1.REMOVE ENGINE ASSEMBLY
19500
2.REMOVE IGNITION COIL ASSEMBLY
27020
3.REMOVE GENERATOR ASSEMBLY
16620D
4.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 2 bolts and V-ribbed belt tensioner assembly.
88431
5.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
16321
6.REMOVE WATER INLET
16331A
7.REMOVE THERMOSTAT
17111
8.REMOVE INTAKE MANIFOLD
16603
9.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt, No. 1 idler pulley sub-assembly and spacer.
11301M
10.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)
11301M
11.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)
11101J
12.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)
11301K
13.REMOVE CRANKSHAFT POSITION SENSOR
16268
14.REMOVE NO. 1 WATER BY-PASS PIPE
w/ Engine Oil Cooler:
Slide the clip and disconnect the No. 6 water by-pass hose from the No. 1 water by-pass pipe.
| *A | w/o Engine Oil Cooler |
| *B | w/ Engine Oil Cooler |
Remove the 2 nuts, bolt, No. 1 water by-pass pipe and gasket.
11201
15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Slide the clip and disconnect the PCV hose from the PCV valve sub-assembly.
Remove the 21 bolts, 2 nuts, 2 plate washers, 2 seal washers and cylinder head cover sub-assembly.
Remove the gasket from the cylinder head cover sub-assembly.
Remove the No. 1 camshaft bearing cap oil hole gasket from the cylinder head cover spacer.
13471
16.REMOVE CRANKSHAFT PULLEY
12144
17.REMOVE OIL PAN COVER SILENCER
Remove the 2 No. 1 oil pan plugs and oil pan cover silencer.
12102A
18.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the oil pan drain plug and gasket.
Remove the 16 bolts, 2 adjusting screws, and 2 nuts.
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
Be careful not to damage the contact surfaces of the oil pans.
12101
19.REMOVE OIL PAN SUB-ASSEMBLY
Remove the 16 bolts and 2 nuts.
Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block with a screwdriver.
| *a | Protective Tape |
Be careful not to damage the contact surfaces of the cylinder block and oil pan sub-assembly.
Tape the screwdriver tip before use.
Remove the gasket from the oil strainer sub-assembly.
11302
20.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 16 bolts and nut shown in the illustration.
Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.
| *a | Protective Tape |
Do not damage the surrounding parts.
Tape the screwdriver tip before use.
Remove the 3 O-rings from the timing chain cover sub-assembly.
16100
21.REMOVE ENGINE WATER PUMP ASSEMBLY
Remove the 8 bolts, engine water pump assembly and gasket.
11301C
22.REMOVE TIMING CHAIN COVER OIL SEAL
Using a screwdriver wrapped in protective tape, pry out the timing chain cover oil seal from the timing chain cover sub-assembly.
| *a | Protective Tape |
Be careful not to damage the timing chain cover sub-assembly.
Tape the screwdriver tip before use.