Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2018.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  P244A  Diesel Particulate Filter Differential Pressure Too Low  P2458  Diesel Particulate Filter Regeneration Duration  P2463  Diesel Particulate Filter Restriction - Soot Accumulation  


DESCRIPTION

DPF (Diesel Particulate Filter) is an emission control system which processes the particulate matter (PM) that is emitted from a diesel engine. The DPF catalyst has a porous ceramic structure which has a PM collecting function. The PM that is collected is continuously treated by oxidation due to catalytic action at high temperatures, however PM accumulation increases at low catalyst temperatures because the oxidation process slows down. The ECM performs PM forced regeneration so that the amount of accumulated PM does not exceed the threshold.

A357988E01
1.063,0.75 0.865,0.146 0.865,0.146 1,0.146 true 2.833,1.75 3.031,1.333 3.031,1.333 3.167,1.333 true 2.979,2.354 3.177,1.938 3.177,1.938 3.313,1.938 true 3.479,2.698 3.688,2.552 3.688,2.552 3.823,2.552 true 2.854,3.406 3.677,2.948 true 2.844,3.719 3.406,4.063 3.406,4.063 3.542,4.063 true 1.802,2.354 2.406,2.208 true 1.823,2.708 2.417,2.479 true 1.76,3.365 2.406,2.833 true 3.396,6.323 3.583,6.052 true 1.344,6.583 1.615,7.188 true 3.406,6.323 4.688,6.219 true 6.021,6.771 5.698,6.563 true 6.365,6.313 6.406,6.031 true 1.083,0.083 3.042,0.292 1.958,0.208 10 false Exhaust Fuel Addition Injector 0.052,0.75 0.625,1.135 0.573,0.385 10 false Exhaust Gas 3.24,1.26 5.875,1.49 2.635,0.229 10 false Exhaust Gas Temperature Sensor 3.375,1.865 5.865,2.25 2.49,0.385 10 false No. 2 Exhaust Gas Temperature Sensor 3.865,2.469 5.646,2.677 1.781,0.208 10 false Differential Pressure Sensor 3.76,2.823 5.76,3.219 2,0.396 10 false No. 3 Exhaust Gas Temperature Sensor 3.625,3.969 5.406,4.177 1.781,0.208 10 false Air Fuel Ratio Sensor 0.885,2.281 1.802,2.49 0.917,0.208 10 false DOC Catalyst 0.135,2.625 1.823,3.031 1.688,0.406 10 false Exhaust Manifold Converter Sub-assembly 0.917,3.271 1.833,3.479 0.917,0.208 10 false DPF Catalyst 0.406,4.677 2.292,4.906 1.885,0.229 10 false DPF (Diesel Particulate Filter): 3.417,4.677 4.99,4.906 1.573,0.229 10 false Monolithic Construction: 5.563,4.677 7.135,4.906 1.573,0.229 10 false Wall-Flow Type: 2.427,5.26 3.385,5.5 0.958,0.24 10 false PM, HC, CO 2.167,6.24 3.427,6.635 1.26,0.396 10 false Alternating Blocked Passages 1.698,7.104 4.135,7.344 2.438,0.24 10 false DPF (Diesel Particulate Filter) Catalyst 6.073,6.708 6.448,6.885 0.375,0.177 10 false PM 5.417,7.073 6.49,7.292 1.073,0.219 10 false Magnified View 6.115,6.292 6.792,6.5 0.677,0.208 10 false Gas Flow 4.771,5.281 5.469,5.51 0.698,0.229 10 false CO2, H2O 3.698,6.375 4.625,6.625 0.927,0.25 10 false Cross Section

P0420
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration During PM forced regeneration, DOC catalyst temperature does not increase sufficiently for 3 minutes.
(2 trip detection logic)
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



P244A
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration When driving, the catalyst differential pressure is continuously below the threshold for 7 seconds or more.
(2 trip detection logic)
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



P2458
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration When PM forced regeneration is manually performed, PM forced regeneration does not finish even after 60 minutes or more elapse.
(1 trip detection logic)
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



P2463
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration While driving, PM accumulation amount exceeds the limit.
(1 trip detection logic)
·

Exhaust Manifold Converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



HINT:

PM forced regeneration may be prohibited due to a fail-safe operation that is performed when another DTC is stored (including engine output limitation).


Related Data List
DTC No. Data List
P0420
P244A
P2458
P2463
·

Exhaust Fuel Addition FB

·

Catalyst Differential Press



MONITOR DESCRIPTION

The ECM monitors the differential pressure between the upstream and downstream of the DPF catalyst and also monitors exhaust gas temperature to detect a malfunction in the exhaust manifold converter sub-assembly .

Abnormal DOC catalyst temperature increase:

The ECM monitors exhaust gas temperature increase while the exhaust fuel addition injector assembly adds fuel during PM forced regeneration. Exhaust gas temperature increases up to approximately 300 to 500°C (572 to 932°F) during PM forced regeneration. If the temperature does not increase even after a certain amount of time has elapsed, the ECM determines that the DOC catalyst is abnormal and illuminates the MIL.


A208470E08
3.229,1.875 3.323,2.031 3.323,2.031 3.49,2.031 false 5.229,1.875 5.302,1.625 5.302,1.625 5.417,1.625 false 5.135,1.458 5.083,1.281 5.083,1.281 4.958,1.281 false 5.313,1.427 5.396,0.875 5.396,0.875 5.531,0.875 false 0.083,0.083 2.01,0.5 1.927,0.417 10 false Catalyst Activation Malfunction: (DPF No Activate) 0.896,0.938 2.583,1.417 1.688,0.479 10 false PM Forced Regeneration (Activation of Fuel Addition) 1.115,1.781 2.75,2.073 1.635,0.292 10 false Exhaust Gas Temperature 3.51,1.958 5.677,2.229 2.167,0.271 10 false About 150 to 300°C (302 to 572°F) 5.458,1.563 6.115,1.781 0.656,0.219 10 false Abnormal 4.49,1.208 5,1.49 0.51,0.281 10 false Normal 3.323,0.813 3.635,1 0.313,0.188 10 false Off 5.135,0.385 5.375,0.542 0.24,0.156 10 false On 5.563,0.802 7.01,1.25 1.448,0.448 10 false More than About 500°C (932°F) 4.24,2.438 4.594,2.594 0.354,0.156 10 false Time

Catalytic converter differential pressure too low:

The ECM monitors the DPF catalyst differential pressure when driving and illuminates the MIL when the difference in pressure before and after the catalyst is below the threshold


Catalytic converter Regeneration Duration:

When PM forced regeneration is manually performed, PM forced generation does not finish even after 60 minutes or more elapse, the ECM determines that there is problem with the DPF catalyst and illuminates the MIL.


Excessive PM accumulation:

The ECM monitors the PM Accumulation Ratio and when the accumulated PM volume in the DPF catalyst exceeds the limit, the ECM illuminates the MIL.


CAUTION / NOTICE / HINT

NOTICE:


HINT:
·

If DTC P2458 or P2463 is stored, fail-safe controls engine power output and PM forced regeneration is prohibited. In this case, PM forced regeneration can be performed after disconnecting the EFI-MAIN NO. 1 fuse or battery terminal and waiting for 60 seconds or more before connecting it again.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Record the stored DTC and freeze frame data.


e.

Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition FB value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM regeneration control.

·

When the Catalyst Differential Press value is 0.27 or more, it indicates a high possibility that DPF catalyst is clogged.





NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420, P244A, P2458 AND P2463)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420, P244A, P2458 AND P2463)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P244A is output A
DTC P244B is output at the same time as P2463* B
DTC P0420, P2458 or P2463 is output C
Other relevant DTCs are output D

HINT:
·

*: When DTC P244B is output at the same time as P2463, perform troubleshooting for P244B.

·

When DTC P1603, P1604 or P1608 is output in addition to P0420, perform troubleshooting for P1603, P1604 or P1608 first.





A

3.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE

B

C

11.CHECK FOR BLACK SMOKE

D

10.GO TO DTC CHART
3.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


HINT:

Before checking the differential pressure sensor, perform a visual inspection of the differential pressure pipes and check that they are properly connected and no air is leaking from the pipes or hoses. If a malfunction is found, repair it before checking the sensor.

A360341E04
3.667,0.844 4.688,0.656 true 2.917,0.552 3.458,0.75 true 4.208,1.927 4.677,1.667 true 2.281,1.729 2.698,2.052 true 1.896,0.469 2.844,0.833 0.948,0.365 10 false Vacuum hoses (Downstream) 4.792,0.583 5.74,0.948 0.948,0.365 10 false Vacuum hoses (Upstream) 4.74,1.583 6.052,1.781 1.313,0.198 10 false No. 1 Vacuum Pipe 1.042,1.646 2.323,1.865 1.281,0.219 10 false No. 2 Vacuum Pipe


a.
A362182E02
0.969,1.021 1.479,1.25 true 0.979,1.021 1.75,1.198 true 0.063,0.917 1.042,1.125 0.979,0.208 10 false Vacuum Hose

Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both air hoses during idling.

OK:

Exhaust gas pulsation exists.




NG

4.REPAIR OR REPLACE NO. 1 VACUUM PIPE OR NO. 2 VACUUM PIPE

OK

5.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
4.REPAIR OR REPLACE NO. 1 VACUUM PIPE OR NO. 2 VACUUM PIPE
a.

Repair or replace No. 1 vacuum pipe or No. 2 vacuum pipe.



NEXT

5.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
5.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


d.

Check that the differential pressure is as specified below.

Result
Data List Condition Differential Pressure Output
DPF Differential Pressure Engine switch on (IG) Approximately 0 kPa



OK

6.CONNECT UPSTREAM AIR HOSE

NG

7.REPLACE DIFFERENTIAL PRESSURE SENSOR
6.CONNECT UPSTREAM AIR HOSE
a.
A362181E01
1.792,1.167 2.479,0.948 true 2.531,0.854 3.427,1.208 0.896,0.354 10 false Vacuum Hose (Upstream)

Connect the upstream air hose to the differential pressure sensor.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


e.

Start the engine.


f.

Engine is running at 4000 rpm with no load for 10 seconds or more.


g.

Check that the differential pressure is as specified below.

Result
DPF Differential Pressure Proceed to
1.5 kPa or higher A
below 1.5 kPa B

HINT:

If the downstream differential pressure hose is disconnected, only the pressure of the upstream part of the differential pressure sensor changes. Therefore, the DPF differential pressure indicates the absolute value of the pressure before the DPF. If this occurs, as long as the characteristic of the differential pressure sensor is normal, the DPF differential pressure is equivalent to the back pressure (1.5 kPa or more).




B

7.REPLACE DIFFERENTIAL PRESSURE SENSOR

A

8.CONNECT DOWNSTREAM AIR HOSE (DOWNSTREAM)
7.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.


NEXT

8.CONNECT DOWNSTREAM AIR HOSE (DOWNSTREAM)
8.CONNECT DOWNSTREAM AIR HOSE (DOWNSTREAM)
a.

Connect the downstream air hose to the differential pressure sensor.

A360341E05
2.875,0.5 3.438,0.906 true 1.885,0.406 2.854,0.813 0.969,0.406 10 false Vacuum hoses (Downstream)


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


e.

Start the engine.


f.

Engine is running at 4000 rpm with no load for 10 seconds or more.


g.

Check that the differential pressure is as specified below.

Result
DPF Differential Pressure Proceed to
-1.5 to 1.5 kPa A
Higher than 1.5 kPa B



A

9.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

B

11.CHECK FOR BLACK SMOKE
9.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

If the differential pressure before and after the DPF is low, it is very likely that there is no DPF or the material inside the DPF is missing due to erosion, etc. If the DPF catalyst is eroded, do not replace the DPF at this time, as troubleshooting the cause and other repairs are necessary.




NEXT

13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
10.GO TO DTC CHART

NEXT

11.CHECK FOR BLACK SMOKE
11.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the above procedure [A] 10 times [B].


e.

Check for black smoke emission during procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.




NG

12.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

OK

13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
12.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.




NEXT

13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
a.

Remove the EFI-MAIN NO.1 fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI-MAIN NO.1 fuse or reconnect the cable to the battery terminal.

HINT:
·

The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.

·

If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.




b.

Turn the engine switch on (IG).


c.

Turn the engine switch off and wait for 30 seconds or more.


d.

Turn the engine switch on (IG) and wait for 10 seconds or more


e.

Connect the GTS to the DLC3.


f.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


g.

Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.

HINT:
·

If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.

·

When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.




h.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the DPF Rejuvenate (PM) /Data List / Diesel Exhaust / Exhaust Temperature Sensor B1S2.


i.

Perform the Active Test.

CAUTION:

Be careful of the exhaust pipes and surrounding areas, as they become extremely hot when performing PM forced regeneration.


HINT:

When PM Accumulation Ratio is too low, Activate the DPF Rejuvenate (PM) cannot be performed. Therefore, rev the engine with no load at 3400 rpm for 5 to 10 minutes to increase PM Accumulation Ratio to 12% or more.



j.

Check for temperature increases and abnormal white smoke during PM forced regeneration.

HINT:
·

PM forced regeneration takes 15 to 40 minutes to finish.

·

The time it takes to complete PM forced regeneration changes depending on "PM Accumulation Ratio" and the vehicle operating conditions.

·

If the value of "Catalyst Differential Press" increases too much during the PM forced regeneration, the fail-safe function activates and PM forced regeneration is stopped.

·

Perform PM forced regeneration control until the display on the multi-information display turns off.

·

If actions such as depressing the accelerator pedal or clutch pedal, etc. are performed during PM forced regeneration, PM forced regeneration stops. If PM forced regeneration stops, it is necessary to perform it again.

·

PM forced regeneration control is not complete until the display on the multi-information display turns off.



Result
Result Proceed to
During PM forced regeneration, temperature of Exhaust Temperature Sensor B1S2 is 300 to 500°C and no white smoke is generated A
During PM forced regeneration, temperature of Exhaust Temperature Sensor B1S2 is 300 to 500°C and abnormal white smoke is generated*1 B
Other than above*2 C

HINT:
·

*1: If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst.

·

*1: When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.

·

*2: An excess of accumulated PM is the result of a malfunction in the control system causing poor combustion and an increase in black smoke.





A

14.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

15.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

16.CHECK FUEL INJECTION SYSTEM
14.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

It has been determined that the exhaust fuel addition injector assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust fuel addition injector assembly.



NEXT

16.CHECK FUEL INJECTION SYSTEM
15.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst. When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.




NEXT

16.CHECK FUEL INJECTION SYSTEM
16.CHECK FUEL INJECTION SYSTEM

NEXT

17.CHECK INTAKE / EXHAUST SYSTEM
17.CHECK INTAKE / EXHAUST SYSTEM

NEXT

18.CHECK AFTER TREATMENT CONTROL SYSTEM
18.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

19.REPAIR OR REPLACE MALFUNCTIONING PARTS
19.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P0420, P244A, P2458 and P2463.


a.

Replace the exhaust fuel addition injector assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL).


b.

Replace the exhaust manifold converter sub-assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL).

NOTICE:

Perform Initialization procedure for "DPF catalyst record clear" and "DPF Deterioration Record Clear" (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).



c.

Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system, intake/exhaust system and after treatment control system.


d.

Check for DTCs output in step 1.

Result:
Result Proceed to
DTC P244A is output A
DTC other than P244A output B




A

20.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

B

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


d.

Start the engine.


e.

Engine is running at 4000 rpm with no load for 10 seconds or more.


f.

Confirmation that the differential pressure is higher than 1.5 kPa.



NEXT

END

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.




NEXT

END