Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0400  Exhaust Gas Recirculation Flow  


DESCRIPTION

The EGR system recirculates exhaust gases, and performs control so that the proper volume of exhaust gas is recirculated to suit all driving conditions. The recirculated gas mixes with the intake air, allowing the EGR system to slow down engine combustion and lower the combustion temperature. This helps reduce NOx emissions.

In order to increase circulation efficiency, the ECM adjusts the lift amount of the EGR valve and throttle valve.

P0400
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Decelerate from a speed of 50 km/h (80 mph) or more (release accelerator pedal for approximately 5 seconds) Mass air flow rate is not changed when the EGR valve is turned on (2 trip detection logic).
·

EGR valve stuck

·

EGR valve does not move smoothly

·

Electric vacuum regulating valve assembly

·

Vacuum switching valve (for EGR Cut)

·

Electric vacuum regulating valve assembly circuit

·

Vacuum switching valve (for EGR Cut) circuit

·

EGR blockage in line between exhaust manifold and intake manifold

·

Mass air flow meter

·

Intake system (leaks or blockages)

·

EGR cooler

·

Exhaust system (exhaust gas leaks)

·

ECM



Related Data List
DTC No. Data List
P0400
·

MAF

·

MAP

·

Actual EGR Valve Pos.

·

Target EGR Position

·

EGR Close Lrn. Val.

·

EGR Close Learn Val.

·

EGR Close Lrn. Status

·

EGR Lift Sensor Output



MONITOR DESCRIPTION

If the electric EGR control valve assembly is forcibly operated but the intake air amount does not vary, the ECM determines that the electric EGR control valve assembly is malfunctioning. The ECM then illuminates the MIL.


Flow malfunction

If the EGR valve is forcibly operated during deceleration but the intake air amount does not vary, the ECM determines that the EGR valve is malfunctioning. The ECM then illuminates the MIL (2 trip detection logic).


A194528E03
3.208,2.313 3.313,2.01 3.313,2.01 3.438,2.01 false 3.25,0.74 3.354,0.438 3.354,0.438 3.479,0.438 false 5.042,3.646 5.344,3.646 false 5.094,4.313 5.281,4.208 5.281,4.208 5.354,4.208 false 4.792,4.771 4.969,4.896 4.969,4.896 5.052,4.896 false 0.104,1.875 1.458,2.104 1.354,0.229 10 false Accelerator Opening 0.135,0.771 1.49,1 1.354,0.229 10 false Vehicle Speed 0.125,3.24 1.479,3.469 1.354,0.229 10 false EGR Valve Opening 0.115,4.365 1.948,4.615 1.833,0.25 10 false Mass Air Flow Meter Output 0.104,4.625 1.688,5.219 1.583,0.594 10 false (Changing Value of Intake Air Amount: gm/s) 1.51,2.25 2.083,2.5 0.573,0.25 10 false Closed 1.594,1.594 2.167,1.844 0.573,0.25 10 false Open 1.521,3.594 2.094,3.844 0.573,0.25 10 false Closed 1.615,2.885 2.188,3.135 0.573,0.25 10 false Open 3.5,1.958 5.01,2.208 1.51,0.25 10 false Fully Closed 3.563,0.365 5.365,0.74 1.802,0.375 10 false During Deceleration 5.438,3.542 6.365,3.875 0.927,0.333 10 false Fully Closed 5.427,4.135 6.083,4.375 0.656,0.24 10 false Normal 5.094,4.802 5.75,5.042 0.656,0.24 10 false Abnormal 6.448,5.146 6.865,5.438 0.417,0.292 10 false Time 0.177,0.052 1.5,0.302 1.323,0.25 10 false Flow Malfunction:

WIRING DIAGRAM

A221591E03
2.617,0.977 5.384,1.168 2.767,0.191 10 Electric Vacuum Regulating Valve Assembly 2.766,2.222 5.207,2.392 2.441,0.170 10 Vacuum Switching Valve (for EGR Cut) 2.617,0.773 2.933,0.962 0.316,0.189 10 C76 2.766,2.04 3.093,2.196 0.327,0.156 10 C77 1.358,0.639 2.125,0.809 0.767,0.170 10 EFI NO. 2 3.081,3.203 3.348,3.386 0.267,0.184 10 EFI 3.838,3.763 4.105,3.947 0.267,0.184 10 EFI 0.994,3.231 1.481,3.414 0.487,0.184 10 P/I-B 1.848,0.398 1.969,0.561 0.121,0.163 10 2 1.451,0.398 1.573,0.561 0.121,0.163 10 1 4.629,0.43 4.751,0.593 0.121,0.163 10 2 3.612,0.43 3.733,0.593 0.121,0.163 10 1 4.615,1.719 4.737,1.882 0.121,0.163 10 2 3.598,1.719 3.719,1.882 0.121,0.163 10 1 5.207,0.506 5.505,0.643 0.297,0.137 10 C93 5.214,1.813 5.512,1.950 0.297,0.137 10 C92 5.207,3.448 5.505,3.585 0.297,0.137 10 G58 5.551,3.357 5.963,3.503 0.413,0.146 10 MREL 5.551,1.802 5.991,1.948 0.441,0.146 10 EGRC 5.551,0.501 5.894,0.647 0.343,0.146 10 EGR 5.293,0.345 5.416,0.510 0.123,0.165 10 9 5.307,1.638 5.430,1.803 0.123,0.165 10 9 5.279,3.282 5.458,3.447 0.179,0.165 10 11 4.475,2.932 4.599,3.097 0.123,0.165 10 4 4.485,3.277 4.608,3.443 0.123,0.165 10 2 2.705,3.287 2.829,3.452 0.123,0.165 10 3 2.71,2.922 2.833,3.088 0.123,0.165 10 1 2.659,3.45 2.854,3.606 0.196,0.156 10 1B 4.438,3.455 4.668,3.611 0.230,0.156 10 1B 4.447,3.094 4.671,3.250 0.224,0.156 10 1B 2.654,3.084 2.861,3.239 0.207,0.156 10 1C 0.805,3.936 1.283,4.116 0.479,0.180 10 Battery 5.974,4.394 6.334,4.540 0.360,0.147 10 ECM 2.698,4.162 4.471,4.501 1.773,0.339 10 No. 1 Integration Relay (Engine Room Relay Block)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedures.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0400)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result
Display (DTC Output) Proceed to
P0400 A
P0400 and other DTCs B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EGR CUT)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EGR CUT)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.


f.

Read the MAF value displayed on the tester while the engine is idling.


g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cut or Activate the EGR valve Close.


h.

Read the mass air flow meter value when the VSV for EGR Cut or electric vacuum regulating valve assembly is turned from off to on using the Active Test function.

HINT:
·

If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.

·

When "Coolant Temp" is 75°C (167°F) or higher during idling, the exhaust gas flows through the EGR cooler. If MAF does not change when the EGR is cut even though the EGR valve is operating normally, the EGR cooler may be clogged.

·

When idling while warming up the engine, the actuator operates and the EGR cooler is bypassed. However, if the connector of the VSV for the EGR cooler is disconnected, the EGR cooler is not bypassed and it is possible to check how clogged the EGR cooler is.



Result
Active Test Result Proceed to
Activate the VSV for EGR Cut:
Off (Open) to on (Close)
MAF value does not change A
MAF value changes B

NOTICE:

As the values shown below may differ due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric vacuum regulating valve assembly or mass air flow meter.


Reference:
EGR Valve Condition (Opening) Measuring Condition MAF (Reference)
Open (55%)
·

Atmosphere pressure: 101 kPa

·

Intake air temperature: 30°C (86°F)

·

Engine coolant temperature: 88°C (190°F)


4.5 to 10.5 g/sec
Close (0%) 13 to 20 g/sec




A

3.CHECK VACUUM HOSES

B

6.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE OPERATION)
3.CHECK VACUUM HOSES
a.

Check the vacuum hoses.


OK:

The hoses are not damaged and are securely connected



OK

4.INSPECT ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

NG

8.REPAIR OR REPLACE VACUUM HOSE
4.INSPECT ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
a.

Inspect the electric vacuum regulating valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>VACUUM REGULATING VALVE>INSPECTION).


HINT:

Before replacing the electric vacuum regulating valve assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



OK

5.INSPECT VACUUM SWITCHING VALVE (FOR EGR CUT)

NG

9.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
5.INSPECT VACUUM SWITCHING VALVE (FOR EGR CUT)
a.

Inspect the vacuum switching valve (for EGR cut) (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>VACUUM SWITCHING VALVE>ON-VEHICLE INSPECTION).

HINT:

Before replacing the vacuum switching valve (for EGR cut), perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.




OK

6.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE OPERATION)

NG

10.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR CUT)
6.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE OPERATION)
a.

Inspect the electric EGR control valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>INSPECTION).


OK:

The valve is not stuck and does not have heavy carbon deposits



OK

7.CHECK FOR DEPOSIT (EGR PASSAGE)

NG

9.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
7.CHECK FOR DEPOSIT (EGR PASSAGE)
a.

Check the deposit conditions in the EGR cooler and the EGR passage.


OK:

The EGR passage is not clogged and does not have heavy carbon deposits


HINT:

When performing the check for deposits, check the interior of the EGR valve, EGR pipe, EGR cooler, EGR cooler bypass valve and the entire EGR passage.



OK

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)

NG

11.REPAIR OR REPLACE MALFUNCTIONING PARTS
8.REPAIR OR REPLACE VACUUM HOSE
a.

Repair or replace the vacuum hose.



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
9.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
10.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR CUT)
a.

Replace the vacuum switching valve (for EGR cut).



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
11.REPAIR OR REPLACE MALFUNCTIONING PARTS

NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up.


f.

Move the shift lever to 2nd gear and decelerate from a speed of 50 km/h (31 mph) or more (fully release the accelerator for approximately 5 seconds or more).


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read DTCs.


HINT:

When a DTC is output, the mass air flow meter may be malfunctioning.



NEXT

END