271 1.448,3.51 0.906,0.24 10 false Fuel Pressure 3.646,2.01 5.042,2.219 1.396,0.208 10 false Target Fuel Pressure 6.469,4.146 6.865,4.323 0.396,0.177 10 false Time 2.125,2.427 2.865,2.792 0.74,0.365 10 false Less than 10000 kPa 2.99,4.271 3.677,4.438 0.688,0.167 10 false 2 seconds 5.135,2.333 6.052,2.708 0.917,0.375 10 false Abnormal Fuel Pressure 2.396,1.146 3.073,1.344 0.677,0.198 10 false Test Start 4.156,1.104 4.823,1.302 0.667,0.198 10 false Test Stop 5.542,1.104 6.219,1.302 0.677,0.198 10 false Test Start 2.208,1.823 3.031,2.198 0.823,0.375 10 false Normal Fuel Pressure 1.646,0.323 2.021,0.49 0.375,0.167 10 false 2000 1.885,0.865 2.052,1.031 0.167,0.167 10 false 0 1.75,1.344 2.073,1.51 0.323,0.167 10 false ON 1.698,1.594 2.021,1.76 0.323,0.167 10 false OFF 4.146,4.135 5.76,4.521 1.615,0.385 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure.



Result
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa A
Except above B



A

13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

B

15.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.





NEXT

14.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
14.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).



NEXT

16.BLEED AIR FROM FUEL SYSTEM
15.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).



NEXT

16.BLEED AIR FROM FUEL SYSTEM
16.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

17.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
17.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


b.

Perform the injector pilot quantity learning (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
18.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.


d.

Read the value while cranking and idling the engine.

Standard:
Tester Display Engine Condition Specified Condition
Engine Speed Cranking 50 to 400 rpm
Idling with warm engine 650 to 750 rpm


HINT:

The value should be the same as the actual engine speed and displayed with no interruption on the tester.




OK

19.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)

NG

22.REPLACE CRANKSHAFT POSITION SENSOR
19.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
U169104E02
1.521,0.875 1.76,1.656 true 1.417,0.313 1.719,0.49 0.302,0.177 10 false C90 0.073,0.063 0.292,0.25 0.219,0.188 10 false *a 1.458,1.688 2.302,1.938 0.844,0.25 10 false 16 (PCR1)

Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.

A192850E31
0.885,2.5 0.542,2.844 0.542,2.844 0.542,2.938 false 2.229,1.708 2.74,2.865 2.74,2.865 2.74,2.958 false 0.083,0.063 2.063,0.271 1.979,0.208 10 false Vibration Method (Reference) 0.24,2.958 1.125,3.198 0.885,0.24 10 false Engine Wire 2.104,2.99 3.615,3.406 1.51,0.417 10 false Common Rail Assembly (Fuel Pressure Sensor) 3.656,1.146 4.521,1.385 0.865,0.24 10 false Wire to Wire 1.469,0.479 2.031,0.708 0.563,0.229 10 false Engine 5.74,1.167 6.188,1.417 0.448,0.25 10 false ECM

A192849E35
2.115,1.865 3.073,0.677 3.073,0.677 3.167,0.677 false 3.104,1.865 3.74,1.5 3.74,1.5 3.823,1.5 false 3.865,1.427 5.906,1.865 2.042,0.438 10 false Sensor Output Signal with Noise (Problem with Wire Connection) 3.229,0.594 5.448,1.031 2.219,0.438 10 false Sensor Output Signal without Noise (Normal Wire Connection) 1.573,0.219 2.313,0.406 0.74,0.188 10 false Example: 4.385,2.49 6.656,2.688 2.271,0.198 10 false Tester Range (Reference): 4.385,2.844 6.813,3.042 2.427,0.198 10 false 200 mV/DIV., 500 μsec./DIV. or less

Standard Voltage:
Tester Connection Condition Specified Condition
C90-16 (PCR1) - Body ground Vibration is applied to the wire harness and connectors No noise in the waveform


Text in Illustration
*a Component with harness connected
(ECM)

Result
Result Proceed to
MIL comes on or noise present in the waveform B
Except above A



A

20.INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT)

B

23.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
20.INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Fuel Temperature.


d.

Read the value.

OK:

The value is almost the same as the actual fuel temperature.


HINT:
·

When the engine is stopped and left overnight, the fuel temperature becomes the same as the ambient temperature.

·

If there is a problem with the fuel temperature sensor, and a fuel temperature value lower than the actual fuel temperature is indicated, P0093 may be stored.





OK

21.CHECK FOR INTERMITTENT PROBLEMS

NG

27.REPLACE FUEL TEMPERATURE SENSOR
21.CHECK FOR INTERMITTENT PROBLEMS

NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
22.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL).

HINT:

Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.




NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
23.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
a.

Repair or replace the harness or connector.



NEXT

24.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
24.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
U169104E02
1.521,0.875 1.76,1.656 true 1.417,0.313 1.719,0.49 0.302,0.177 10 false C90 0.073,0.063 0.292,0.25 0.219,0.188 10 false *a 1.458,1.688 2.302,1.938 0.844,0.25 10 false 16 (PCR1)

Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.

Standard Voltage:
Tester Connection Condition Specified Condition
C90-16 (PCR1) - Body ground Vibration is applied to the wire harness and connectors No noise in the waveform


Text in Illustration
*a Component with harness connected
(ECM)

Result
Result Proceed to
MIL comes on or noise present in the waveform A
Except above B



A

25.REPLACE COMMON RAIL ASSEMBLY

B

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
25.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly (See page Engine / Hybrid System>1KD-FTV (FUEL)>COMMON RAIL>REMOVAL).

HINT:

Before replacing the common rail assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.




NEXT

26.BLEED AIR FROM FUEL SYSTEM
26.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
27.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor.

HINT:

Before replacing the fuel temperature sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.




NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.



e.

Start the engine.


f.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).


g.

Confirm that the shift lever is in neutral and securely apply the parking brake.


h.

Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)


i.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)


j.

Repeat procedures (*A) and (*B) 5 times.

A220593E43
1.635,1.865 2.021,2.042 0.385,0.177 10 false 5000 1.469,0.594 1.969,0.771 0.5,0.177 10 false 160000 5.156,2.125 5.792,2.302 0.635,0.177 10 false 3000 rpm 1.865,2.563 1.99,2.74 0.125,0.177 10 false 0 1.854,1.24 1.979,1.417 0.125,0.177 10 false 0 0.073,0.781 1.031,0.948 0.958,0.167 10 false Fuel Pressure 0.083,2.125 1.042,2.292 0.958,0.167 10 false Engine Speed 0.083,3.417 1.25,3.583 1.167,0.167 10 false Accelerator Pedal 0.948,3.094 2.115,3.292 1.167,0.198 10 false Fully Depressed 1.021,3.729 2,3.927 0.979,0.198 10 false Fully Released 2.875,4.229 3.573,4.417 0.698,0.188 10 false 5 seconds 6.448,4.135 6.854,4.323 0.406,0.188 10 false Time 3.104,2.875 3.729,3.115 0.625,0.24 10 false Step (*A) 6.208,2.885 6.802,3.125 0.594,0.24 10 false Step (*A) 4.76,2.885 5.385,3.125 0.625,0.24 10 false Step (*B) 2.104,0.594 2.375,0.781 0.271,0.188 10 false kPa 2.104,1.844 2.417,2.01 0.313,0.167 10 false rpm


k.

Enter the following menus: Powertrain / Engine / DTC.


l.

Read the DTCs.

OK:

No DTCs are output.




NEXT

END