Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P244B  Diesel Particulate Filter Differential Pressure Too High  


DESCRIPTION

Refer to DTC P0420 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P0420).

P244B
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine is running at 4000 rpm with no load for 10 seconds or more. While driving, Catalyst Differential Pressure becomes more than 0.27 for 3 seconds.
(1 trip detection logic)
·

Exhaust manifold converter sub-assembly (DPF catalyst)

·

Differential pressure sensor


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



Related Data List
DTC No. Data List
P244B
·

DPF Differential Pressure

·

Catalyst Differential Press

·

Exhaust Fuel Addition FB



MONITOR DESCRIPTION

The ECM compares pressure upstream and downstream of the DPF catalyst to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst is contaminated or has deteriorated and illuminates the MIL.

A244057E12
2.125,3.344 2.344,3.344 false 2.344,3.344 2.729,1.885 false 4,1.177 4.521,0.448 false 4.521,0.448 4.698,0.448 false 5.844,2.5 5.302,2.135 false 5.844,2.5 5.979,2.5 false 1.229,3.271 2.125,3.625 0.896,0.354 10 false Stores P244B 3.531,2.938 3.99,3.167 0.458,0.229 10 false MAF 0.167,0.177 2.323,0.406 2.156,0.229 10 false Differential Pressure Malfunction: 0.25,1.604 1.333,2.021 1.083,0.417 10 false DPF Differential Pressure 4.771,0.375 5.969,0.604 1.198,0.229 10 false Clogged with PM 5.76,1.406 7.146,1.833 1.385,0.427 10 false Increases PM amount of DPF catalyst 6.052,2.396 6.99,2.781 0.938,0.385 10 false No PM in DPF catalyst 1.125,0.938 1.51,1.167 0.385,0.229 10 false High 5.604,2.938 5.99,3.167 0.385,0.229 10 false High 1.125,2.656 1.51,2.885 0.385,0.229 10 false Low 1.573,2.969 1.958,3.198 0.385,0.229 10 false Low

CAUTION / NOTICE / HINT

NOTICE:


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Record the stored DTC and freeze frame data.


e.

Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition FB value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM forced regeneration.

·

When the Catalyst Differential Press value is 0.27 or more, it indicates a high possibility that DPF catalyst is clogged.





NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P244B is output A
DTC P244B is output at the same time as P2463*
Other relevant DTCs are output B

HINT:

*: When P244B is output at the same time as P2463, perform this diagnostic procedure. When DTC P244B is not output at the same time as P2463 is output, perform the diagnostic procedure for P0420 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P0420).




A

3.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

B

9.GO TO DTC CHART
3.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


d.

Check the DPF Differential Pressure values from idle speed to unloaded maximum engine speed.

Result
Result Proceed to
DPF Differential Pressure increases as engine speed increases from idle speed A
Except above B

A241154E05
3.323,3.479 3.479,3.479 3.479,3.479 3.708,3.885 false 4.219,4.365 4.063,4.365 4.063,4.365 3.854,4.021 false 4.135,5.021 4.01,5.021 4.01,5.021 3.823,4.792 false 0.479,1.635 1.75,2.021 1.271,0.385 10 false Engine Speed (rpm) 0.854,2.906 1.76,3.292 0.906,0.385 10 false MAF (gm/s) 0.688,4.115 1.667,4.531 0.979,0.417 10 false DPF Differential Pressure (kPa) 4.188,4.938 4.417,5.177 0.229,0.24 10 false A 1.792,1.75 1.896,2.031 0.104,0.281 10 false 0 1.792,3.125 1.896,3.406 0.104,0.281 10 false 0 1.792,4.51 1.896,4.792 0.104,0.281 10 false 0 0.708,0.958 1.927,1.344 1.219,0.385 10 false Unloaded Maximum Engine Speed 2.438,3.385 3.385,3.667 0.948,0.281 10 false Normal Piping 4.271,4.292 5.333,4.594 1.063,0.302 10 false Clogged Piping 2.344,5.375 5.365,5.656 3.021,0.281 10 false Negative pressure occurs for approx. 1 second.

HINT:

If DPF Differential Pressure indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.




B

4.CLEAN OR REPLACE AIR HOSE

A

5.CHECK FOR BLACK SMOKE
4.CLEAN OR REPLACE AIR HOSE
a.

Even though it has been determined that the air hose needs to be repaired or cleaned, make sure to perform all diagnostic procedures for DTC P244B before repairing or cleaning it.



NEXT

5.CHECK FOR BLACK SMOKE
5.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the above procedure [A] 10 times [B].


e.

Check for black smoke emission during procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.




OK

6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)

NG

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst Differential Press.


d.

Check the value of Catalyst Differential Press at 4000 rpm without load.

Result
Result Proceed to
Catalyst Differential Press is more than 0.27 A
Except above B



B

7.PERFORM PM FORCED REGENERATION

A

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
7.PERFORM PM FORCED REGENERATION
a.

Remove the EFI-MAIN NO.1 fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI-MAIN NO.1 fuse or reconnect the cable to the battery terminal.

HINT:
·

The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.

·

If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.




b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.



e.

Perform PM forced regeneration (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

Result:

PM forced regeneration completes normally.




OK

END

NG

10.CHECK FUEL INJECTION SYSTEM
8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Even though it has been determined that the exhaust manifold converter sub-assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B before replacing it.


NEXT

10.CHECK FUEL INJECTION SYSTEM
9.GO TO DTC CHART

NEXT

10.CHECK FUEL INJECTION SYSTEM
10.CHECK FUEL INJECTION SYSTEM

NEXT

11.CHECK INTAKE / EXHAUST SYSTEM
11.CHECK INTAKE / EXHAUST SYSTEM

NEXT

12.CHECK AFTER TREATMENT CONTROL SYSTEM
12.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

13.REPAIR OR REPLACE MALFUNCTIONING PARTS
13.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Repair, replace or clean the following items only when it has been determined necessary based on diagnosis for DTC P244B and P2463.


a.

Clean and/or repair the hoses of the differential pressure sensor.


b.

Replace the exhaust manifold converter sub-assembly (DPF catalyst) (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL).

NOTICE:

Perform Initialization procedure for "DPF catalyst record clear" and "DPF Deterioration Record Clear" (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).




NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.





NEXT

END