Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM J

1GD-FTV ENGINE CONTROL  ECD SYSTEM  Active Control Engine Mount System  


DESCRIPTION

The active control engine mount system decreases engine vibration at low engine speed using the vacuum switching valve sub-assembly (for engine mounting). The vacuum switching valve sub-assembly (for engine mounting) is controlled by a pulse signal transmitted to the vacuum switching valve sub-assembly (for engine mounting) from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.

WIRING DIAGRAM

A356524E07
3.052,1.219 3.25,1.406 0.198,0.188 10 false 1 4.448,1.229 4.646,1.417 0.198,0.188 10 false 2 5.813,1.094 6.26,1.281 0.448,0.188 10 false C150 5.896,0.896 6.094,1.083 0.198,0.188 10 false 12 6.24,1.104 6.688,1.292 0.448,0.188 10 false ACM 6.25,5.208 6.781,5.396 0.531,0.188 10 false MREL 5.802,5.365 6.25,5.552 0.448,0.188 10 false G184 4.979,5.354 5.25,5.542 0.271,0.188 10 false 1K 5.031,5.167 5.229,5.354 0.198,0.188 10 false 7 4.979,3.875 5.25,4.063 0.271,0.188 10 false 1K 4.979,3.667 5.177,3.854 0.198,0.188 10 false 22 3.438,4.542 4.26,4.729 0.823,0.188 10 false EFI MAIN 2 3.438,5.688 4.26,5.875 0.823,0.188 10 false EFI MAIN 1 4.219,4.01 5.042,4.198 0.823,0.188 10 false EFI NO. 2 2.448,4.031 3.615,4.219 1.167,0.188 10 false EFI-MAIN NO. 2 2.448,5.146 3.615,5.333 1.167,0.188 10 false EFI-MAIN NO. 1 1.719,3.875 1.99,4.063 0.271,0.188 10 false 1C 1.729,5.365 2,5.552 0.271,0.188 10 false 1J 1.771,5.188 1.969,5.375 0.198,0.188 10 false 3 1.76,3.677 1.958,3.865 0.198,0.188 10 false 1 0.396,4.677 1.219,4.865 0.823,0.188 10 false P/I-B 2.615,1.615 5.063,2.323 2.448,0.708 10 false Vacuum Switching Valve Sub-assembly (for Engine Mounting) 2.604,1.438 3.427,1.625 0.823,0.188 10 false C80 5.906,5.146 6.104,5.333 0.198,0.188 10 false 14 6.427,6.052 6.854,6.24 0.427,0.188 10 false ECM 2.76,6.083 4.396,6.271 1.635,0.188 10 false No. 1 Integration Relay 0.552,6.01 2.188,6.198 1.635,0.188 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.INSPECT INTAKE SYSTEM
a.

Inspect intake system (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

Result:

Repair any trouble areas.




OK

2.INSPECT VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING) (RESISTANCE)

NG

REPAIR INTAKE SYSTEM

2.INSPECT VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING) (RESISTANCE)
a.

Inspect the vacuum switching valve sub-assembly (for engine mounting) (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>VACUUM SWITCHING VALVE (for Engine Mounting)>INSPECTION).



OK

3.INSPECT FRONT ENGINE MOUNTING INSULATOR

NG

REPLACE VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING)

3.INSPECT FRONT ENGINE MOUNTING INSULATOR
a.

Disconnect the vacuum hose from the front engine mount insulator assembly.


b.

Using a vacuum pump, apply vacuum of 80 kPa (600 mmHg, 23.622 in.Hg) and wait for 1 minute.


c.

Check that there is no change in the needle movement of the vacuum pump gauge.


d.

Check that there is no fluid leakage caused by a break in the diaphragm.

OK:

Vacuum does not leak.



e.

Reconnect the vacuum hose.



OK

4.INSPECT VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING) (POWER SOURCE VOLTAGE)

NG

REPLACE FRONT ENGINE MOUNTING INSULATOR

4.INSPECT VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING) (POWER SOURCE VOLTAGE)
a.
U169380E01
0.177,0.021 0.344,0.188 0.167,0.167 10 false *a 0.469,0.771 0.844,0.927 0.375,0.156 10 false C80

Disconnect the vacuum switching valve sub-assembly (for engine mounting) connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C80-1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to Vacuum Switching Valve Sub-assembly (for Engine Mounting))


d.

Reconnect the vacuum switching valve sub-assembly (for engine mounting) connector.



OK

5.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING) - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY SUB-ASSEMBLY (FOR ENGINE MOUNTING) - NO. 1 INTEGRATION RELAY)
5.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING) - ECM)
a.

Disconnect the vacuum switching valve sub-assembly (for engine mounting) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C80-2 - C150-12 (ACM) Always Below 1 Ω
C80-2 or C150-12 (ACM) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the vacuum switching valve sub-assembly (for engine mounting) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VACUUM SWITCHING VALVE SUB-ASSEMBLY(FOR ENGINE MOUNTING) - ECM)

6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY SUB-ASSEMBLY (FOR ENGINE MOUNTING) - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the vacuum switching valve sub-assembly (for engine mounting) connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
1K-22 - C80-1 Always Below 1 Ω
K-22 or C80-1 - Body ground and other terminals Always 10 kΩ or higher




OK

7.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN2)
a.


OK

NG

REPLACE NO. 1 INTEGRATION RELAY